VITEK VTD-TND4FLN-2 Transcendent Series 4 Megapixel Indoor Outdoor IR Network Vandal Dome Camera User Guide

**VITEK VTD-TND4FLN-2 Transcendent Series 4 Megapixel Indoor Outdoor IR Network Vandal Dome Camera User Guide

**

FEATURES

• 1/3” 4.0 Megapixel CMOS Image Sensor

• Up to 30fps @ 4MP (2560 × 1440), 3MP (2304 × 1296), 1080P (1920 × 1080), 720P
  (1280 × 720), D1, CIF, 480 × 240

• 2.8mm Fixed Iris Lens

• Matrix IR with up to 100’ IR Range

• True 120dB Wide Dynamic Range

• True Mechanical Day/Night function by ICR

• XD-DNR (3D & 2D-DNR) Noise Reduction

• Built-in Mic*

• Programmable Analytics: Region Intrusion Detection, Object Removal / Missing, Scene
  Change Detection, Line Crossing, Video Blur, Video Cast Detection

• Compression – Main stream: H.265+ / H.265 / H.264+ / H.264
  Compression – Sub stream: H.265+ / H.265 / H.264+ / H.264 / MJPEG

• MicroSD Card Slot for Local Recording (Up to 256GB)

• Remote Viewing via CMS, Internet Explorer, and iOS & Android Apps

• ONVIF Compliant

• IP67 Weather Resistance + IK10 Impact

• Optional Junction Box (VT-TJB03A), Wall Mount (VT-TWMT3), Pendant Mount (VT-TPDM-1 [reqs. VT-TJB03A]) and In-Ceiling Semi Flush Mount(VT-TFMT-S) Available

• 12VDC & PoE (Power over Ethernet) Operation

• Please research local, state and federal lawsregarding the implementation of audio surveillance

PLEASE NOTE:
Complete User Guide, Software, Tools, and Updates are available online. Scan the QR Code or visit:
http://www.vitekcctv.com/Downloads

Components and Accessories

• Camera

• Quick start guide

• 4 tapping screws PA 4×2

• Rubber plug

• Screwdriver

• Drill template
  

• Plastic plug ×4

Overview

1. Ethernet connector
2. Audio input
3. Power connector
4. Micro SD Card Slot
5. Reset

Cable Connections

First connect the weather resistant cap to an ethernet patch cable, then connect the cameras ethernet adaptor. If not powering the camera with PoE, also connect the power Cable to an approved 12VDC power supply.

Weather Resistant Network Coupler

1. Loosen the nut from the Weather Resistant Network Coupler.
2. Run ethernet cable through coupler, then attach a RJ-45 connector.
3. Tighten the nut and coupler for a weather resistant seal.

Installation

Before beginning installation, make sure that the wall or ceiling is strong enough to withstand 3 times the weight of the camera. The mounting steps are as follows:

1. Attach the drill template to the place where you want to install the camera, then drill the screw holes and 1 cable hole according to the drill template.

1A. Rotate the trim ring counterclockwise to remove

2. Loosen the screws to open the lower dome and then loosen the lock screw to remove the mounting base.
   

3. Route the cables and connect the power & video  cables, use the rubber plug  to fill the gap of the mounting base then secure the mounting base to the celling or wall with screws.
   

4. Before adjusting the three-axis camera mount, preview the camera on a monitor, then adjust as necessary achieve the optimum viewing ang
   

5. 5. Install the lower dome on the camera with the included screws, then put the trim ring back on the lower dome and rotate clockwise until it locks.
   

LAN Configuration

The camera can be accessed on the local network either using the IP-Tool or directly in a web browser

Accessing the Camera Using the IP-Tool

1. Make sure the camera and PC are connected to the LAN.

2. Locate the IP-Tool installer at www.vitekcctv.com/Downloads/Software/Transcendent IPTool_v2.0.2.zip, then install on the PC. Open the installed application.
   

3. Modify the IP address. The default IP address is 192.168.226.201. Click the information of the camera listed in the above table to show the network information on the right side. Modify the IP address and gateway of the camera and make sure its network address is in the same local network segment as the computer’s. Please modify the IP address of your device according to the practical situation.
   For example, the IP address of your computer is 192.168.13.4. So the IP address of the camera shall be changed to 192.168.13.X. After modification, please input the password of the administrator and click “Modify” button to modify the setting

4. Double-click the IP address and then the system will pop up the web 4. Double-click the IP address and then the system will pop up the web control. After downloading, a login window will pop up as shown below
   

Input the user name and password to log in. Default user name: admin / Default password: 123456.

Directly Access Through a Web Browser

The default network settings are as shown below:
IP address: 192.168.226.201 HTTP: 80
Subnet Mask: 255.255.255.0 Data Port: 9008
Gateway: 192.168.226.1
You may use the above default settings when you log in the camera for the first time.

1. Manually set the IP address of the PC. The network segment should be the same as the default settings of IP-CAM. Open the network and share center. Click “Local Area Connection” to pop up the following window.
   Select “Properties” and then select Internet protocol according to the actual situation (for example: IPV4). Next, click “Properties” button to set the network of the PC
   

2. Open the IE Browser and input the default address of IP-CAM and confirm. The IE browser will download Active X control.

3. After downloading Active X control, the login dialog box will pop up.

4. Input the default username and password and then enter to view

WAN Configuration

Access the camera by the router or virtual server for example.

1. Make sure the camera is connected to the LAN; Then log into the camera via LAN and go to System Congfig → Network Config → Port menu to set up the port number.

