SDC 1091ADMR Concealed Mortise Bolt Lock Installation Guide
- June 13, 2024
- SDC
Table of Contents
SDC 1091ADMR Concealed Mortise Bolt Lock
Product Information:
The product is the 1091ADMR (.865 BACKSET) CONCEALED MORTISE BOLT LOCK with MECHANICAL RELEASE FAIL-SAFE (SINGLE CYLINDER PREP) manufactured by SECURITY DOOR CONTROLS. It is designed for use in aluminum or hollow metal doors. The lock features a stainless steel bolt with a 5/8″ bolt throw and a backset of .865. The face plate measures 10-1/2″ x 1-1/2″ x 1/8″ and the strike plate measures 4″ x 1-1/2″ x 1/8″. The lock requires a 1-1/8″ cylinder (not included) and can be used with a standard straight cam ILCO (863G) or equivalent. Please note that dimensional references are subject to change without notice.
Product Usage Instructions
Aluminum Frame Preparation:
- Tap 8 tabs for #10-32 screws on the frame.
- Prepare a cylinder hole with a diameter of 1-1/8″.
Door Preparation:
- Tap 2 holes for #10-32 screws on the door.
Hollow Metal Frame Preparation:
- Tap 8 tabs for #10-32 screws on the frame.
- Prepare a cylinder hole with a diameter of 1-1/8″.
Reversing the Cylinder:
- Remove the Cylinder locking set screw.
- Screw the Cylinder out of the Mounting Block.
- Remove the four screws securing the Mounting Block and the Sliding Link Block.
For any suggestions, comments, or further assistance, please contact SECURITY DOOR CONTROLS through their website or email engineer@sdcsecurity.com.
INSTALLATION INSTRUCTIONS
1091ADMR (.865″ BACKSET) CONCEALED MORTISE BOLT LOCK with MECHANICAL RELEASE FAIL-SAFE (SINGLE CYLINDER PREP)
NOTE: DIMENSIONAL REFERENCE ARE SUBJECT TO CHANGE WITHOUT NOTICE.
TECHNICAL DATA (FOR STANDARD UNIT)
- FACEPLATE: 10-1/2″ x 1-1/2″ X 1/8″
- STRIKE: 4″ x 1-1/2” x 1/8”
- ID REQUIREMENTS: 10-1/2” x 1-1/2” x 1-3/4”
- BOLT: 5/8” DIA. STAINLESS STEEL
- BOLT THROW: 3/4”
- BACKSET: .865″
Any suggestions or comments to this instruction or product are welcome. Please contact us through our website or email engineer@sdcsecurity.com
Hollow Metal Frame Preparation
NOTE: DIMENSIONAL REFERENCE ARE SUBJECT TO CHANGE WITHOUT NOTICE.
TECHNICAL DATA (FOR STANDARD UNIT)
- FACE PLATE: 10-1/2″ x 1-1/2″ X 1/8″
- STRIKE: 4″ x 1-1/2” x 1/8”
- ID REQUIREMENTS: 10-1/2” x 1-1/2” x 1-3/4”
- BOLT: 5/8” DIA. STAINLESS STEEL
- BOLT THROW: 3/4”
- BACKSET: .865″
Door Preparation
NOTE:
DIMENSIONAL REFERENCE ARE SUBJECT TO CHANGE WITHOUT NOTICE.
TECHNICAL DATA (FOR STANDARD UNIT)
- FACE PLATE: 10-1/2″ x 1-1/2″ X 1/8″
- STRIKE: 4″ x 1-1/2” x 1/8”
- ID REQUIREMENTS: 10-1/2” x 1-1/2” x 1-3/4”
- BOLT: 5/8” DIA. STAINLESS STEEL
- BOLT THROW: 3/4”
- BACK SET: .865″
INSTRUCTIONS FOR REVERSING THE CYLINDER
Remove the Cylinder locking set screw, and screw the Cylinder out of the
Mounting Block.
Remove the four screws securing the Mounting Block and the Sliding Link Block.
Make sure the sliding Link Block is aligned properly
LOCK WIRING
Select 24VDC OR 12VDC Configuration, and use provided pigtail connector:
When both options are ordered the Common is shared
SECURITY DOOR CONTROLS ■ WWW.SDCSECURITY.COM
[t] 800.413.8783 ■ 805.494.0622 ■ E-mail:
service@sdcsecurity.com ■ 801 Avenida Acaso,
Camarillo, CA 93012 ■ PO Box 3670, Camarillo, CA 93011
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>