Einhell FREELEXO LCD BT+ 3413984 Robot Lawn Mower Instruction Manual

: June 17, 2024
: Einhell

Einhell FREELEXO LCD BT+ 3413984 Robot Lawn Mower

Einhell-FREELEXO-LCD-BT+-3413984-Robot-Lawn-Mower-
PRODUCT

Product Specifications

Model: FREELEXO LCD BT+
Art.-Nr.: 34.139.80
I.-Nr.: 21043

Product Usage Instructions

Safety Instructions

Read the user manual for safety instructions and warnings before operating the robot lawn mower.

Technical Data

Begrenzungsdrahtkabelantenne Betriebsfrequenzband: 0-148,5 KHz
Bluetooth-Verbindung Betriebsfrequenzband: 2400-2483,5 MHz
Netzteil Eingangsspannung: 100-240 V ~ 50/60 Hz

Inbetriebnahme

Ensure there are no obstacles in the operating area before starting the robot lawn mower.

Connecting the Charging Station

Connect the power supply (13) to the charging station (19) as shown in Figure 5c.

Installation of Boundary Wire on Inclines

When installing the boundary wire on slopes, ensure a minimum distance of 0.8m.
Connect objects to create a common boundary island if necessary (see Figure 6h).

Handling Obstacles

If an obstacle is detected, the robot lawn mower will navigate around it.
Ensure the area is clear of any hindrances for efficient operation.

Frequently Asked Questions (FAQ)

Q: How can I tell if the battery is fully charged?

A: All 3 LEDs will light up when the battery is fully charged.
If only 1 LED blinks, it indicates that the battery is low and needs recharging.
Danger! – Read the operating instructions to reduce the risk of injury.
Children are not allowed to use this equipment. This equipment can be used by people with limited physical, sensory, or mental capacities or those with no experience and knowledge if they are supervised or have received instruction on how to use the equipment safely and understand the dangers that result from such use.
Children are not allowed to play with the equipment.
Children are not allowed to clean the equipment or carry out user-level maintenance work.

Danger!

When using the equipment, a few safety precautions must be observed to avoid injuries and damage. Please read the complete operating instructions and safety regulations with due care.
Keep this manual in a safe place, so that the information is available at all times. If you give the equipment to any other person, hand over these operating instructions and safety regulations as well.
We cannot accept any liability for damage or accidents that arise due to a failure to follow these instructions and the safety instructions.

Safety regulations

The corresponding safety information can be found in the enclosed booklet.

Warning!

Read all the safety information, instructions, illustrations, and technical data provided on or with this power tool.
Failure to adhere to the following instructions may result in electric shock, fire, and/or serious injury.
Keep all the safety information and instructions in a safe place for future use.

Explanation of the symbols used

(see Fig. 14)

A. WARNING – Read the operating instructions before you start using the machine.
B. WARNING – Keep a safe distance away from the machine when it is in operation.
C. WARNING – Always actuate the locking mechanism before carrying out any work on the machine or before lifting the machine.
CAUTION – Do not touch rotating blades
D. WARNING – Do not ride on the machine.
CAUTION – Do not touch rotating blades
E. Protection class II (double-insulated)
F. Store the battery only in dry rooms with an ambient temperature of +10°C to +40°C.
Place only charged batteries in storage (charged at least 40%).
G. Protection class III
H. Slow fuse 2 A
I. For use in dry rooms only.
J. WARNING: To charge the battery, use only the removable power supply unit NT24/1 / PS24/1 delivered with this tool.

Important!

Always pull out the power plug and disconnect the perimeter wire from the charging station during a storm.

Layout and items supplied

Layout (Fig. 1/2)

Robot lawn mower
Control panel
STOP button/release button for the display cover
Cutting height adjustment facility
Rain sensor
Carry-handle
Main switch
Rear wheel
Battery compartment cover
Blades
Blade plate
Front-wheel
Power supply unit (cable)
Fastening peg
Fastening screw
Cable connector
Spare blades
Perimeter wire
Charging station
Charging pin
LED indicator
Hexagon key
Display cover
USB connection
Ruler (for detaching)

Items supplied and unpacking

Please check that the article is complete as speciﬁ ed in the scope of delivery.
If parts are missing, please contact our service center or the sales outlet where you made your purchase at the latest within 5 working days after purchasing the product and upon presentation of a valid bill of purchase.
Also, refer to the warranty table in the service information at the end of the operating instructions.
Open the packaging and take out the equipment with care.
Remove the packaging material and any packaging and/or transportation braces (if available).
Check to see if all items are supplied.
Inspect the equipment and accessories for transport damage.
If possible, please keep the packaging until the end of the guarantee period.

Danger!

The equipment and packaging material are not toys.
Do not let children play with plastic bags, foils, or small parts.
There is a danger of swallowing or suﬀ ocating!
Scope of delivery, assembly material, and accessories (some not included):
Details of the scope of delivery can be found in the enclosed related information sheet.
Robot lawn mower
Power supply unit (cable)
Charging station
Fastening screws (4 pcs)
Spare blades
Fastening pegs
Perimeter wire
Cable connectors
Hexagon key
Rechargeable battery
Charger
Ruler (for detaching)
Original operating instructions
Safety information

Required aids (not supplied)

Hammer
Pair of pliers
Wire stripper
Spirit level (optional)

Intended use

The robot lawn mower is intended for private use, i.e. for use in home and garden environments and only for mowing lawns.
The equipment is allowed to be used only for its prescribed purpose. Any other use is deemed to be a case of misuse. The user/operator and not the manufacturer will be liable for any damage or injuries of any kind resulting from such misuse.
Please note that our equipment has not been designed for use in commercial, trade, or industrial applications. Our warranty will be voided if the equipment is used in commercial, trade, or indust-rial businesses or for equivalent purposes.

