VITEK VTC-TNT5RMEA Transcendent Series 5 Megapixel Motorized IP WDR Turret Camera User Guide

VITEK VTC-TNT5RMEA Transcendent Series 5 Megapixel Motorized IP WDR

Turret Camera

Product Information

Product Name:
VTC-TNT5RMEA Transcendent Series 5 MegaPixel Motorized IP WDR Turret Camera

Features:

• 5 MegaPixel Motorized IP WDR Turret Camera
• Complete User Guide, Software, Tools, and Updates available online
• Components and Accessories included: Camera, Drill Template, Quick Guide, Rubber Plug, Screws, Waterproof Cap, Hex Wrench
• Ethernet connector
• Audio input connector
• Power connector
• Mounting base
• Locking Screw
• Microphone
• Micro SD card slot

Product Usage Instructions

Network Cable & Power Connections:

1. Connect the Water Resistant Cap to an Ethernet patch cable.
2. Connect the camera’s ethernet adaptor.
3. If not using PoE, connect the power cable to an approved 12VDC power supply.

Weather Resistant Network Coupler:

1. Loosen the nut from the Weather Resistant Network Coupler.
2. Run an ethernet cable through the coupler and attach an RJ-45 connector.
3. Tighten the nut and coupler for a weather-resistant seal.

Installation:

1. Ensure that the wall or ceiling is strong enough to withstand 3 times the weight of the camera.
2. For MicroSD Card Installation: Remove the bottom cover of the camera, insert the card, and replace the cover evenly.
3. Attach the drill template to the desired installation location.
4. Drill 3 screw holes and 1 cable hole (if routing cables through the mounting base) according to the drill template dimensions.
5. Route the cables and connect the power & video cables.
6. Use the rubber plug to fill the gap of the mounting base.
7. Secure the mounting base to the ceiling or wall using screws.
8. Loosen the locking screw and adjust the camera to obtain the optimum viewing angle.
9. Confirm the correct viewing angle with a monitor.
10. Tighten the locking screw to secure the viewing angle adjustments.

LAN Configuration:
The camera can be accessed on the local network either using the IP-Tool or directly in a web browser.

Accessing the Camera Using the IP-Tool:

1. Ensure that the camera and PC are connected to the LAN.
2. Locate and install the IP-Tool application from www.vitekcctv.com/Downloads/Software/Transcendent-IPTool_v2.0.2.zip
3. Open the installed IP-Tool application.
4. Modify the IP address of the camera to match the local network segment of the computer.
5. Input the password of the administrator and click Modify button to save the settings.

FEATURES

• 1/2.7” 5.0 Megapixel CMOS Image Sensor
• Up to 20fps@5MP (2880 × 1620), Up to 30fps@4MP (2560 × 1440), 3MP (2304 × 1296), 1080P (1920 × 1080), 720P (1280 × 720), D1, 480× 240, CIF
• 2.8~12mm Motorized Varifocal Lens
• Matrix IR (up to 165’ IR Range)
• True Wide Dynamic Range (120dB)
• True Mechanical Day/Night function by ICR
• XD-DNR (3D & 2D-DNR) Noise Reduction
• Region Intrusion Detection, Object Abandoned / Missing, Scene Change Detection, Line Crossing, Video Blur, Video Color Cast Detection
• H.265+ / H.265 / H.264+ / H.264 / MJPEG
• MicroSD Card Slot for Local Recording (Up to 256GB)
• 1 Ch. Audio In + Built-in Mic*
• Remote Viewing via CMS, IE (plug-in required)/Google Chrome/Edge/Firefox/Safari, and iOS & Android Apps
• ONVIF Compliant
• IP67 Weather Resistance
• Optional Junction Boxes (VT-TJB01, VT-TJB021), WallMounts (VT-TWM03, VT-TWMT-4) and Pendant Mounts (VT-TPDM-2 [reqs. VT-TJB01], VT-TPDM-3 [reqs. VT-TJB021]) See Additional Mounting Options on Pg. 9
• 12VDC & PoE (Power over Ethernet) Operation
• 3-Year Warranty

Please research local, state and federal laws regarding the implementation of audio surveillance.

Components and Accessories

Overview

1. Ethernet connector
2. Audio input connector
3. Power connector
4. Locking Screw
5. Mounting base
6. Microphone
7. Micro SD c ard slot
8. Reset

Network Cable & Power Connections

First connect the Water Resistant Cap to an Ethernet patch cable, then connect the cameras ethernet adaptor. If not powering the camera with PoE, also connect the power Cable to an approved 12VDC power supply.

Weather Resistant Network Coupler

1. Loosen the nut from the Weather Resistant Network Coupler,
2. Run ethernet cable through the coupler, then attach an RJ-45 connector.
3. Tighten the nut and coupler for a weather-resistant seal.

Installation

Before beginning installation, make sure that the wall or ceiling is strong enough to withstand 3 times the weight of the camera.

MicroSD Card Installation:
Remove the bottom of the cover from the camera, insert card and replace the cover (be sure it is even).

1. Attach the drill template to the place where you want to install the camera, then drill 3 screw holes and 1 cable hole (if you want to route the cables through the mounting base) according to the drill template
2. Route the cables and connect the power & video cables, using the rubber plug to fill the gap of the mounting base, then secure the mounting base to the ceiling or wall with screws (see fig. 2 on next page).
3. Loosen the locking screw, then adjust the camera to obtain the optimium viewing angle. Confirm the correct viewing angle with a monitor. Next, tighten the locking screw to secure the viewing angle adjustments.

