Honeywell SNG-S SERIES Hall-Effect Speed Sensor Instruction Manual

Honeywell SNG-S SERIES Hall-Effect Speed Sensor

GENERAL SPECIFICATIONS

Honeywell’s SNG-S Series Speed Sensors use a magnetically biased Hall-effect integrated circuit (IC) to accurately sense movement of ferrous metal targets. The specially designed IC and a permanent magnet are sealed in rugged, probe- type packages. The IC detects the alteration of the magnet’s flux density when it is approached by ferrous metal. A sensor positioned at the circumference of a revolving gear wheel detects the teeth and spaces, and supplies a digital pulse output with frequency proportional to gear wheel speed. Optimum performance is dependent upon a combination of variables such as target material, geometry and speed, sensor/target gap, and environmental temperature.

ELECTRICAL SPECIFICATIONS

TABLE 1. ELECTRICAL SPECIFICATIONS

CHARACTERISTIC

|

CONDITION/COMMENT

| PARAMETER

SNG-SPRF-002

| SNG-SPRD-002 SNG-SPSC-001 SNG-SPRC-001| SNG-SPRD-003 SNG- SPRC-002| SNG-SPRD-004 SNG-SPRC-003
Supply voltage| regulated supply and 12 V battery ISO 16750-2| 4.5 V to 24 V

—

| —

8 V to 16 V

| —

4.8 V to 16 V

| —

4.8 V to 24 V

Supply current| —| 20 mA max.| 15 mA
Reverse voltage protection| —

ISO 16750-2

| -24 V

—

| —

-14 Vdc

Over voltage protection| —

ISO 16750-2

| 26.5 V

—

| — 26 V
Short circuit protection| —

ISO 16750-2

| 16 V

—

| — 16 V
Load dump| ISO 16750-2:2012 11 01

(US* = 40 V, UA 13.5 ±0.5 V)

| 5b

—

|  | —

—

|
Insulation resistance| ISO 16750-2:2012| >10 MOhm at 500 Vdc

—

| —

—

MECHANICAL SPECIFICATIONS

TABLE 2. MECHANICAL SPECIFICATIONS

CHARACTERISTIC

| PARAMETER

SNG-SPRF-002

| SNG-SPRD-002 SNG-SPSC-001 SNG-SPRC-001| SNG-SPRD-003 SNG- SPRC-002| SNG-SPRD-004 SNG-SPRC-003
Carrier material| PBT thermoplastic| PBT
Bushing material| SS304| SSTL
O-ring material| 70 durometer fluorocarbon, PTFE coating 17,0 mm ID x 2,0 mm CS| fluorocarbon, brown 17,0 mm ID x 2,0 mm CS
Housing material| PBT| PBT
Connector: integral mating|

Bosch 928000453

Bosch 1928403966

|

Amp Superseal 1.5

282087

Mounting torque| 8 ±0,5 N m with M6 screw| 20 ±3 N m with M8 screw
O-ring lubrication| mineral oil-based grease

ENVIRONMENTAL SPECIFICATIONS

TABLE 3. ENVIRONMENTAL SPECIFICATIONS

CHARACTERISTIC

|

CONDITION/COMMENT

| PARAMETER
SNG-SPRF-002| ALL OTHER CATALOG LISTINGS

Radiated immunity

| ISO 11452-2: 2004

ISO 11452-2: 2004

IEC 61000-4-3: 2008

ISO 11452-2, 400 MHz to 2.5 GHz

| 10 kHz to MHz, 60 m/V

200 MHz to 2.7 GHz, 100 V/m

800 kHz MHz to 1000 MHz, 3 m/V

—

| —

—

—

100 V/m

Bulk current injection| ISO 11452-4, 1 MHz to 400 MHz| 100 mA
ESD| SAE J1113/13 ISO 10605| ±4 kV contact, ±8 kV air

—

| —

±8 kV contact, ±15 kV air

Conductive transients| ISO 7637-2, for 12 V system

ISO 7637-2, for 12 V system

| TEST PULSE 1, 2a, 2b, 3a, 3b

—

| —

PULSE 1, 2a, 3a, 3b, 5a

Conducted emissions| CISPR 25. 150 kHz to 108 MHz| —| Class 3
Radiated emissions| CISPR 25. 150 kHz to 12.5 GHz| —| Class 3
Thermal cycle| -40°C to 140°C| —| 100 cycles

