GOLDEN LIGHTING 6073-OFM NB-SS Seabrooke 2 Light Natural Black Outdoor Flush Mount Instruction Manual
- June 12, 2024
- GOLDEN LIGHTING
Table of Contents
GOLDEN LIGHTING 6073-OFM NB-SS Seabrooke 2 Light Natural Black Outdoor
Flush Mount
Product Information
The product is a lighting fixture offered by Golden Lighting. The fixture can be a pendant or linear pendant, chandelier, or sconce and is suitable for use in various spaces such as kitchens, dining areas, and open areas. The fixture should be installed at least 30 inches above the countertop in the kitchen and dining area, and at least 7.5 feet from the floor in open areas. The fixture wires include hot, neutral, and ground wires that are color-coded for easy identification. The fixture arrives fully assembled and ready to install.
Product Usage
To use the product, follow these instructions:
- Identify the location where you want to install the fixture.
- Choose the appropriate fixture for the space based on the recommended installation height and width.
- Identify the location of the electrical box and ensure it is suitable for supporting the weight of the fixture.
- Turn off the power supply to the electrical box.
- Attach the mounting strap (B) to the electrical box using screws (C).
- Connect the fixture wires (hot, neutral, and ground) to the house wires (hot, neutral, and ground) using wire connectors (D).
- Lift the canopy (F) up over the mounting strap (B) and secure it with screws (A) and deco nuts (G).
- Install light bulbs according to the fixture’s specifications.
- Attach rod (I) to post (H) until secure.
- Lift glass shade (J) up to canopy (F) until rod (I) protrudes from the hole in the glass shade (J).
- Secure glass shade (J) in place using washer (K), hex nut (L), cap (M), and finial (N) in the order shown in the diagram.
- Tighten all parts until secure.
- After installing the fixture, apply clear silicone rubber caulking to seal the gap between the enclosure and the mounting surface.
- Turn on the power supply and test the fixture.
For the best lighting results, layer your lighting by coordinating fixtures like sconces, flush mounts, and pendants. Install the lights with dimmers that allow you to control the level of light output at any given moment. For more information on coordinating lights and expert lighting advice, visit www.GoldenLighting.com.
Pendants & Linear Pendants Above a Kitchen Island
Center a linear pendant over the island. If hanging pendants, use one pendant
for every 24″ of island. Fixtures should hang at least 30″ above the
countertop.
Pendants & Chandeliers Above a Dining Room Table
Fixtures should stay at least 30″ above the table. Use a fixture that is 12″
narrower than the width of the table.
Pendants and Chandeliers in Open Areas
The bottom should hang at least 7.5 feet from the floor. Allow clearance for
any opening doors.
We appreciate your business and hope you love your new light!
Great lighting can add value and enhance the look of your home. To ensure the
best lighting in your space, remember to layer your lighting. This ensures
that your space will have both task and ambient lighting. Coordinating
fixtures like sconces, flush mounts, and pendants can help you meet your
layered lighting needs and reinforce your desired aesthetic. Install the
lights with dimmers that allow you to control the level of light output at any
given moment. Get function and style! Browse our site for coordinating lights
and expert lighting advice. To help create the perfect look, visit
www.GoldenLighting.com.
Love your light and want to show it off?
Follow us, share a picture, and tag us on Social…
Assembly Instructions: 6073-OFM
How to Identify the Fixture’s Wires
Hot: Smooth, Black, or Transparent with Black Inner Thread
Neutral: Ribbed, White or Transparent with White Inner Thread
Ground: Copper, Bare Metal, Green, or Transparent Inner Thread Get help,
quick tips, and explore curated content
For Customer Service, contact the place of purchase to arrange for replacement
parts.
IMPORTANT:
- All installation work should be done by accredited professional.
- Shut off power supply at fuse or circuit breaker!
- Use only the specified bulbs. Do not exceed the maximum wattage!
Assembly Instructions:
PREPARING FOR INSTALLATION
Carefully remove the new fixture from the carton as well as the yellow bag that holds all of the parts. See the important notes above. Shut off power at the circuit breaker and remove old fixture from wall, including the old mounting strap.
-
From the parts bag remove the mounting strap (B) assembly. Mounting strap (B) contains several pairs of threaded holes. Find the pair of holes that matches the spacing of the holes on the junction box. Two sets of mounting screws (A & D) should be attached to the mounting strap (B). You may need to tighten nuts (C) that hold mounting screws (A) in place. If the screws are not attached, please hold canopy (F) up to mounting strap (B). Line up the holes in canopy (F) with the holes in mounting strap (B) and insert mounting screws (A) into mounting strap (B) so that mounting screws (A) protrude through the holes in canopy (F). Mounting screws (A) are long, so please test the canopy against the mounting strap to see how far you should insert the screws. Remove the canopy (F) and tighten nuts (C) onto mounting screws (A) to hold the screws in place. Place mounting strap (B) over the junction box. Secure mounting strap (B) to the junction box with mounting screws (D) and use a screwdriver to tighten the screw firmly. Pull house wires from the center of the mounting strap.
ASSEMBLING THE FIXTURE
No Assembly Required – This item arrives assembled and ready for installation. Please proceed to the next step.
CONNECTING THE WIRES -
Have an assistant support the fixture’s weight while completing the wiring. Refer to the wiring diagram and attach the fixture’s wires to the power supply wires from the junction box. Attach the fixture’s wires to the power supply wires from the junction box. Connect Hot to Hot (transparent wire with black inner thread, black, or smooth wire) Neutral to Neutral (transparent wire with white inner thread, white, or ribbed wire), and Ground to Ground (transparent wire with green inner thread, green wire, or copper). Twist the ends of the wire pairs together, and then twist on a wire connector. Make sure all twists are in the same direction. If there is no house ground wire coming from the junction box, locate ground screw (E) on the mounting bracket/mounting strap and wrap the fixture’s ground wire around the ground screw. Use a screwdriver to tighten the top of ground screw (E) onto the wires and into the mounting bracket/mounting strap. Tuck the wires into the junction box.
FINISHING THE INSTALLATION -
Lift canopy (F) up over mounting strap (B) so that mounting screws (A) protrude from the holes in the canopy (F). Thread deco nuts (G) onto the exposed threads of mounting screws (A) until the canopy (F) is secure and snug against the ceiling. 4. Install light bulbs (not provided) in accordance with the fixture’s specifications. Do not exceed maximum recommended wattage. Thread rod (I) to post (H) until secure. Lift glass shade (J) up to canopy (F) until rod (I) protrudes from the hole in the glass shade (J). Secure glass shade (J) in place using washer (K), hex nut (L) cap (M), and finial (N) on the exposed threads of rod (I) in the order shown in the diagram. Tighten until secure. After installing the fixture, apply a clear silicone rubber caulking to seal the gap between the enclosure and the mounting surface. Your installation is complete. Turn on the power and test the fixture.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>