Technical data

Voltage ……………………………………………….. 18 V
Motor speed ………………………………….. 3500 rpm
Protection . …………………………………………….IPX4
Protection class .. ………………………………………..III
Weight ………………………………………………..8.0 kg
Cutting width . ………………………………………18 cm
Number of blades … ……………………………………. 3
Max. gradient .. …………………………………….. 35%
Sound power level LWA ………………………. 57 dB(A)
Uncertainty K ……………………………….. 2.3 dB (A)

Cutting height

adjustment ………. 20-60 mm; infinitely adjustable
Permissible length of perimeter wire …………………………..max. 250 m

Perimeter wire cable antenna

Operating frequency band .. …………. 0-148.5 KHz
Maximum transmission power . ……67.05 dBuA/m

Bluetooth connection

Operating frequency band …….2400-2483.5 MHz
Maximum transmission power ……………-2.2 dBm

Power supply unit

Input voltage: . ……………… 100- 240 V ~ 50 /60 Hz
Output voltage: .. ………………………………. 24 V DC
Output current: .. ……………………………………1.5 A
Protection class: . ……………………………………II /
Sound values were measured per the standards EN ISO 3744:1995 and ISO 11094: 1991.

Warning!

This equipment generates an electromagnetic field during operation. Under certain circumstances, this field may actively or passively impede medical implants.
To reduce the risk of serious or fatal injuries, we recommend persons with medical implants to consult their doctor and the manufacturer of the medical implant before using the equipment.

Starting up

Read the operating instructions fully before you start work on the installation of the robot lawn mower.
The quality of the installation work determines how effectively the robot lawn mower works later on.

How it works

The robot lawn mower chooses its direction on a random basis. The robot lawn mower works its way over every area that is enclosed within the perimeter wire (18) so that the entire garden gets mowed.
Whenever the robot lawn mower detects a correctly installed perimeter wire (18), the robot lawn mower turns about and drives in a different direction within the area.
All zones that you wish to protect within the lawn area – e.g. garden ponds, trees, furniture, or ﬂower beds – must be cordoned off by the perimeter wire (18).
The perimeter wire (18) must form a closed circuit. If the robot lawn mower bumps into an obstacle within the mowing area, it reverses and then continues mowing in a different direction (Fig. 3).

Sensors

The robot lawn mower is equipped with many safety sensors.

Lifting sensor:

If the robot lawn mower is raised at the back by more than 30° from the ground or if a front wheel (12) loses contact with the ground, the robot lawn mower and the rotation of the blades (10) will be stopped immediately.

Tilting sensor:

If the robot lawn mower tilts severely in any direction, the robot lawn mower and the rotation of the blades (10) are stopped immediately.

Obstruction sensor:

The robot lawn mower can detect obstacles in its path. If the robot lawn mower collides with an obstacle, the robot lawn mower and the rotation of the blades will be stopped immediately and the mower will reverse away from the obstacle.

Rain sensor:

The robot lawn mower is equipped with a rain sensor (5) to prevent the robot lawn mower from operating in the rain.
The robot lawn mower returns to the charging station (19) when it detects rain and is completely recharged there.
Once the rain sensor (5) is dry again, the robot lawn mower will stay in the charging station (19) for another two hours.
Only then will it begin working again, provided it is still in an active time window.
If the rain sensor (5) has been activated (this is recommended to exert less stress on the lawn), you will see a bright cloud in the display (50).
If the sensor triggers, a dark cloud with raindrops will appear. Do not short-circuit the two metal sensors with metal or any other conductive material.
This will impede the correct operation of the robot lawn mower.

Preparations

First, sketch your lawn. Include obstacles in your sketch and draw up a plan for how you intend to protect them.
This will make it easier to ﬁnd a good position for the charging station (19) and to lay the perimeter wire (18) around bushes, ﬂower beds, etc. (Fig. 4).
If the grass is taller than 60 mm it has to be shortened ﬁrst to avoid exposing the robot lawn mower to excessive load and adversely affecting its operating efficiency.
Use a conventional lawn mower or trimmer to do this. Remove all loose objects from the lawn that could get damaged by the robot lawn mower or damage the robot lawn mower itself.
Have the following tools ready: A hammer, tongs, a wire stripper, and a spirit level (optional).

Fitting the battery

A battery (A) from the Power-X-Change series is needed to operate the robot lawn mower.
Important: Depending on the model of your robot lawn mower, it might not come complete with the battery (A).
Open the battery compartment cover (9). Press the pushlock button of the battery (A) and push the battery (A) into the mount provided.
Close the battery compartment cover (9) and make sure that it latches in place correctly (Fig. 10).
To remove the battery (A), open the battery cover (9). Press the push lock button of the battery (A) and pull out the battery (A).

Charging station

Position of the charging station Determine the best position for the charging stations ﬁrst (19). An outdoor socket outlet is required which supplies a permanent supply of electricity so that the robot lawn mower works at all times.
The charging station (19) must be placed on a ﬂ at area at the level of the turf. Make sure that the area is ﬂ at and dry. Select a position that is in the shade, because it is best if the rechargeable battery is charged up in a cool area.
Also, note that the perimeter wire has to be laid in a straight line for at least 2 m in front of the charging station (19) (Fig. 5a).
Curves immediately in front of the charging station (19) could cause problems when docking for charging.
Localization of the charging station When the rechargeable battery is almost empty, the robot lawn mower returns to the charging station (19) by following the perimeter wire (18) in a counterclockwise direction until it reaches the charging station (19).
Make sure, therefore, that the charging station (19) faces in the right direction when you position it. (Fig. 5b)

Connecting the charging station to the

Before you connect the charging station (19) to the power supply, check that the main po-wer supply is 100-240 V at 50/60 Hz.
Connect the power supply unit (13) directly to a socket outlet. Do not use the cable for any other use.
Do not use the power supply unit if it is damaged (13). In the event of any damage to cables or the power supply unit (13), contact an authorized professional immediately for replacement.
Do not charge up the robot lawn mower in a damp location. Do not charge up the robot lawn mower at temperatures above 40°C or below 5°C.
Keep the robot lawn mower and the power supply unit (13) away from water, sources of heat, and chemicals. Keep the cable of the po-wer supply unit (13) away from sharp edges to prevent damage.
Connect the power supply unit (13) to the charging station (19). (Fig. 5c)

To charge up the rechargeable battery for the robot lawn mower straight away while you are still doing the installation work, ﬁrst switch on the robot lawn mower with the main switch (7) and place the robot lawn mower in the charging station (19).

