GOLDEN LIGHTING 3690-A1W NB-IL Kennedy Natural Black Hardwired/Plug-In Swing Arm Wall Lamp Instruction Manual

GOLDEN LIGHTING 3690-A1W NB-IL Kennedy Natural Black Hardwired/Plug-In

Swing Arm Wall Lamp Instruction Manual

Thank You for Choosing Golden Lighting for Your Lighting Needs!

Pendants types

1. Pendants & Linear Pendants Above a Kitchen Island
   Center a linear pendant over the island. If hanging pendants, use one pendant for every 24″ of island. Fixtures should hang at least 30″ above the countertop.

2. Pendants & Chandeliers Above a Dining Room Table
   Fixtures should stay at least 30″ above the table. Use a fixture that is 12″ narrower than the width of the table.

4. Pendants and Chandeliers in Open Areas
   The bottom should hang at least 7.5 feet from the floor. Allow clearance for any opening doors.

We appreciate your business and hope you love your new light!

Great lighting can add value and enhance the look of your home. To ensure the best lighting in your space, remember to layer your lighting. This ensures that your space will have both task and ambient lighting. Coordinating fixtures like sconces, flush mounts, and pendants can help you meet your layered lighting needs and reinforce your desired aesthetic. Install the lights with dimmers that allow you to control the level of light output at any given moment. Get function and style! Browse our site for coordinating lights and expert lighting advice. To help create the perfect look, visit
www.GoldenLighting.com.

Love your light and want to show it off? Follow us, share a picture, and tag us on Social…

How to Identify the Fixture’s Wires

• Hot: Smooth, Black, or Transparent with Black Inner Thread
• Neutral: Ribbed, White or Transparent with White Inner Thread
• Ground: Copper, Bare Metal, Green, or Transparent Inner Thread

IMPORTANT:

• All installation work should be done by accredited professional.
• Shut off power supply at fuse or circuit breaker!
• Use only the specified bulbs. Do not exceed the maximum wattage!

Assembly Instructions

PREPARING FOR INSTALLATION
Carefully remove the new fixture from the carton as well as the yellow bag that holds all of the parts. See the important notes above. Shut off power at the circuit breaker and remove old fixture from wall, including the old mounting strap. (PLEASE NOTE: This fixture has multiple installation options. Before beginning, please review these instructions carefully.) TO INSTALL OVER AN EXISTING JUNCTION BOX AND HARDWIRE THE FIXTURE REFER TO DIAGRAM (1) AND THE SIDE DIAGRAMS WHICH DIFFERENTIATE MOUNTING PLATE (N) FROM MOUNTING BRACKET (B): 1. Mounting plate (N) is attached to backplate (D). To begin, remove mounting plate (B) from backplate (D) so that only mounting bracket (N) is used. Place mounting bracket (N) up against your junction box. Insert mounting screws (A) into the mounting bracket (N). Position the mounting bracket so that the mounting screws (A) are level and parallel with the floor. Use nuts (F) to hold mounting screws (A) in place. 2. Leave at least 8 to 10 inches of fixture wire for wiring. Use a pair of scissors to trim the plug-in cord (P) as shown on the diagram. Pull the cord (P) up through the hole in the bottom of the backplate (D) and plug the hole with stopper (R). 3. Pull the house wires from the junction box through the center of the mounting bracket (N). Secure mounting bracket (N) to the junction box with mounting screws (C) and a screwdriver. Tighten the screws securely. TO INSTALL ON A WALL AND POWER THE FIXTURE USING THE PLUG REFER TO DIAGRAM (2): 1. Mounting plate (B) is attached to backplate (D) already by the factory. To begin, mark the needed holes for securing the fixture. Remove mounting plate (B) from backplate (D). Hold the fixture up to the wall to test placement for backplate (D). After you determine the proper placement, hold mounting plate (B) up to the wall and insert mounting screws (Y) into mounting plate (B) as shown in the diagram, use nuts (F) to hold the screws (Y) in place. Check that the mounting screws (Y) are parallel and level to the floor. Use a pencil to mark the wall through the circular keyholes in the mounting plate (B). 2. Use a drill bit to create two holes on your pencil marks and insert plastic screw anchors (A) into the holes made until the plastic screw anchors (A) are flush with the wall. 3. Align mounting plate (B) with the plastic screw anchors (A). Using a drill or screwdriver, insert mounting screws (C) into the plastic screw anchors (A). Tighten securely.