2. Enter System Config→Network Config→IP Address menu to modify the IP address.
   

3. Go to the router’s management interface through IE browser to forward the IP address and port of IP-CAM in the “Virtual Server
   

4. Open the web browser and input its WAN IP and HTTP port to access the IP-CAM

5. For additional setup, features and functions, please scan the QR code on the front page of this quick guide and download the complete manual.

× 720), D1, CIF, 480 × 2401/3” 4.0 Megapixel CMOS Image Sensor
Min. Illumination| 2.8mm Fixed Iris Lens
Lens| True Day/Night by ICR
Day / Night| 1 Matrix / 100’
IR LEDs / IR Distance| Main stream: H.265+ / H.265 / H.264+ / H.264, Sub: H.265+ / H.265 / H.264+ / H.264 / MJPEG
Video Compression| 60Hz: 4MP/3MP/1080P (1~30fps), 50Hz : 4MP/3MP/1080P (1~25fps)
Main-Stream| 60Hz : 720P(1~30fps)/D1/CIF (1~30fps), 50Hz: 720P/D1/CIF (1~25fps)
Sub-Stream| 64Kbps ~ 8Mbps
Bit Rate| VBR / CBR
Bit Rate Type| Backlight & Highlight Compensati
BLC Control| True WDR (120dB)
Wide Dynamic Range (WDR)| XD-DNR (2D-DNR & 3D-DNR)
Digital Noise Reduction (DNR)| ROI, Saturation, Brightness, Hue, Contrast, Wide Dynamic, Sharpness,
Image Setting| Noise Reduction, etc., Adjustable Through Client Software or Web Browser
Region Intrusion Detection, Object Removal, Scene Change Detection, Line Crossing, Video Blur, Video Cast Detection Motion Alarm, SD Card Error
Analytics| Noise Reduction, etc., Adjustable Through Client Software or Web Brow
Smart Alar| Region Intrusion Detection, Object Removal, Scene Change Detection, Line Crossing, Video Blur, Video Cast Detectio
Region of Interest (ROI)| Each ROI to be Configured Separately
Network| RJ45
Audio| MicroSD Card Slot (256GB)
Storage| CMS / Web Browser / Mobile (iOS/Android)
Remote Viewing| YES
Reset| nternet Explorer (IE) – Plug-in Required, Edge in IE M
Supported Browsers| ONVIF
Connection Protocol| IP67 Weather Rating + IK10
Ingress Protection / Impact Resistance| 12VDC / PoE
Power Input| 12VDC / PoE
Power Consumpt. (12VDC)| 150mA (LEDs Off) / 400mA (LEDs O
Power Consumpt. (PoE)| < 5W
Working Environment| -22°~140°F (-30°~60°C) / Humidity: Less than 95 % non- condensin
Weight Net (Shipping)| 22.58oz / 1.41lb / 640g (28.22oz / 1.65lb / 800g) 3.46 × 4.69” [87.8 × 119mm]
Dimensions (H × Dia)

VT-TJB03A
Optional Junction Box

VT-TFMT-S
Optional Semi-Flush

VT-TWMT3
Optional Wall Mount

VT-TPDM-1
Optional Pendant Mount
– reqs. VT-TJB03A

VT-TPLMT
Transcendent Universal Pole
Mount – reqs.
VT-TJB03A

VT-TCNMT
Transcendent Universal
Corner Mount – reqs.
VT-TJB03A

Transcendent NVRs

A Standalone Solution with
Analytic Support and
NDAA Compliance!

• 8MP (4K)
• HDMI Output
• H.265S / H.265+ / H.265 / H.264 Video Compression
• Analytic Support Including Basic Face Detection, License Plate Recognition, and More!
• Available in 4, 8, and 16 Channels
• Up to 24TB Depending on Model (12TB per HDD)
• PoE Support on ALL Models

Also Consider Vitek NDAA Compliant Wireless Access Points to Reduce Costly Cable Installation!

VT-WAP1150 and VT-WAP2150 High Speed 5.8GHz DIP AP / CPE Wireless Bridge w/ 8MB Storage, 64MB RAM, 150MBps transmission, and Point-to-Multi-Point (P2MP) Topology

With high speed transmission of 150Mbps and a wireless range of 3000ft. (VT- WAP1150) and 1.25 miles (VT-WAP2150) these products eliminate the need for expensive and troublesome longdistance cables in areas where CCTV monitoring and rigorous surveillance take place. These small, lightweight and durable units are easy to install and easy to use with an innovative and straightforward 10-button plug-and-play dip switch that facilitates the creation of a robust wireless network without a computer. Set-up can be simply configured for point-to-point or point-to-multipoint topology depending on the application, with up to 128 IP group configurations!

LIMITED PRODUCT WARRANTY

VITEK products carry a three (3) year limited warranty. VITEK warrants to the purchaser that products manufactured by VITEK are free of any rightful claim of infringement or the like, and when used in the manner intended, will be free of defects in materials and workmanship for a period of three (3) years, or as otherwise stated above, from the date of purchase by the end user. This warranty is nontransferable and extends only to the original buyer or end user customer of a VITEK Authorized Reseller.

The product must have been used only for its intended purpose, and not been subjected to damage by misuse, willful or accidental damage, caused by excessive voltage or lightning.

The product must not have been tampered with in any way or the guarantee will be considered null and void.

This guarantee does not affect your statutory rights.

Contact your local VITEK Reseller should servicing become necessary.

VITEK makes no warranty or guarantee whatsoever with respect to products sold or purchased through unauthorized sales channels. Warranty support is available only if product is purchased through a VITEK Authorized Reseller.

Costumer Support

28492 CONSTELLATION ROAD
VALENCIA, CA 91355
WWW.VITEKCCTV.COM

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>