Information about charging

The robot lawn mower returns to the charging station (19) in each of the following situations.
You send the robot lawn mower back manually.
The battery charge level drops below 30%.
The end of the daily work time has been reached.
The rain sensor has tripped.
The robot lawn mower has become overheated.
Boundary cut“ mode or „Spot mowing“ mode was started outside the set work window and has been completed by the robot lawn mower.
In these cases, the robot lawn mower automatically runs along the perimeter wire (18) until it reaches the charging station (19).
When the robot lawn mower wants to return to the charging station (19), it will ﬁrst look for the perimeter wire (18) and then move along the perimeter wire (18) in a counter-clockwise direction.
The LED indicator (21) on the charging station (19) lights up red while charging of the rechargeable battery is in progress.
When the LED indicator (21) on the charging station (19) turns green, this indicates that the rechargeable battery is fully charged.
Once it has been fully charged, the robot lawn mower resumes operation or remains in the charging station until the next work time window (19).
If there is an obstacle on the perimeter wire (18) during the trip back to the charging station (19), the robot lawn mower will come to a stop in front of the obstacle after several attempts and will not be able to get back to the charging station (19).
Remove all obstacles on the perimeter wire (18). If the temperature of the rechargeable battery exceeds 45°C, charging will stop to prevent damage to the rechargeable battery.
Charging resumes automatically once the temperature has dropped again.
If the temperature of the controller of the robot lawn mower exceeds 65°C, the robot lawn mower will return to the charging station (19).
Operation resumes per the settings once the temperature has dropped again.
If the rechargeable battery becomes empty before the robot lawn mower has returned to the charging station (19), it will not be possible for the robot lawn mower to start up again.
Bring the robot lawn mower back to the charging station (19) and leave the main switch (7) switched on. The robot lawn mower will be charged up automatically.

Perimeter wire

IMPORTANT! Severed perimeter wires and consequential damages are not covered by the warranty!

Laying the perimeter wire

The perimeter wire (18) can be laid both on the ground and in the ground. The fastening can break when hammered in if the ground is hard or dry.
Water the lawn before installing the perimeter wire if the ground is very dry.

Installation on the ground

Lay the perimeter wire (18) securely on the ground and fasten it with the supplied fastenings if you do not intend to scarify or aerate the lawn any time later.
You can still adjust the position of the perimeter wire again during the first few weeks of using the robot lawn mower. After a certain time, however, the perimeter wire will become overgrown with grass and no longer visible.
Install the perimeter wire with a maximum distance of 1 m between fastening
Reduce the distance between the fastening pegs on uneven areas of the lawn. Avoid situations in which the wire is not actually on the ground. Make sure that the perimeter wire cannot be severed by the robot lawn mower.

Installation in the ground

Bury the perimeter wire in the ground at a depth of up to 5 cm. This will prevent the perimeter wire (18) from getting damaged during scarifying or aeration, for example.

Important!

Keep a reserve of 1 m of wire at the rear end of the charging station so that you can make corrections at a later time.

Narrow points

If the lawn has a narrow point, your robot lawn mower will be able to operate there as long as the corridor has a width of at least 1.4 m (80 cm between the perimeter wires) and a maximum length of 8 m. (Fig. 3).
Distance to the garden perimeter When the robot lawn mower approaches a peri-meter wire (18), the perimeter wire is detected by the sensors in front of the robot lawn mower.
Before the robot lawn mower turns about, however, it runs over the perimeter wire (18) by up to 30 cm. Please bear this in mind when planning your mowing area. (Fig. 6a)

Laying the wire in corners

Avoid laying the perimeter wire (18) at a right angle (90°) in corners. To make sure that the robot lawn mower does not run too far beyond the perimeter wire (18), lay the perimeter wire (18) as shown in Fig. 6b.
Calculating the gradient of the lawn The robot lawn mower can cope with gradients of up to 35%. You therefore need to avoid steeper gradients.
The gradient can be determined by the basis of the height divided by the distance. (Fig. 6c)
Example: a/b = 35 cm/100 cm = 35%

Installation of the perimeter wire on gradients

The robot lawn mower can slip on gradients, especially if the grass is wet, and run over the perimeter wire (18) as a result.
It is therefore recommendable to pay attention to the following points (Fig. 6d):
In the area at the top of a slope, the perimeter wire (18) should not be installed on gradients over 35%. Make sure that a distance of 30 cm from obstacles and the edges of the lawn is maintained.
In the area at the bottom of a slope, the perimeter wire (18) should not be installed on gradients over 17%. Make sure that a distance of 40 cm from obstacles and the edges of the lawn is maintained.

Driveways and paved paths

Cordon off raised pathways, areas surfaced with gravel or containing bark mulch, lower-lying beds, or other similar areas. Lay the perimeter wire (18) at a distance of at least 30 cm away. (Fig. 6e and 6g) Paths that are flush with the turf do not need to be cordoned off, because the robot lawn mower can simply run over them. You can also lay the perimeter wire (18) over paths. (Fig. 6f and 6g)

Perimeter islands

To protect obstacles in the mowing area, create perimeter islands. This will enable collisions with delicate objects, garden ponds, trees, furniture, ﬂ ower beds, etc., to be avoided. (Fig. 6h and 6i)
Roll out the perimeter wire (18) from the edges to the objects you want to protect.
Secure the perimeter wire (18) with fastening pegs (14) in a clockwise direction around the object you want to protect.
Completely enclose the perimeter islands and then run the perimeter wire (18) back to the point at which you left the edge of the lawn.
Perimeter islands need to be at least 0.8 m apart. Alternatively, combine the objects to make them into a joint perimeter island. (Fig. 6h)
The perimeter wires (18) to and from the perimeter island should be laid parallel and very close to one another.
Caution! Perimeter wires (18) must not cross over! – You should therefore fasten both the parallel peri-meter wires (18) to the ground together using the same fastening (Fig. 6i)
The robot lawn mower will run over the two parallel perimeter wires (18) in the mowing area, but the robot lawn mower will stop when single perimeter wires (18) are laid.

