MOUNT-IT TPM-MA09 Height Adjustable Single Monitor Desk Mount Instruction Manual
- June 4, 2024
- Mount-It
Table of Contents
MOUNT-IT TPM-MA09 Height Adjustable Single Monitor Desk Mount
WARNING!
If you have any confusions or are not quite sure about the installation,
please do not hesitate to ask for our help.
Before assembly, please check and make sure all necessary accessories are
included and undamaged. Improper installation, such as use the product for
monitors over its load capacity or for any purpose not explicitly specified,
may cause damage or serious injury. We would not be liable for any damage or
injury caused by improper mounting or inappropriate use.
The kit contains small items that could be choking hazards if swallowed.
Please keep them OUT OF REACH OF CHILDREN UNDER 3 YEARS OLD. ADULT SUPERVISION
IS REQUIRED.
PACKAGE CONTENTS
ASSEMBLY STEPS
Clamp Installation OR Grommet Base Installation
OPTION A: Clamp Installation
Install the Clamp (C) to the Pole (D) using 3pcs Bolt(G). Tighten using 4mm
Allen key (L). Secure stand to the desktop by tightening the plastic knob or
by using 6mm Allen key (M).
OPTION B: Grommet Base Installation
If existing grommet hole comes with a plastic protector, remove it to ensure a
flat surface before installing the desk mount.
Loosen the screw, separate the clamp (C) into two parts.
Install the Base Plate (J) to the Pole(D）using 1pc of Bolt (G).
Install the pole (D) on the desktop using the support plate (I) and the bolt
separated from clamp(C). Secure stand to desktop by tightening the plastic
knob or by using 6mm Allen key (M).
Arm Installation
Install the wire clip(F) and swivel arm(A and B) to the pole(D).
Fasten the bolt with supplied 6mm Allen key (M) and 3mm Allen key (K)
Attach Monitor
OPTION A: Flat Back Monitor
Attach the VESA plate (E) to back of monitor and secure it with screws (M-A)
or (M-C) and washers (M-E)
using 6 mm Allen Key (M). Do not tighten the screws excessively or it might
damage your monitor.
OPTION B: Curved Back Monitor
Attach the VESA plate (E) to back of monitor and secure it with screws (M-B)
or (M-D) and washers (M-E) and spacers (M-F) using 6 mm Allen Key (M). Do not
tighten the screws excessively or it might damage your monitor.
Hang Monitor
Slide the monitor onto the head of swivel arm, install the security bolt (H). Make sure the security bolt is installed before you rotate the monitor.
Important Notice:
The gas spring is pre-set to minimum tension. Once the monitor is hanged on,
hold the monitor with both hands and DO NOT let go suddenly or immediately.
Instead, leave the monitor in a slow & gentle way while observing whether the
arms will fall down wildly.
Guideline to adjust monitor tilting angle.
Adjust Tension
For intended functioning of the mount, you may need to adjust the tension of Upper Arm (B) in accordance with your monitor weight by 6 mm Allen Key (M).
Note2:
As for how many circles the screw should be turned, refer to below diagram.
Cable Management
Remove Cable Cover
Remove bottom plastic covers from gas spring arm as shown in diagram.
Attach Cable Cover
Run cables from monitor through bottom of gas spring arm. Reattach plastic
covers as shown in diagram.
Adjust as Desired
Adjust monitor position and rotation.
Note: To ensure stability, the tightness of the rotating axis has been preset, so it would be kind of difficult to rotate the VESA plate. Suggestion: Please attach the monitor first, then hold the two sides of it with both hands, and rotate vigorously. If that doesn’t work out, please do not hesitate to ask for our help.
Product Dimensions
CAUTION AND MAINTENANCE:
- Never allow children to climb, stand, hang, or play on any part of monitor or stand.
- This product is intended for indoor use only. Using this product outdoors could lead to product failure and personal injury.
- Check that the bracket is secure and safe to use at regular intervals (at least every three months).
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>