JONATHAN Y JYL9919 Sophie 38.5 in. 5 Light LED Pendant Instruction Manual

JONATHAN Y JYL9919 Sophie 38.5 in. 5 Light LED Pendant

Product Information

This is a lighting fixture with Model# JYL9919. The product dimensions are W38.5XH2248X6.5”E. The product comes with a mounting plate, canopy, finial, lamp body, long tube, short tube, gasket, nut, wrench, shade, and bulbs. The product requires installation by a licensed electrician. The main electrical supply from the main fuse box/circuit breaker should be switched off before installation. The item should be inspected carefully before attempting to install it. If there is any damage or obvious defect, the item should not be installed. Once installed, the item may not be returned. The estimated assembly time for the product is 20 minutes. The product has specific requirements for connecting the hot and neutral wires based on their cord type and color. The product has grounding instructions for installation in the United States and Canada. The product comes with type B bulbs with a maximum wattage of 40 watts or CFL/LED bulbs with a maximum wattage of 13/9 watts respectively.

Product Usage Instructions

1. Before beginning assembly of the product, ensure all parts are present and undamaged. Do not attempt to assemble the product if any part is missing or damaged.
2. Separate the mounting plate from the canopy by removing the canopy nut anti-clockwise.
3. Fix one end of the finial to the lamp body.
4. Fix the long tube and short tube to the lamp body in turn.
5. Pass one end of the short tube through the canopy, gasket, and nut, and then fix it with a wrench.
6. Attach the mounting plate onto the J-box and secure it by turning 2 mounting screws clockwise till tight. Connect the hot, black, or red outlet supply wire to the black parallel cord (round & smooth) clear, brown, gold, or black without tracer (colored insulated wire not green) copper metal conductor.
7. Connect the neutral, white outlet supply wire to the white parallel cord (square & ridged) clear, brown, gold, or black with tracer (colored stripes) insulated wire (not green) with a silver metal conductor.
8. For installation in the United States, wrap the ground wire from the outlet box around the green ground screw on the mounting bracket. If the fixture is supplied with a ground wire, connect it to the outlet ground wire with a wire connector. For installation in Canada, if the fixture is supplied with a ground wire, wrap it around the green grounding screw on the mounting bracket.
9. Attach the canopy of the lamp body to the mounting plate and fix it by turning the canopy nut clockwise.
10. Install the shade on the lamp cap of the lamp body.
11. Insert the bulbs into the sockets. Be sure to use a light bulb with a wattage no greater than specified on this fixture. Always make sure that the electrical current is turned off before changing bulbs.

WARNING
WE RECOMMEND INSTALLATION OF THIS LIGHTING FIXTURE BE DONE BY A LICENSED ELECTRICIAN.
WARNING *** SWITCH OFF THE MAIN ELECTRICAL SUPPLY FROM THE MAIN FUSE BOX/CIRCUIT

BREAKER BEFORE INSTALLATION

INSPECT THE ITEM CAREFULLY BEFORE ATTEMPTING TO INSTALL. IF THERE IS ANY DAMAGE OR OBVIOUS DEFECT, DO NOT INSTALL. ITEM MAY NOT BE RETURNED ONCE IT HAS BEEN INSTALLED.

• Model#: JYL9919
• Product Dimensions: W38.5”XH22-
• 48” X6.5”E

CARE AND MAINTENANCE

• To clean the outside of the fixture, use a dry or slightly dampened clean cloth (use clean water, never a solvent) to wipe the surface of the fixture.
• To clean the inside of the fixture, first disconnect the power to the fixture by turning off the circuit breaker or by removing the fuse at the fuse box. Next, use a dry or slightly dampened clean cloth (use clean water, never a solvent) to wipe the interior surface of the fixture.
• Do not use any cleaners with chemicals, solvents, or harsh abrasives. Use only dry soft cloth to dust or wipe carefully.

NOTICE& IMPORTANT SAFETY INSTRUCTIONS

• Please make sure that you have all parts indicated before you begin assembly of this item
• This item should be assembled on a soft surface to prevent scratching the finish during assembly
• To reduce the risk of fire, electrical shock, or injury to persons or property, please follow the guideline below for safe use and installation
• The external flexible cable or cord of this luminaire cannot be replaced if the cord is damaged, the luminaire shall be destroyed.

Part List and Hardware List

PREPARATION

• Before beginning assembly of the product, make sure all parts are present. Compare parts with the package contents list and hardware contents list. If any part is missing or damaged, do not attempt to assemble the product.
• Estimated Assembly Time: 20 minutes.

1. Separate the Mounting Plate(I) from the Canopy(E) by removing the Canopy Nut(L) anti-clockwise.
2. Fix one end of the Finial (A) to the Lamp Body (B)
3. Fix the Long Tube (C) and Short Tube (D) to the Lamp Body (B) in turn
4. Pass one end of the Short Tube (D) through the Canopy (E), Gasket (F), Nut(G), and then fix it with Wrench (H)
5. Attach the Mounting Plate ( I ) onto the J-box and secure it by turning 2 Mounting Screws (K) clockwise till tight.

Connect, Hot, Black, or Red Outlet Supply Wire to:| Connect, Neutral, White Outlet Supply Wire to:
---|---
Black| White

• Parallel Cord (round & smooth)| * Parallel Cord (square & ridged)
  Clear, Brown, Gold, or Black without Tracer (colored| Clear, Brown, Gold, or Black with Tracer (colored stripes)
  Insulated Wire (not green) with a copper metal conductor| Insulated Wire (not green) with Silver metal conductor.

Grounding Instructions

• For installation in the United States: Wrap ground wire from the outlet box around the green ground screw on the mounting bracket, no less than 2″ from the wire end. Tighten the ground screw. If the fixture is supplied with a ground wire, connect to the outlet ground wire with a wire connector.
• For installation in Canada: If the fixture is supplied with ground wire, wrap ground wire around the green grounding screw on the mounting bracket. Tighten the ground screw.
• Attach the Canopy of the Lamp body(B) to the Mounting Plate ( I ) and fix it by turning the Canopy Nut (L) clockwise.
• Install the Shade (M) on the lamp cap of the Lamp Body (B)
• Insert the bulbs (N) into the Sockets. Be sure to use a light bulb(M) with a wattage no greater than specified on this fixture. Always make sure that the electrical current is turned off before changing bulbs.

PLEASE USE TYPE”B” BULB MAX 40-WATT OR CFL BULB MAX 13-WATT OR LED MAX 9-WATT THERE ARE 5 X 4W LED BULBS IN THE BOX. ENJOY YOUR LAMP

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>