Obstacles

Obstacles with a height over 10 cm (Fig. 6j)
Solid obstacles that are over 10 cm in height, e.g. trees, walls, fences, garden furniture, etc., are detected by the collision sensors.
If the robot lawn mower collides with an obstacle, it will stop, switch off the mower unit, reverse, and turn so that it can continue mowing in the other direction. Soft, unstable, and valuable obstacles need to be protected by a perimeter wire island.

Stones and low obstacles

Stones, rocks, and low obstacles of less than 10 cm in the mowing area need to be protected because otherwise, the robot lawn mower could run over them.
If not, this could result in the robot lawn mower getting damaged or blocked.

Trees (Fig. 6k)

The robot lawn mower treats trees as obstacles. However, where any tree roots project above the ground to a height of less than 10 cm, the area in which they are located needs to be protected.
This will prevent damage to the roots and the robot lawn mower. Make sure that the minimum distance between the perimeter wire (18) and the obstacle is 30 cm.

Main area and secondary area (Fig. 6l)

A secondary area (B) designates a work area that is not directly connected to the main area (A), e.g. via a stretch of lawn or a path.
To create a separate secondary area (B) lay the perimeter wire (18) from the main area (A) to the secondary area (B) and back again.
The perimeter wire (18) to and from the secondary area (B) should be laid such that the return run is parallel and very close to the forward run.
Caution! Perimeter wires (18) must not cross over each other!
You should therefore fasten the parallel perimeter wires (18) to the ground jointly using the same fastening.
To be able to mow the secondary area (B) you must carry the robot lawn mower by hand into the secondary area (B). Start the required mowing program and select “Secondary area” in the sub-menu (see „Settings of the robot lawn mower“).
When the robot lawn mower is in the secondary area (B) it will not try to follow the perimeter wire (18) towards the charging station (19) if the battery charge level is low.

Connecting the charging station

Finish laying the complete perimeter wire (18) before you connect it to the charging station. Keep an extra length of 1 m of perimeter wire (18) at each end so that you can make further adjustments at a later time.
Using a wire stripper, remove a length of 10 to 15 mm of the insulation at the ends of the perimeter wire (18) for connecting to the charging station (19).
Pull out the power plug before you connect the perimeter wire (18) to the charging station (19). The perimeter wire (18) laid to the front end of the charging station (19) must be run to the back via the cable holders on the underside of the charging station (19).
Connect this perimeter wire (18) to the connection on the left (black). Then pass the rear perimeter wire (18) through the hole (stress-relief) in the connection area and connect it to the connection on the right (red) (Fig. 7a).
Important! Perimeter wires (18) must not cross over!
Then connect the power supply. The LED indicators (21) on the charging station (19) should light up green and stay on permanently.
If the LED does not light up, check the connections ﬁrst. If the LED lights up green but not permanently, read the “Indicators on the charging station and troubleshooting” table at the end of these operating instructions.

Switching on and checking the installation

As soon as the LED indicator (21) on the charging station (19) lights up green, the mowing area is ready for the robot lawn mower.
Please check ﬁrst that all the fastening pegs (14) on the perimeter wire (18) have been fully tapped in.
Place the robot lawn mower about 3 m to the rear of the charging station (19) in front of the perimeter wire (18).
The robot lawn mower needs to be facing the perimeter wire (18) at an angle of 90° (Fig. 7b). Switch on the main switch (7) (ON) (Fig. 8).
Unlock the robot lawn mower by entering the PIN (see the section “Locking mechanism / PIN”).
Press the “MODE“ button (52). Then use the navigation buttons (55) to select the point “Back to station” and conﬁ rm with the “OK“ button (56). Press the “START” button (53) and then close the display cover (23).
The robot lawn mower will now follow the perimeter wire (18) in a counterclockwise direction. Observe the robot lawn mower during the complete trip along the perimeter wire (18) until it is back in the charging station (19).
If the robot lawn mower has any problems at any point, correct the perimeter wire (18) if necessary and repeat the operation. The rechargeable battery of the robot lawn mower will now be fully charged.
If any problems occur with docking, you may need to reposition the charging station (19) sideways until docking works without any problems.
To stop the robot lawn mower at any time, press the red STOP button (3).
When you press the STOP button (3), the robot lawn mower will come to a stop and wait for further instructions.

Securing the charging station

Once the robot lawn mower is working properly and a suitable position for the charging station (19) has been found, the charging station (19) must be ﬁxed in place using the fastening screws (15).
Use the hexagon key (22) to secure the fastening screws (15) fully in the ground. (Fig. 7c)

Battery charge level indicator

Press the button for the battery charge level indi-cator. The battery charge level indicator indicates the charge state of the battery employing 3 LEDs (Fig. 13b).

All 3 LEDs are lit:

The battery is fully charged.

2 or 1 LED(s) are lit:

The battery has an adequate remaining charge.

1 LED ﬂashes:

The battery is empty, recharge the battery.

All LEDs blink:

The battery temperature is too low. Remove the battery from the equipment, and keep it at room temperature for one day.
If the fault reoccurs, this means that the rechargeable battery has undergone exhaustive discharge and is defective. Remove the battery from the equipment.
Never use or charge a defective battery.

Important!

When using a multi-Ah pack (e.g. 4-6Ah), always set the higher capacity. Thanks to the gentle charging and discharging of the robot lawn mower there is no need to use the lower capacity to extend the working life.

Charging the rechargeable battery with the charger

In normal operation, the battery (A) of the robot lawn mower is charged via the charging station (19).
For independent use of the battery (A) from the Power-X-Change series it can also be charged in the external Power-X-Charger.
Important! – Depending on the model of your robot lawn mower, it might not come complete with the battery charger (Fig. 13a/Item B).

Check that your mains voltage is the same as that marked on the rating plate of the battery charger. Insert the power plug of the charger (B) into the socket outlet. The green LED will then begin to ﬂ ash.
Insert the rechargeable battery (A) into the battery charger (B) (Fig. 13a).
In the section entitled „Charger indicator, “ you will ﬁnd a table with an explanation of the LED indicator on the charger.