Humidity

| —

95 %RH at 55°C

| 10 %RH to 90 %RH at -40°C to 85°C,

150 cycles, 600 hr total

—

| —

144 hr, EN/IEC 60068-2-30

Saline dunk| 0°C to 110°C| —| 10 cycles, ISO 16750-4

Salt fog

| 5% salt solution by mass at 35°C and 93% RH for 400 hr, tested to 2000 hr with no ingress in the sensor packaging area

5% salt solution by mass at 35°C

| 5% salt solution by mass at 35°C and 93% RH for 2000 hr

—

|

—

96 hours

Combined temperature and vibration test

| sinusoidal: 25 hr/axis, 3 perpendicular axes

30 g at 60 Hz to 1000 Hz and 15 g at

1000 Hz to 2000 Hz

random: 25 hr/axis, 3 perpendicular axes 30 g at 25 rms Hz to 2000 Hz, -40°C to 125°C

| sinusoidal: 25 hr/axis, 3 perpendicular axes

15 g at 5 Hz to 2000 Hz

random: 25 hr/axis, 3 perpendicular axes

at 25 grms at 10 Hz to 2000 Hz

|

—

—

Vibration| 3 perpendicular axes, 48 hr per axis| —| 29.8 GRMS, 24 Hz to 2000 Hz, MIL-STD-202-214
Degree of protection| IEC 50629

IEC 60529

| IPX6, IPX9K, IPX7

—

| —

IP69K, IP67

Resistance to fluids| —| —| general under-the-hood automotive fluids
Operating temperature| —| -40°C to 150°C| -40°C to 140°C
Storage temperature| —| -55°C to 70°C| -40°C to 140°C

SCHEMATIC DIAGRAMS AND OUTPUT SPECIFICATIONS

Output signal: high

low

|

—

—

|

VP – 0.5 V

<0.6 V

Load current| output leakage current -10 mA| 10 mA max.
Frequency| —| 0 kHz to 10 kHz

kOhm) 0.3 V to 2.2 V

low| target orientation| <(((VP-0.4) x 1 k)/(1 k + Rp
 |  | in kOhm))+0.4
Load current| —| 15 mA
Frequency| —| 0 kHz to 10 kHz

controller interface

| >VCC – 0.5 V
low|  | <0.5 V
Load current| —| 20 mA
Frequency| —| 0 kHz to 10 kHz

Output signal: high

low

|

dependent on the controller interface

|

(Vp x (16.5)/(16.5+ Rp in

kOhm)0.5 V

<0.5 V

Load current| —| 20 mA
Frequency| —| 0 kHz to 10 kHz

MOUNTING DIMENSIONS

(FOR REFERENCE ONLY: MM/[IN].)

CUSTOMER INTERFACE BORE

WARNING
PERSONAL INJURY
DO NOT USE these products as safety or emergency stop devices or in any other application where failure of the product could result in personal injury. Failure to comply with these instructions could result in death or serious injury.

WARRANTY/REMEDY

Honeywell warrants goods of its manufacture as being free of defective materials and faulty workmanship during the applicable warranty period. Honeywell’s standard product warranty applies unless agreed to otherwise by Honeywell in writing; please refer to your order acknowledgment or consult your local sales office for specific warranty details. If warranted goods are returned to Honeywell during the period of coverage, Honeywell will repair or replace, at its option, without charge those items that Honeywell, in its sole discretion, finds defective. The foregoing is buyer’s sole remedy and is in lieu of all other warranties, expressed or implied, including those of merchantability and fitness for a particular purpose. In no event shall Honeywell be liable for consequential, special, or indirect damages.
While Honeywell may provide application assistance personally, through our literature and the Honeywell web site, it is buyer’s sole responsibility to determine the suitability of the product in the application.
Specifications may change without notice. The information we supply is believed to be accurate and reliable as of this writing. However, Honeywell assumes no responsibility for its use.

FOR MORE INFORMATION

Honeywell Safety and Productivity Solutions services its customers through a worldwide network of sales offices and distributors. For application assistance, current specifications, pricing or the nearest Authorized Distributor, visit our website or call:

USA/Canada +1 302 613 4491
Latin America +1 305 805 8188
Europe +44 1344 238258
Japan +81 (0) 3-6730-7152
Singapore +65 6355 2828
Greater China +86 4006396841

Honeywell
Advanced Sensing Technologies
830 East Arapaho Road
Richardson, TX 75081
sps.honeywell.com.ast

References

• Safety and Productivity Solutions | Honeywell
• Products - Advanced Sensing Technologies | Honeywell

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>