ASSEMBLING THE FIXTURE

No Assembly Required – This item arrives assembled and ready for installation. Please proceed to the next step.

CONNECTING THE WIRES

IF HARDWIRING THE FIXTURE TO WALL, REFER TO DIAGRAM LABELED “(1)” AND THE WIRING INSTRUCTIONS BELOW. DO NOT FOLLOW THESE WIRING INSTRUCTIONS IF YOU ARE MOUNTING FIXTURE TO THE WALL AND USING PLUG TO POWER FIXTURE, ALSO REFERRED TO AS DIAGRAM LABELED “(2)”. 4. Have an assistant support the fixture’s weight while completing the wiring. Refer to the wiring diagram and attach the fixture’s wires to the power supply wires from the junction box. Attach the fixture’s wires to the power supply wires from the junction box. Connect Hot to Hot (transparent wire with black inner thread, black, or smooth wire) Neutral to Neutral (transparent wire with white inner thread, white, or ribbed wire), and Ground to Ground (transparent wire with green inner thread, green wire, or copper). Twist the ends of the wire pairs together, and then twist on a wire connector. Make sure all twists are in the same direction. If there is no house ground wire coming from the junction box, locate ground screw (E) on the mounting bracket/mounting strap and wrap the fixture’s ground wire around the ground screw. Use a screwdriver to tighten the top of ground screw (E) onto the wires and into the mounting bracket/mounting strap. Tuck the wires into the junction box.

FINISHING THE INSTALLATION

(PLEASE NOTE: This fixture has multiple installation options. Before beginning, please review these instructions carefully.) TO INSTALL OVER AN EXISTING JUNCTION BOX AND

HARDWIRE THE FIXTURE REFER TO DIAGRAM (1):

5. Place backplate (D) over mounting bracket (N) until mounting screws (A) protrude from the holes in backplate (D). Use deco nuts (G) to secure backplate (D) by threading deco nuts (G) onto the exposed threads of mounting screws (A). 6. Refer to the diagram and secure hook (S) onto the fixture arm using small screw (U) and provided tool (T). Tighten small screw (U) until secure and hook (S) is in the preferred position to prevent fixture arm overlap. 7. Take harp fitter (H) and unscrew cap (O) from the threads on top of harp fitter (H). Set cap (O) aside for later. Place the assembled harp fitter (H) into saddle (I) until caps on harp fitter (H) slide down onto saddle (I) to secure. 8. Slide washer (L), shade (M), and washer (N) in the order shown on diagram on top of the exposed threads of harp fitter (H). Use cap (O) to secure washers (L), shade (M), and washer (N) to the harp fitter (H). 9. Install a light bulb (not included) into socket (K) in accordance with the fixture’s specifications. Do not exceed the maximum recommended wattage. Your installation is now complete. 10. Twist knob (Q) clockwise to turn on the fixture. To power the fixture off, twist the knob (Q) counterclockwise.

**TO INSTALL ON A WALL AND POWER THE FIXTURE USING THE PLUG REFER TO

DIAGRAM (2):**

5. Place backplate (D) over mounting bracket (B) until mounting screws (Y) protrude from the holes in the backplate (D). Use deco nuts (G) to secure the backplate (D) by threading deco nuts (G) onto the exposed threads of mounting screws (Y). Take cord (P) from backplate (D) and prepare for the plugin. 6. Refer to the diagram and secure hook (S) onto the fixture arm using a small screw (U) and provided tool (T). Tighten small screw (U) until secure and hook (S) is in the preferred position to prevent fixture arm overlap. 7. Take harp fitter (H) and unscrew cap (O) from the threads on top of harp fitter (H). Set cap (O) aside for later. Place the assembled harp fitter (H) into saddle (I) until caps on harp fitter (H) slide down onto saddle (I) to secure. 8. Slide washer (L), shade (M), and washer (N) in the order shown on diagram on top of the exposed threads of harp fitter (H). Use cap (O) to secure washers (L), shade (M), and washer (N) to the harp fitter (H). 9. Install a light bulb (not included) into socket (K) in accordance with the fixture’s specifications. Do not exceed the maximum recommended wattage. Your installation is now complete. 10. Plug-in cord (P) to your nearest outlet and twist knob (Q) clockwise to turn on the fixture. To power the fixture off, twist the knob (Q) counterclockwise.

Read More About This Manual & Download PDF:

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>