The rechargeable battery can become a little warm during the charging. This is normal.

If the battery pack fails to charge, check:

whether there is voltage at the socket outlet
whether there is good contact at the charging contacts
If the battery pack still fails to charge, send
the charger
and the battery pack to our customer service center.
To ensure that items are properly packaged and delivered when you send them to us, please contact our customer service or the point of sale at which the equipment was purchased.
When shipping or disposing of batteries and cordless tools, always ensure that they are packed individually in plastic bags to prevent short circuits and ﬁres.
To ensure that the battery pack provides long service, you should take care to recharge it promptly. You must recharge the battery pack when you notice that the performance of the device drops.
Never allow the battery pack to become fully discharged.
This will cause it to develop a defect.

Operation

Main switch

The robot lawn mower is equipped with a main switch (7). Use the main switch (7) to switch the robot lawn mower on (ON) and off (OFF) (Fig. 8).
Once the robot lawn mower has been switched on, it is locked by a PIN.

Control panel

The robot lawn mower has already been programmed at the factory and default settings have been made for it. However, these can be changed if required.
Even though the factory settings will be suitable for most gardens, you should still familiarize yourself with the available options nevertheless.

Explanation of the control panel with LCD

(Fig. 9)

50. LCD
51. “SET” button
52. “MODE” button
53. “START” button
54. ”BACK” button
55. Navigation buttons
56. “OK” button

Cutting height adjustment facility

Important! Adjust the cutting height only when the robot lawn mower has been switched off. Do this by pressing the STOP button (3).
The cutting height adjustment facility (4) allows the cutting height of the robot lawn mower to be set to infinitely adjustable settings between 20 and 60 mm, which can be viewed on the scale.
If the grass is taller than 60 mm it has to be shortened to a maximum of 60 mm first to avoid exposing the robot lawn mower to excessive load and adversely affecting its operating efficiency.
Use a conventional lawn mower or trimmer to do this.
After installation has been completed, the cutting height can be adjusted using the cutting height adjustment facility (4).
Always start with a higher cutting height and reduce it in small steps until you reach the desired height.

Locking mechanism / PIN

The locking mechanism prevents the unauthorized use of the robot lawn mower without a valid code.
You have to enter a personal four-digit security code for this.

Lock release

Before you start using the robot lawn mower, you have to enter the correct PIN (standard PIN: “0-0- 0-0”).
Enter the PIN with the help of the navigation buttons (55).
Standard PIN: New PIN: 0 0 0 0

Changing the PIN

To change the PIN, proceed as follows.

Unlock the control panel.
First press the “SET” button (51) to make your settings.
Use the navigation buttons (55) to navigate in the menu on the LCD (50) to the point “General information” and then „PIN code”.
First, enter the current PIN (standard PIN 0-0- 0-0) with the help of the navigation buttons (55).
Then use the navigation buttons (55) to enter your PIN.
Confirm the settings you have just made.
Repeat step 5. and step 6 in order to confirm the new PIN.
Important! Make a note of the new PIN.

Requesting your PIN if you lose it

Have the receipt and the serial number of the robot lawn mower ready. You need them to get your PIN.

Version A:

Press and hold the „SET” button (51) for 6 seconds in locked status.
The PUK will now appear in the display (50).
Contact the customer services team to obtain your PIN.

Version B:

Connect an empty USB stick to the USB connection (24) as shown (Fig. 11).
Switch on the main switch (7) (ON).
The robot lawn mower will automatically save the PUK to your USB stick and will then end the operation with a beep.
Pull out the USB stick. Import the data from the USB stick to a computer. A text file (*.txt) will have been created by the robot lawn mower. This file contains a PUK, a personal code. Please contact the customer services team to obtain your PIN.

Settings of the robot lawn mower

The main menu on the LCD (50) shows you the current date and time settings of the robot lawn mower, as well as the current charge level.
At the same time, the status of the rain sensor the wire signal, and the selected mowing program will appear in the toolbar.
On the control panel, you can use either the “SET” button (51) to make settings on the robot lawn mower or the “MODE” button (52) to start the robot lawn mower with various mowing programs.
Use the navigation buttons (55) to go to the option where you want to make the settings. Press the “BACK” button (54) to exit the respective menu.

Making settings with the “SET” button (51)

The “SET” button (51) can be used to make the basic settings on your robot lawn mower.
Use the navigation buttons (55) to move to where you want to go and then use the “OK” button (56) to confirm or the “Back” button (54) to discard the settings you have made.

Schedule

Use the navigation buttons (55) to move to the day of the week for which you want to make the settings. In normal operating mode, the robot lawn mower will automatically begin to mow your lawn at the set time on the respective day.
It is recommended to base the mowing time setting on 8 hours per day for 500 m² as a guideline. The selected working time may need to be adapted to take account of the garden’s size and complexity.

Zone

Where gardens have lots of angles, the robot lawn mower may have problems reaching every part of the lawn and mowing it completely.
In this case, you can select several starting points on the perimeter wire (18). This will enable the robot lawn mower to get to even those parts of your garden that are difficult to reach.
The robot lawn mower will run the selected distance along the perimeter wire (18) and then start mowing in this part of the garden (Fig. 6m). ****
Use the navigation buttons (55) to go to the point that you wish to change and enter the distance and frequency accordingly.
The charging station (19) is automatically defined as starting point 1. The two other starting points can be selected as you wish. For this, you must measure the distance between the charging station (19) and the starting point in a clockwise direction along the perimeter wire (18). With the frequency setting, you decide how often the robot lawn mower starts its work from the charging station (19) or the respective starting points.

Boundary cut

For a tidy lawn edge, you can activate the Edge mowing” setting. You can also set the lawn mowing frequency, i.e. the rhythm in which you want the edge of the lawn to be mowed at the beginning of the work window.
In the standard setting, the robot lawn mower will begin work on all 7 work days by first mo-wing along the entire perimeter wire.

Error log

From here you will be informed about the latest error messages concerning your robot lawn mower.

