Minka Lavery 2452-695 Bishop Crossing 15.5 Inch 2 Light Soft Brass Vanity Light Instruction Manual

Minka Lavery 2452-695 Bishop Crossing 15.5 Inch 2 Light Soft Brass Vanity

Light

Product Information

The product is a light fixture with item number 2452-695 and was manufactured on August 13, 2021. The fixture comes with installation instructions that must be read and saved for future reference. The fixture requires mounting Set#A-021-240112, which includes mounting screws, ground screw, and mounting plate. The fixture is designed to be mounted on a junction box, which is not included in the package. The fixture can accommodate two medium base bulbs with a maximum wattage of 60 watts each or CFL or LED equivalent, which are not included in the package.

Product Usage Instructions

1. Shut off power at the fuse box or circuit breaker box before installing the fixture.
2. Remove the old fixture including the mounting hardware.
3. Unpack the new fixture and lay out all parts in a clear area.
4. Loosen screws (E) to remove mounting plate (A) from fixture body (F).
5. Position mounting plate (A) on the wall and mark the location of two drywall anchors (B). Pre-drill the holes for the drywall anchors (B). Insert drywall anchors (B) into the wall.
6. Attach mounting plate (A) to the junction box using the mounting screws (D). The side of mounting plate (A) marked GND must face out. Place woodscrews (C) through the holes into the drywall anchor (B) to secure mounting plate (A) as shown in Fig.1.
7. Connect the electrical wires as shown in Fig. 2, making sure that all wire connectors are secured. If your junction box has a ground wire (green or bare copper), connect the fixture’s ground wire to it. Otherwise, connect the fixture’s ground wire directly to mounting plate (A) using the green screw provided. After the wires are connected, tuck them carefully inside the junction box.
8. Place fixture body (F) over mounting plate (A) and secure with screws (E).
9. Place shade assembly (J) onto socket stand (G) and secure with screws (I).
10. Install two medium base bulbs (H) up to 60 watts each or CFL or LED equivalent in accordance with the fixture specification. DO NOT EXCEED THE MAXIMUM WATTAGE RATING!
11. Turn on power and test the fixture.

INSTALLATION INSTRUCTIONS

READ AND SAVE THESE INSTRUCTIONS

WARNING! SHUT POWER OFF AT FUSE OR CIRCUIT

MOUNTING THE FIXTURE (Fig.1)

1. Shut off power at the fuse box or circuit breaker box and remove the old fixture including the mounting hardware.

2. Carefully unpack your new fixture and lay out all the parts in a clear area. Take care not to misplace any small parts necessary for installation.

3. Loosen screws (E) to remove mounting plate (A) from fixture body (F).

4. Position mounting plate (A) on the wall and mark the location of two drywall anchors (B). Pre-drill the holes for the drywall anchors (B). Insert drywall anchors (B) into the wall.

5. Attach mounting plate (A) to the junction box (not included) using the mounting screws (D). The side of mounting plate (A) marked “GND” must face out.

6. Place woodscrews (C) through the holes into the drywall anchor (B) to secure mounting plate (A) as shown in Fig.1.
   CONNECTING THE WIRES (Fig. 2)

7. Connect the electrical wires as shown in Fig. 2, making sure that all wire connectors are secured. If your junction box has a ground wire (green or bare copper), connect the fixture’s ground wire to it. Otherwise, connect the fixture’s ground wire directly to mounting plate (A) using the green screw provided. After the wires are connected, tuck them carefully inside the junction box.
   FINISHING THE INSTALLATION (Fig.1)

8. Place fixture body (F) over mounting plate (A) and secure with screws (E).

9. Place shade assembly (J) onto socket stand (G) and secure with screws (I).

10. Install (2) two medium base bulbs (H) up to 60 watts each or CFL or LED equivalent (not included) in accordance with the fixture specification. —DO NOT EXCEED THE MAXIMUM WATTAGE RATING! (NE PAS DEPASSER LA PUISSANCE NOMINALE MAXIMALE!) Your installation is now complete. Return power and test the fixture.

Note: Illustration (Fig.1) on this manual is for installation purposes only. It may or may not be identical to the fixture purchased.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>