immax ELEGANTE 07165-S Smart LED Ceiling Light with Fan Instruction Manual

immax ELEGANTE 07165-S Smart LED Ceiling Light with Fan

Product Information

• Product Name: ELEGANTE 07165-S Immax NEO LITE ELEGANTE Smart LED ceiling light with fan
• Product Features: Tuya WiFi, silver/wood finish

Components:

• Balancing weight
• Plastic Clip
• Fan motor propeller
• LED module
• Glass cover

Specifications:

• Power: 18W (LED), 70W (fan)
• Luminous Flux: 1500 lm
• Lifespan: 50,000 hours
• Voltage: AC 200-240V, 50-60Hz

Product Usage Instructions

1. To reset the remote control, turn off the fan and then turn it on. Within 30 seconds of turning it on, press and hold the “Fan/on off” button on the remote control for 5 seconds. You will hear a long beep sound, indicating that the remote control has successfully paired with the fan.
2. If the fan is not starting, please follow these troubleshooting steps:
3. Check all fuses or circuit breakers.
4. Turn off electrical power and check all wire connections.
5. Installation Steps:
6. Refer to the user manual for specific installation instructions.
7. Ensure that the balancing weight is properly installed.
8. Attach the plastic clip to the fan motor propeller.
9. Install the LED module and secure it with the glass cover.
10. Make sure all wire connections are properly connected.
11. Follow the provided diagram for the correct placement of components during installation.
12. Consult a professional if needed for proper electrical wiring.

Fan balancing instructions

A ceiling fan can sometimes have a wobble problem caused by blade irregularity or unevenness of the blades.

The following procedure is strongly recommended to correct such a problem.

1. Make sure all blades are screwed tightly to the flywheel, and check the spacing of the blade holders.
2. Check that the fan is firmly installed and the fan does not move during operation. If oscillation persists, dynamic balancing should be performed, using a balancing kit.

Follow the procedure below.

For the fan with ABS blades

• Turn on the fan and set the speed (usually high speed) that causes the worst oscillation.
• Turn the fan off. Remove one blade and place a balancing clip on it. Turn the fan back on and observe whether the oscillation has improved or worsened.
• Turn the fan off again and move the clip to another blade and test again.
• Repeat this procedure with all blades, and then note which blade improved the most with the weight.
• Move the clip back to the vane that showed the greatest improvement.
• On this blade, move the clip to different positions, see where the clip most eliminates fan oscillation.
• Then remove the clip and install a balancing weight in its place.

Reset the remote control:
Turn the fan off and on, and within 30 seconds of turning it on, press the „Fan/on off“ button on the remote control for 5 seconds, after hearing a long „beep“ sound, the remote control has paired with the fan.

TROUBLESHOOTING FAN NOT STARTING

1. Check all fuses or circuit breakers.
2. Turn off electrical power and check all wire connections.

FAN MAKES NOISES

1. Always give any new fan a few days to „break-in“ at medium or high speed.
2. Try to diagnose the exact location of the noise by listening carefully from several sides (blades, motor, light kit, etc.)
3. Check that all bolts in the fan assembly and light kit are tight and screwed in properly. If not, turn off the power and tighten the screws. Tighten these screws at least once a year as they may slowly loosen over time and cause a clicking sound.
4. Make sure the mounting bracket is firmly installed in the junction box.
5. Ensure that the wire nuts in the switch housing or canopy do not snap against each other or the housing wall. If necessary, wrap them with electrician‘s tape.
6. Make sure that the canopy does not touch the ceiling.
7. Ensure that the bolts securing the blade holders to the motor are tight and that the lock washers supplied for this purpose have been used.

THE FAN DOES NOT HEAT THE AIR

1. The fan may run in reverse so that the air is directed upwards.

2. There may be objects in the room that obstruct the airflow.

3. The fan may be too small for the size of the room.
   NOTE FAN QUAKE: A small amount of fan shake is considered acceptable and should not be considered a malfunction.
   WARNING:

   • Never leave the remote control in direct sunlight.
   • Do not throw batteries into a fire, an explosion could occur.

4. CLEANING AND MAINTENANCE

5. Always disconnect the fan from the power source and allow it to stop before cleaning.

6. Make sure the power is turned off at the main fuse or circuit panel before attempting any intervention.

7. Clean the outer surface with a soft damp cloth.

  * Do not allow the internal parts of the product to get wet (especially the circuit board).
  * Do not then immerse the fan in water,
  * Never use wire cloths, abrasive or chemical cleaners.

CAUTION:
THE FAN MUST BE CLEANED OF DIRT AND DUST:

• In the event of a malfunction, do not attempt to repair the fan yourself, there is a risk of fire or electric shock.

WARNING:
Do not use the appliance if its cord, plug or cover is damaged

• The appliance is not intended for use by children under 8 years of age.
• Supervise young children so that they do not play with the appliance. Close supervision by a responsible person is required if the appliance is used by or near children.
• This appliance is not intended for use by persons with impaired physical, sensory, mental or intellectual abilities.
• Do not connect the fan to a dimmer switch.
• The fan must be completely switched off and stopped before changing the direction of the fan. Otherwise, the fan motor and control unit may be damaged.
• Do not attempt to repair the appliance yourself. Contact the official technical support.
• Do not insert any objects into the fan blades during operation. This will damage the fan blades or balance the fan and cause the unit to swing.
• Make sure the fan is not located near curtains, drapes or any objects that could be drawn into the fan.
• Ensure that the installation location does not allow the rotating fan blades to come into contact with any object and that there is a minimum distance of 150 cm from the tip of the blades to the wall. Keep in mind that the greater this distance, the greater the airflow the fan will produce.
• The minimum distance between the fan blades and the floor must be 2.3 m.
• The load capacity of the ceiling or the place where the fan will be suspended must be 45 kg!!!
• Do not use the appliance in confined spaces with explosive or toxic fumes.
• Switch off the power supply before connecting or repairing the fan.
• Electrical wiring must comply with local codes.
• The fan must be properly grounded to avoid the risk of electric shock.
• Never install the fan in a damp or wet room.
• Use caution when moving near the rotating blades..
• To ensure the safety of your children, keep all packaging (plastic bags, boxes, polystyrene, etc.) out of their reach.

INTRODUCTION AND WARRANTY

Thank you for purchasing the product MMAX NEO, to ensure that it serves you best, please read this manual thoroughly and keep it for future reference. The warranty is valid for 2 years from the date of purchase.

The warranty does not cover damage caused by improper installation or abnormal wear and tear. The company does not provide any warranty for surface damage due to improper installation of the product and improper handling of the product. The products are suitable for 6-10 hours of daily operation. Using the product for 24 hours a day would void the warranty. This product is warranted against manufacturing defects only.

INSTALLATION

IMMAX, Pohoří 703, 742 85 Vřesina, EU | www.immax.cz.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>