Rain sensor

The rain sensor (5) can be programmed using this setting. The default factory setting for the sensor is “On”.
You can activate or deactivate the rain sensor (5) and set its delay time. The delay time defines how long the robot lawn mower continues to remain in the charging station (19) after the rain sensor (5) has dried.

Leaving the station

You can set how far and where the robot lawn mower travels when it reverses out of the charging station (19). First, the robot lawn mower reverses the set distance before it turns into the area to be mowed or towards its starting point.
Make sure that the set reversing di-stance does not cause the robot lawn mower to leave the area to be mowed.

General

PIN code: You can replace the default PIN for the robot lawn mower with your own choice of PIN. To do so, proceed as described in the chapter “Locking mechanism / PIN”. Important! Make a note of the new PIN.
Date & Time: Use the navigation buttons (55) to go to the point that you want to change and make the settings accordingly.
Language: Use the navigation buttons (55) to activate the language that you want.
Software version: The current version of the robot lawn mower software is noted here.

Mowing programs – “MODE” button (52)

Use the navigation buttons (55) to go to the mowing program that you want to start.
You can always choose between the “Main area” and “Secondary area”.
More details of the two areas can be found in the section “Before using for the ﬁrst time” under “Perimeter wire”.

Mowing

When you start the robot lawn mower to mow the lawn, the mower will switch to normal operating mode with the set schedule.

Boundary cut

Place the robot lawn mower close to the perimeter wire (18) or start the mower while it is in the charging station (19).
With its mower unit activated, the robot lawn mower will follow the perimeter wire (18) in a counter-clockwise direction until it reaches the rear of the charging station (19).
Provided no work window is active, the robot lawn mower will then return to the charging station (19).

Spot mowing

Your robot lawn mower can fail to mow some spots sufficiently. Place the robot lawn mower at the spot in question and start the mower.
The robot lawn mower will begin to mow the lawn in a spiral pattern until it collides with an obstacle or the perimeter wire (18).
Provided no work window is active, the robot lawn mower will then return to the charging station (19).

Back to station

Send your robot lawn mower back to the charging station (19). The robot lawn mower will look for the perimeter wire (18) and follow it counter-clockwise to the charging station (19).
The secondary area option does not exist in this case.

Controlling the robot lawn mower Starting procedure

Press the “STOP” button (3) and open the display cover (23) fully.
Unlock the control panel (2).
Use the“MODE” button (52) to select the mowing program and the respective work area you want.
Press the “START” button (53).
Close the display cover (23).
- The robot lawn mower will now operate under the mowing time setting. During work time the battery charge level will appear on the LCD (50).
- Whenever the battery charge level drops to 30%, the robot lawn mower will return automatically to the charging station (19).

Canceling the mowing operation

1. To bring the robot lawn mower to an immediate stop, press the STOP button (3).
Open the display cover (23) fully.
Unlock the control panel (2).
Press the “MODE” button (52) and select Back to station” to send the robot lawn mower along the perimeter wire (18) and back to the charging station (19).
Press the “START” button (53).
Close the display cover (23).

STOP status:

When you press the STOP button (3), the robot lawn mower will adopt a STOP status. This will be indicated in the LCD (50). The robot lawn mower will interrupt its mowing until this STOP status is canceled.
When the control panel (2) is unlocked, a window will appear and ask if you want to cancel the STOP status. If you conﬁ rm, the status will be canceled. If you don’t conﬁ rm, the robot lawn mower will remain stopped.
If the robot lawn mower is started or returned to the charging station (19), the STOP status will be canceled likewise. Close the display cover (23).

Control of the robot lawn mower using the app

All settings that you can make using the control panel can also be made using the app.
To do so, ﬁrst download the Einhell app for robot lawnmowers to your smartphone.
The Einhell app is available via the following link and QR code:
iOS:http://qr.einhell.com/12e103ce
Android:http://qr.einhell.com/176c0443
Use a Bluetooth connection to connect the robot lawn mower with your smartphone and follow the steps shown there.

Instructions concerning the Bluetooth con-nection:

Connect to the robot lawn mower in the Ein-hell App after you have logged in as the user and registered the unit.
In the case of Android units, you must get approval of the location for the Einhell App to use the Bluetooth connection.
Connect the robot lawn mower only through the Einhell App on your smartphone.
Use the Einhell app to establish a connection to the robot lawn mower.
The range of a Bluetooth connection is limi-ted. This means you must stay close to the robot lawn mower to control it.
The robot lawn mower can be connected to only one smartphone at a time.
Disconnect the Bluetooth connection once you have made all the settings on the robot lawn mower.

Cleaning, maintenance, and ordering spare parts

Hazard!

The equipment must be disconnected from the power supply (pull out the power plug and switch oﬀ the equipment by the main switch (7) (OFF) (Fig. 8) before performing any cleaning and maintenance work.
Also, take the battery out of the robot lawn mower.

Caution! Wear work gloves!

Cleaning

Keep all safety devices, air vents, and motor housing free of dirt and dust as far as possible. Wipe the equipment with a clean cloth or blow it down with compressed air at low pressure.
Do not clean the robot lawn mower with running water, particularly with high-pressure water.
Clean the equipment regularly with a damp cloth and some soft soap. Do not use cleaning agents or solvents; these may be aggressive to the plastic parts in the equipment.
Ensure that no water can get into the interior of the equipment.
For best results, clean the robot lawn mower with a brush or rag.
Check the freedom of movement of the blades (10) and the blade plate (11)
Use cleaning products for metal or very fine abrasive paper to clean the charging contacts on the robot lawn mower (1) and the charging station (19). Clean them to ensure efficient charging.

