Barrette OUTDOOR LIVING 73050568 Louvered Gate Kit Instruction Manual

: June 12, 2024
: Barrette OUTDOOR LIVING

Table of Contents

73050568 Louvered Gate Kit
BEFORE YOU BEGIN:
TOOLS/MATERIALS NEEDED:
Documents / Resources

LOUVERED GATE KIT
Installation Instructions

REV 3.22

73050568 Louvered Gate Kit

Read all instructions prior to installing product.
Refer to manufacturers safety instructions when operating any tools.
To register your product, please visit: barretteoutdoorliving.com
WARNING:

Improper installation of this product can result in personal injury. Always wear safety goggles when cutting, drilling and assembling the product.
Incorrect installation may cause harm to the gate or individual.
Check local building codes to determine pool-safe fencing options.
Do not allow children to play with the gate.

NOTICE:

DO NOT attempt to assemble the kit if parts are missing or damaged.
DO NOT return the product to the store, for assistance or replacement parts call: 1-877-265-2220.

BEFORE YOU BEGIN:

Vinyl gate posts require an internal support system for weight-bearing purposes therefore a post stiffener is required. Post stiffener needs to be purchased separately.

TOOLS/MATERIALS NEEDED:

| Louvered Fence Boards
---|---
| Phillips Screwdriver
| Safety Glasses
| Line Level
| Tape Measure
| Drill
| #2 Square Drive Bit
| Gate Hardware (Latch)

Component list:

QTY	Description
2	Gate Uprights
1	Top Rail
1	Bottom Rail
4	Upright Inserts
2	Upright Caps
8	Upright Screws
2	Hinges
1	Vinyl Cement

Barrette OUTDOOR LIVING 73050568 Louvered Gate Kit - Assembled Gate
Kit

To obtain and review a copy of the warranty please visit barretteoutdoorliving.com.
You may also contact us at 1-877-265-2220 or email CS.outdoorliving@barretteoutdoorliving.com.

a. Apply provided vinyl cement to all inside surfaces of the uprights where the rails will be installed (Fig. 1).
b. Install top and bottom rails into one gate upright (Fig. 2).
Install all infill boards into gate upright with rails (Fig. 3).
Install final upright insuring that infill boards and rails line up with routes (Fig. 4).
Ensure gate is square. Measure diagonally from top of left corner rail (A) to bottom of right corner rail (B) and note the length. Then, measure diagonally from top of right corner rail (C) to bottom of left corner rail (D). Note the length. Make sure both measurements are the same before installing screws into uprights (Fig. 5).
Install two 6″ screws (provided) through each upright insert and into the rail using the molded grooves on the insert as a guide (Fig. 6).
Install upright caps onto the top of each upright with remaining vinyl cement (Fig. 8).
Attaching Barrette Outdoor Living Hinge
To The Upright:
a. Attaching the hinges to the inside of the gate will allow the gate to open inward. When attaching them to the outside, the gate will swing outward.
b. Mark and pre-drill 3 ⁄32″ pilot holes on top and bottom upright. Secure using six 1 1 ⁄2″ screws (provided with the hinge) to front and side of the upright (Fig. 9). Repeat for the bottom hinge.
Hold the gate level to the post, pre-drill holes with 3 ⁄32″ bit and secure with six 1 1 ⁄2″ screws to the post (Fig. 10). Repeat for the bottom hinge.
NOTE: Use 2″ blocks to align the gate with the fence and help hold the gate steady (Fig. 11).

Barrette Outdoor Living
7830 Freeway Circle, Middleburg Heights, OH 44130
barretteoutdoorliving.com
•877-265-2220
REV 3.22

Documents / Resources

| Barrette OUTDOOR LIVING 73050568 Louvered Gate Kit [pdf] Instruction Manual
73050568, 73040719, 73050571, 73050567, 73050570, 73050568 Louvered Gate Kit, Louvered Gate Kit, Gate Kit
---|---