Commercial Electric CD44bRGBW11W Smart Tunable LED Puff Light User Guide
- June 4, 2024
- Commercial Electric
Table of Contents
Commercial Electric CD44bRGBW11W Smart Tunable LED Puff Light
Safety Information
WARNING: PRODUCT MUST BE INSTALLED BY A PERSON FAMILIAR WITH THE
CONSTRUCTION AND OPERATION OF THE PRO0DUCT AND THE HAZARDs INVOLVED, IN
ACCORDANCE WITH THE APPLICABLE INSTALLATION CODE.
Carefully read and understand the information given in this manual before
beginning the assembly and installation. Failure to do so could lead to
electric shock, fire or other injuries which could be hazardous or even fatal.
- Be sure the electricity to the wires you are working on is shut off. Either remove the fuse or turn off the circuit breaker.
- Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment
WARNING:
- Risk of fire or electric shock. Lighting fixture installation requires knowledge of luminaire electrical systems. If not qualified, do not attempt installation. Contact a qualified electrician.
- To prevent wiring damage or abrasion, do not expose wiring to edges of sheet metal or other sharp objects.
- Only use the control provided with or specifiedby these instructions to control this flush mount. This flush mount will not operate properly when connected to a standard (incandescent) dimmer or dimming control.
- NOTICE: Do not make or alter any open holes in an enclosure of wiring or electrical components during installation.
- NOTICE: Any changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
- NOTICE: Not compatible with dimmers. Only can be dimmed by Hubspace App., Google Assistant, Alexa. Dimming range is 5%-100%
FCC Regulation
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with
a minimum distance of 20 cm between the radiator and any part of your body.
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following tw0 conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
Caution: The user is cautioned that changes or modifications not
expressly approved by the party responsible for Compliance could void the
user’s authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uSes,
and can radiate radio frequency energy and, it not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Wireless Protocol
The Wi-Fi CERTIFIEDTM Logo is a certification mark of WI-Fi Alliance®. Apple and the Apple logos are trademarks of Apple, Inc., registered in the U.S., and other countries. App Store is a service mark of Apple Inc. Google, Google Play and the Google Play logo are trademarks of Google LLC.
Warranty
WHAT IS COVERED
The manufacturer warrants this lighting fixture to be free from defects in
materials and workmanship for a period of five (5) years from date of
purchase. This warranty applies only to the original consumer purchaser and
only to products used in normal use and service. If this product is found to
be defective, the manufacturer’s only obligation, and your exclusive remedy,
is the repair or replacement of the product at the manufacturer’s discretion,
provided that the product has not been damaged through misuse, abuse,
accident, modifications, alterations, neglect or mishandling.
WHAT IS NOT COVERED
This warranty shall not apply to any product that is found to have been
improperly installed, set up, or used in any way not in accordance with the
instructions supplied with the product. This warranty shall not apply to a
failure of the product as a result of an accident, misuse, abuse, negligence,
alteration, or faulty installation, or any other failure not relating to
fauity material or workmanship. This warranty shall not apply to the finish on
any portion of the product, such as surface and/or weathering, as this is
considered normal wear and tear. The manufacturer does not warrant and
specifically disclaims any warranty, whether express or implied, of fitness
for a particular purpose, other than the warranty contained herein. The
manufacturer specifically disclaims any liability and shall not be liable for
any consequential or incidental loss or damage, including but not limited to
any labor/ expense costs involved in the replacement or repair of said
product.
Contact the Customer Service Team at
1-877-592-5233 or visit
www.HOMEDEPOT.COM/HUBSPACE.
Pre-Installation
PLANNING INSTALLATION
Read all instructions before assembly. Before starting installation of this
fixture or removal of a previous fixture, disconnect the power by turning off
the circuit breaker or by removing the fuse at the fuse box. To avoid damaging
this product, assemble it on a soft, non-abrasive surface such as carpet or
cardboard.
NOTE: Keep your receipt and these instructions for proof of purchase.
TOOLS REQUIRED
HARDWARE INCLUDED
NOTE: Hardware not shown to actual size.
- AA Wire nut 3
- BB Mounting screw 2
PACKAGE CONTENTS
- A Housing 1
- B Diffuser 1
Installation
Removing the Diffuser
- Hold the Housing (A) of the fixture and rotate the diffuser (B) counterclockwise to remove.
Install Mounting Screws
- Install the mounting screws (BB) onto the junction box (not included) and leave a little gap.
Connect the Wires
- Connect the black and white wires of the fixture with two wires of the same colors from the junction box. Secure together using wire nuts (AA).
- Connect the grounding wire of the fixture with the one from the junction box. Secure together using a wire nut (AA).
Fix the Housing
- Align the keyholes on the housing (A) with the mounting screws (BB). Then rotate the housing (A) to securely fit to the junction box and tighten Screws (BB) to secure.
Install the Diffuser
- Align the slots on the diffuser(B) with buckle point on the inside of housing(A).
- Turn the diffuser(B) clockwise carefully and confirm it locks into place.
Turn on the Light
- Restore power to the junction box.
- Turn the light switch on to activate the fixture.
Operation
-
Download the HubspaceTM app from the App Store or the Google Play Store.
-
Create an account to sign in or log in if you already have an account.
-
Connect your flush mount to power and follow the instructions on the app screen.
-
Tap the +’ button in the upper right corner to add your flush mount.
-
Scan the QR Code
Scan the QR code in the quick start guide or on the flush mount. To scan the QR code on the flush mount, diffuser needs to be removed. Please follow step 1 in the instructions. -
Using Your Smart Flush Mount
- Turn your smart flush mount on or off from the Home page on the Hubspace app.
- To set a schedule or timer, tap the name of the smart flush mount on the Home page. You will see options for setting Schedules and Auto-Off Timers.
-
Set up your Voice Assistant
- You can connect your smart flush mount to Google Home and Alexa from the Hubspace app. Or, you can sign in to Alexa app or Google Home and connect to your Hubspace devices from there.
Care and Cleaning
- Clean the fixture with a soft, dry cloth.
- Do not use any cleaners with chemicals, solvents, or harsh abrasives.
WARNING: Shut off power at the circuit breaker or fuse panel before cleaning the fixture.
Troubleshooting
Compatibility
This lighting fixture is designed to be surface-mounted onto a3 in./4 in.
junction box. Junction box types, sizes, and site conditions vary. Ensure
compatibility with the fit, wiring, and mounting Refer to the information
below:
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>