Maintenance

Worn or damaged blades (10) and their fastening screws must always be replaced as a set.
Replace excessively worn or damaged parts immediately.
To ensure that you enjoy the equipment for many years to come, all screwed parts, as well as the wheels and axles should be cleaned and lubricated.
Keeping your robot lawn mower in good condition not only ensures a long lifespan and high performance but also enables the equipment to thoroughly cut your grass with minimal effort.
The blades (10) are subject to more wear and tear than any other component. Therefore, routinely check the condition of the blades (10) and make sure that they are tightly fastened.
An excessively vibrating robot lawn mower can indicate that the blades (10) are damaged or have become deformed from striking an object. If the blades (10) are worn or damaged, they must be replaced immediately.
Check the appearance of the cut lawn at regular intervals. The grass will not be cleanly cut if the blades are not sharp. This can result in the surface of the lawn drying out easily and turning brown.
It is important therefore to change the blades regularly to obtain a clean and straight cut.
Check the bottom of the robot lawn mower for dirt at regular intervals. Clean your robot lawn mower regularly. Remove heavy soiling immediately.
Heavy soiling of the robot lawn mower is possible in the first weeks of using it for the first time after a conventional law mower had previously been used.
In these first few weeks, you should check the bottom of your robot lawn mower more often.
Shorten the lawn only in small steps to prevent heavy soiling.
There are no other parts inside the equipment which require maintenance.

Replacing the blades

Only replace the blades with genuine blades, as this will ensure top performance and safety. The robot lawn mower is equipped with three blades (10) ﬁtted to a blade plate (11).
These blades (10) have a service life of up to 3 months (if they do not strike any obstacles).
Please replace all three blades (10) at the same time to ensure that there is no possibility of any impairment to the efficiency and balance of your equipment.
To change the blades (10), proceed as follows (Fig. 12) – Caution! – Wear work gloves:

Use a screwdriver to block the rotation of the blade plate (11). Do this by inserting the screwdriver through the holes in the blade plate (11) and the protective ridge.
Undo the fastening screws
Remove the blades (10) and replace them with new ones. Always replace all three blades (10) as a set.
Then retighten the fastening screw. Check that the new blades (10) can rotate freely.

Perform a general inspection of the robot lawn mower at regular intervals and remove any deposits that may have accumulated. At the start of each season, ensure that you check the condition of the blades (10).
If repairs are necessary, please contact our customer service center. Use only genuine spare parts.

Software update

If you want to update the software, copy the new software to an empty USB stick (format the USB stick ﬁrst if necessary). Make sure that the rechar-geable battery is fully charged before you carry out the following steps.

Place the robot lawn mower in the area to be mowed. The robot lawn mower must not be in the charging station during the software update.
Connect a USB stick to the USB connection as shown in the illustration. (Fig. 11).
Switch on the main switch (7) (ON).
The robot lawn mower will now start updating the software and will display the current status.
Pull out the USB stick and restart the robot lawn mower with the main switch (7).

Repairing the perimeter wire

If the perimeter wire (18) gets severed at any point, use the supplied cable connectors (16) to repair it.
To do so, insert both ends of the severed perimeter wire (18) into the cable connector (16) and squeeze it together with the help of a pair of pliers.
Connect the power plug to the socket outlet.
Then check whether it is working properly by checking the LED indicator (21) on the charging station (19).

Ordering spare parts

Please provide the following information when ordering spare parts:
Type of unit
Article number of the unit
ID number of the unit
Spare part number of the required spare part For our latest prices and information please go to www.Einhell-Service.com
Replacement blades Art. No.: 34.140.20

Storage

Fully charge up the rechargeable battery before putting it into storage over winter and switch the robot lawn mower at the main switch (7) (OFF). Take the rechargeable battery out of the equipment.
Disconnect the power supply unit (13) from the power supply and the charging station (19).
The perimeter wire (18) can be left outdoors over winter. However, make sure that the connections are protected against corrosion.
To do so, disconnect the connections of the perimeter wire (18) from the charging station (19).
Store the equipment and accessories out of children‘s reach in a dark and dry place at above freezing temperature.
The ideal storage temperature is between 5 and 30°C. Store the equipment in its original packaging.

Transport

Switch off the equipment at the main switch (7) (OFF). (Fig. 8).
Fit the shipping protectors, if any.
Protect the machine from damage and the strong vibrations that can occur particularly when transporting in vehicles.
Secure the machine against slipping and tipping over.
Carry the robot lawn mower by the carry handle (6) with the blade plate (11) facing away from your body.

Disposal and recycling

The equipment is supplied in packaging to prevent it from being damaged in transit. The raw materials in this packaging can be reused or recycled. The equipment and its accessories are made of various types of material, such as metal and plastic.
Never place defective equipment in your household refuse. The equipment should be taken to a suitable collection center for proper disposal. If you do not know the whereabouts of such a collection point, you should ask your local council oﬃces.

Disposal

Power tools, rechargeable batteries, accessories, and packaging should be sorted for environmentally friendly recycling.
Do not dispose of power tools and batteries/rechargeable batteries into household waste!

Only for EU countries:

According to the Directive 2012/19/EU on waste electrical and electronic equipment and its transposition into national law, power tools that are no longer usable, and, according to the Directive 2006/66/EC, defective or drained batteries must be collected separately and disposed of in an environmentally correct manner.
If disposed of incorrectly, waste electrical and electronic equipment may have harmful effects on the environment and human health, due to the potential presence of hazardous substances.

Only for the United Kingdom:

According to The Waste Electrical and Electronic Equipment Regulations 2013 (SI 2013/3113)
(as amended) and the Waste Batteries and Accumulators Regulations 2009 (SI 2009/890) (as amended), products that are no longer usable must be collected separately and disposed of in an environmentally friendly manner.
The reprinting or reproduction by any other means, in whole or in part, of documentation and papers accompanying products is permitted only with the express consent of Einhell Germany AG.
Subject to technical changes

Indicators on the charging station and troubleshooting

LED indicator (21)	Description	Solution
Oﬀ	– No power supply	– Check the power supply
Lit up green	– Ready for mowing

– Rechargeable battery is fully charged

– Perimeter wire (18) connected

Indicators on the robot lawn mower and troubleshooting Fault messages of the robot lawn mower in the LCD (50)

Fault	Possible cause	Remedy
No signal	– Perimeter wire is not properly connected

– No power supply

– The perimeter wire (18) is severed

| Check whether the LED indicator (21) at the charging station (19) is lit up green

– Make sure that the perimeter wire (18) has been laid correctly and centrally under the charging station (19)

– Check the position of the charging station (19)

Outside border| – Perimeter wire is not properly connected

– The robot lawn mower is outside the mowing area

| – Make sure that the perimeter wire (18) has been laid correctly and centrally under the charging station (19)

– Check that the robot lawn mower is inside the mowing area

Battery error| – There is a battery error on the robot lawn mower

– The rechargeable battery does not charge up

– The rechargeable battery has reached the end of its service life

| – Make sure that the rechargeable battery has been correctly fitted

– Check whether the main switch (7) is ON while the robot lawn mower is in the charging station (19)

– Check the position of the charging station

(19) Replace the rechargeable battery if necessary.

