Pronomic DX-30BTU USB MKII DJ-Mixer User Manual

DX-30BTU USB MKII DJ-Mixer

ArtNr 00059206
Version 01/2022

Important safety instructions

• To protect against personal, third-party, or device damage read the following safety instructions and keep it at home for future reference.
• To avoid damage or electric shock this equipment must be protected from dripping or splashing water and submersion. If water has penetrated pull the mains plug immediately and remove any existing batteries.
• Do not place the device near heat sources such as heaters, stoves, or other heat-radiating objects.
• Avoid mechanical shocks and check the unit regularly for damage to housing, power plugs, and other accessories.
• Use only the accessories and attachments provided and approved by the manufacturer.
• A repair may only be carried out by qualified personnel. Unauthorized modification can affect safety and function.
• Listening at high volumes over a long period of time can lead to impaired hearing.
• The device or packaging may contain small parts that may be swallowed by children or cause suffocation.
• This device contains magnetic materials. If necessary ask your doctor about possible effects on implants such as pacemakers or defibrillators.

Front & back panels

Connections

1. Before using this unit, make sure that the AC Adaptor you plug into the mains supply (21) has the correct voltage.
2.  The unit is supplied with OUTPUT jacks. The OUTPUT jacks (20) are used to connect to your amplifier.
3. The MIC INPUTS (15/16) accept a 6,3 mm connector.
4.  On the rear panel you can find two stereo PHONO/LINE INPUTS (17/18), and 1 stereo LINE INPUT (19). The PHONO/LINE SWITCH (4) enables you to set Channel 1 (17) to phono or line. The PHONO/LINE SWITCH (6) enables you to set Channel 2 (18) to phono or line. The USB/LINE SWITCH (8) enables you to set the input to USB or line (19).
5. Headphones can be plugged into the rear panel mounted HEADPHONE (14) jack.

Operation

1. POWER ON: Once you have made all the equipment connections to your mixer, press the POWER SWITCH (12). The power will turn on and the POWER LED (22) will glow RED.
2. CHANNEL 1: The PHONO/LINE SWITCH (4) allows you to select the PHONO 1/LINE 1 (17) jack to input phono or line level. The CHANNEL SLIDE (5) controls the input level of this channel.
3. CHANNEL 2: The PHONO/LINE SWITCH (6) allows you to select the PHONO 1/LINE 1 (18) jack to input phono or line level. The CHANNEL SLIDE (7) controls the input level of this channel.
4. CHANNEL 3: The MP3/BT/LINE SWITCH (8) allows you to select the USB BLUETOOTH OR LINE 2 CHANNEL (19). The CHANNEL SLIDE (9) controls the input level of this channel.
5. CROSSFADER: The CROSSFADER (10) allows you to mix the sources 1/2 into each other.
6. TALKOVER (3) The purpose of the talkover section is to allow the program playing to be muted so that the mic can be heard above the music. When you switch the TALKOVER SWITCH, the takeover will be on and the volume of all sources except the Mic inputs are lowered by 12 dB. The Micro volume knob (2) allow you to control the level of MIC1/MIC2.
7. Connect your headphones to the headphones socket and select the desired channel (channel 1-3 or MIC) for monitoring with the Cue switch (1). With this knob PHONE (11), you can adjust the headphone’s volume
8. OUTPUT-METER: The OUTPUT-METER (13) indicates either the MASTER output left or right levels.
9. The USB (23) jack can connect to a USB stick.
10. |<< (24): Use this button to re-start the track or to select the previous track.
11. Play/Pause (25): Each time you press this button, the operation changes from play to pause or from pause to play.

12. | (26): Use this button to select the next track.

13. VOL-(27): Use this button to control the level down.
14. VOL+(28): Use this button to control level UP.
15. EQ (29): Allow you to select the effect.
16. LED DISPLAY (30): Display to MP3’s information.
17. BLUETOOTH LED (31): It displays the Bluetooth operating status. When you turn on the power, the Bluetooth LED is flashing slowly which means that it is ready to connect to a Bluetooth device. If no connection is found after 1 minute, the LED goes out and enters into standby mode. If the Bluetooth connection is made with a player, the light flashes slowly, about 2-3 seconds flicker once. At this point you can use the Bluetooth player to play music can hear the music of the corresponding channel. Note: This function is only available on the products with Bluetooth function.

Specifications

MIC 1 & MIC 2 sensitivity……………………………… 1.5 mV (10 K ohms)
PHONO sensitivity ………………………………………… 3mV (47 K ohms)
LINE/CD sensitivity ………………………………. 150 mV (22 K ohms)
MASTER OUTPUT ……………………………………… nominal 775 mV MAX 1.5 V
Frequency Response ………………………………… 20Hz-20KHz ±2dB
Talkover attenuation …………………………………. －12dB
Headphone output ………………………………………. 300mV/8-16 ohms
Bluetooth frequency……………………… 2402-2480 MHz
Max. transmission power..……………………… < 20mW

WEEE Declaration

Your product is designed and manufactured with materials and components of high quality, which are recyclable and can be reused. The symbol means that your product should be disposed of separately from household waste when it reaches its end of life. Please dispose of this equipment at your local collection point or recycling center. Please help to protect the environment in which we all live. All specifications and appearances are subject to change without notice. All information was correct at time of printing. Musikhaus Kirstein GmbH does not guarantee for the accuracy or completeness of any description, photograph or statement contained in this manual. Printed colors and specifications may vary slightly from product. Products from Musikhaus Kirstein GmbH are only sold through an authorized dealer. Distributors and dealers are not agents of Musikhaus Kirstein GmbH and have no authority to bind Musikhaus Kirstein GmbH legally in any way. This manual is protected by copyright. Any copying or reprint, even in excerpts, is only allowed with the written consent of Musikhaus Kirstein GmbH. The same applies to the reproduction or copying of images, even in altered form.

SIMPLIFIED EU DECLARATION OF CONFORMITY
Hereby, Musikhaus Kirstein GmbH declares that the radio Equipment type [Pronomic DX-165REC MKII] is in compliance with Directive 2014/53/EU.
The full text of the EU declaration of conformity is available at the following internet address:
http://www.kirstein.de/docs/Konformitaetserklaerung/CE_Konformitaetserklaerung_00059209.pdf

Musikhaus Kirstein GmbH
Bernbeurener Str. 11
86956 Schongau – Germany
Telefon/Phone: 0049-8861-909494-0
Telefax/Fax: 0049-8861-909494-19

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>