LAN Configuration

The camera can be accessed on the local network either using the IP-Tool or directly in a web browser.

Accessing the Camera Using the IP-Tool

1. Make sure the camera and PC are connected to the LAN.

2. Locate the IP-Tool installer at www.vitekcctv.com/Downloads/Soft-ware/Transcendent-IPTool_v2.0.2.zip, then install on the PC. Open the installed application.

3. Modify the IP address. The default IP address is 192.168.226.201. Click the information of the camera listed in the above table to show the network information on the right side. Modify the IP address and gateway of the camera and make sure its network address is in the same local network segment as the computer’s. Please modify the IP address of your device according to the practical situation.
   For example , the IP address of your computer is 192.168.13.4. So the IP address of the camera shall be changed to 192.168.13.X. After modification, please input the password of the administrator and click “Modify” button to modify the setting.

   • Default admin password: “123456″.

4. Double-click the IP address and then the system will pop up the web browser to connect IP-CAM . IE browser will download the Active X control. After downloading, a login window will pop up as shown below:

Input the user name and password to log in.

• Default user name: admin/Default password: 123456.

Directly Access Through a Web Browser

The default network settings are as shown below:

• IP address: 192.168.226.201 HTTP: 80
• Subnet Mask: 255.255.255.0 Data Port: 9008
• Gateway: 192.168.226.1

You may use the above default settings when you log in the camera for the first time.

1. Manually set the IP address of the PC. The network segment should be the same as the default settings of IP-CAM. Open the network and share center. Click “Local Area Connection” to pop up the following window.
   Select “Properties” and then select Internet protocol according to the actual situation (for example: IPV4). Next, click “Properties” button to set the network of the PC.

2. Open the IE Browser and input the default address of IP-CAM and confirm. The IE browser will download Active X control.

3. After downloading Active X control, the login dialog box will pop up.

4. Input the default username and password and then enter to view.

WAN Configuration

Access the camera by the router or virtual server for example.

1. Make sure the camera is connected to the LAN; Then log into the camera via LAN and go to System Congfig→Network Config→Port menu to set up the port number.
2. Enter System Config→Network Config→IP Address menu to modify the IP address.
3. Go to the router’s management interface through IE browser to forward the IP address and port of IP-CAM in the “Virtual Server”.
4. Open the web browser and input its WAN IP and HTTP port to access the IP-CAM.
5. For additional setup, features and functions, please scan the QR code on the front page of this quick guide and download the complete manual.

Specifications

VTC-TNT5RMEA Detailed Specifications

Please research local, state and federal laws regarding the implementation of audio surveillance.

OPTIONAL ACCESSORIES AND RELATED PRODUCTS

OPTIONAL ACCESSORIES AND RELATED PRODUCTS FOR VTC-TNT5RMEA

TRANSCENDENT NVRs

A Standalone Solution with Analytic Support and NDAA Compliance!

• 8MP (4K) HDMI Output
• H.265S/H.265+/H.265/H.264 Video Compression
• Analytic Support Including Basic Face Detection, License Plate Recognition, and More!
• Available in 4, 8, and 16 Channels
• Up to 24TB Depending on Model (12TB per HDD)
• PoE Support on ALL Models

Also Consider Vitek NDAA Compliant Wireless

Access Points to Reduce Costly Cable Installation!
VT-WAP1150 and VT-WAP2150 High Speed 5.8GHz DIP AP / CPE Wireless Bridge w/ 8MB Storage, 64MB RAM, 150MBps transmission, and Point-to-Multi-Point (P2MP) Topology.

With high speed transmission of 150Mbps and a wireless range of 3000ft. (VT- WAP1150) and 1.25 miles (VT-WAP2150) these products eliminate the need for expensive and troublesome long-distance cables in areas where CCTV monitoring and rigorous surveillance take place. These small, lightweight and durable units are easy to install and easy to use with an innovative and straightforward 10-button plug-and-play dip switch that facilitates the creation of a robust wireless network without a computer. Set-up can be simply configured for point-to-point or point-to-multipoint topology depending on the application, with up to 128 IP group configurations!

LIMITED PRODUCT WARRANTY

VITEK products carry a three (3) year limited warranty. VITEK warrants to the purchaser that products manufactured by VITEK are free of any rightful claim of infringement or the like, and when used in the manner intended, will be free of defects in materials and workmanship for a period of three (3) years, or as otherwise stated above, from the date of purchase by the end user. This warranty is nontransferable and extends only to the original buyer or end user customer of a VITEK Authorized Reseller.

• The product must have been used only for its intended purpose, and not been subjected to damage by misuse, willful or accidental damage, caused by excessive voltage or lightning.
• The product must not have been tampered with in any way or the guarantee will be considered null and void.
• This guarantee does not affect your statutory rights.
• Contact your local VITEK Reseller should servicing become necessary.

VITEK makes no warranty or guarantee whatsoever with respect to products sold or purchased through unauthorized sales channels. Warranty support is available only if product is purchased through a VITEK Authorized Reseller.

28492 CONSTELLATION ROAD VALENCIA, CA 91355 WWW.VITEKCCTV.COM.

PLEASE NOTE:
Complete User Guide, Software, Tools, and Updates are available online. Scan the QR Code or visit: http://www.vitekcctv.com/Downloads.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>