Fault	Possible cause	Remedy
Battery temperature error	The temperature of the rechargeable battery is too

high/low or the controller is overheated

– If the battery temperature exceeds 65°C, the robot lawn mower will return to the charging station (19)

– If the battery temperature seeds 45°C or drops below 0°C, charging will be stopped and the robot lawn mower will wait at the charging station (19)

| Set the work time in summer to the early hours of the morning and avoid running the robot lawn mower during the hours of the day when it is hot

– After the rechargeable battery or controller has cooled down to the permissible temperature range, the robot lawn mower automatically returns to programmed operation

Mower lifted| – The lifting sensor has been continually tripped for 10 se- seconds| Press the STOP button (3) to open the display cover (23). Restart the mowing operative in the control panel (2):

– If this fault occurs frequently, check the mowing area for obstacles taller than 10 cm and either remove them or cordon them oﬀ from the mowing area with peri-meter wire (18).

Mower blocked| – The obstruction sensor has tripped several times within one minute

– The obstruction sensor has been constantly activated for 10 seconds

– The obstruction sensor has tripped three times on the way back to the charging station (19)

| Press the STOP button (3) to open the display cover (23). Restart the mowing operation via the control panel (2):

– Check whether the robot lawn mower is blocked by an obstacle or jammed

between trees, bushes, etc. Remove the obstacle or avoid this area.

– If this fault occurs frequently, check how the perimeter wire (18) has been laid. Pay particular attention to tight angles, corridors, fences, rocks, etc., and adjust the layout of the perimeter wire (18) if necessary.

– Check whether the grass is too tall and the robot lawn mower gets blocked. If this is the case, mow the grass with a conventional law mower to below 60 mm.

Fault	Possible cause	Remedy
Too close to the garage	– The robot lawn mower was sent back too close to the
charging station (19).	Press the STOP button (3) to open the display cover

(23). Re-start the mowing operation on the control panel (2):

– The robot lawn mower should be sent back to the charging station (19) at a minimum distance of 2 m.

Rolling over| – The robot lawn mower was constantly tilted for 10 se- seconds

– The robot lawn mower has been tilted for a prolonged time in one direction

| Press the STOP button (3) to open the display cover (23). Restart the mowing operative in the control panel (2):

– Move the robot lawn mower to a level area and restart it.

– If the robot lawn mower has tilted because of a steep slope in the mowing area, add just the perimeter wire (18) accordingly to avoid severe inclines.

Wheel slip| – The rear wheels (8) have lifted due to an obstacle

– The rear wheels (8) can rotate freely due to an uneven lawn

| Press the STOP button (3) to open the display cover (23). Restart the mowing operation via the control panel (2):

– Move the robot lawn mower to a level area and restart

STOP button error| The display cover (23) is open but the STOP button (3) was not pressed| Press the STOP button (3) to open the display cover (23). Restart the mowing operation via the control panel (2):

– Check whether the display cover (23) displays be opened and closed freely with the STOP button (3).

– Check whether the STOP button (3) functions correctly.

Fault	Possible cause	Remedy
PCB overtime.	The temperature of the rechargeable battery is too high/low or

the controller is overheated

– If the battery temperature exceeds 65°C, the robot lawn mower will return to the charging station (19).

– If the battery temperature exceeds 45°C or drops below 0°C, charging will be stopped and the robot lawn mower will wait at the charging station (19).

| – Set the work time in summer to the early hours of the morning and avoid running the robot lawn mower during the hours of the day when it is hot.

– After the rechargeable battery or controller has cooled down to the permissible temperature range, the robot lawn mower will automatically return to the programmed operating mode

Rain| – The rain sensor (5) has.| – Wait until the robot lawn mower has dried out.

– A detailed description of the sensor can be found in section 5.2.

Sensor fault| – The robot lawn mower was stopped due to a sensor error| Switch the main switch (7) (OFF) and then switch it back on (ON) again to restart the robot lawn mower.
Motor fault/motor overcurrent| – The robot lawn mower has come to a stop because of an overcurrent in the motor or because of a motor fault| Switch the main switch (7) (OFF) and then switch it back on again (ON) to restart the robot lawn mower.

– Check the height of the grass in the mowing area and, if necessary, mow the grass to below 60 mm using a conventional lawn mower.

– Increase the cutting height. Always start with a higher cutting height and reduce it in small steps until you reach the desired height.

– Inspect the blade plates (11) and wheels for dirt and give these parts a thorough clean.

– Check the rear wheels and the blade plate

(11) for blockages. If you are unable to remove the blockages, contact the res- possible customer service center.

Breakdown| – The robot lawn mower was stopped due to an operating error| Switch the main switch (7) (OFF) and then switch it back on again (ON) to restart the robot lawn mower.

Troubleshooting

Fault	Possible cause	Remedy

The robot lawn mower comes to a stop in the mowing area. The robot lawn mower cannot be switched on:| – Battery voltage too low

– Fault in the power circuit or the electronic components

| – Bring the robot lawn mower back to the charging station (19) for charging.

– Switch on the main switch (7) (ON).

– Contact your customer service center.

The robot lawn mower cannot move into the charging station.| – The charging station (19) is not installed correctly.| – Make sure that the LED indicator (21) on the charging station (19) is lit up green.

– Make sure that the perimeter wires (18) are connected at the charging station (19) and that the front perimeter wire (18) is laid in the middle underneath the charging station (19).

– Make sure that the charging station (19) is positioned correctly.

The robot lawn mower stops or travels out of control when the near perimeter islands.| – The perimeter wire (18) has not been installed correctly around the perimeter islands.| – Adjust the position of the perimeter wire (18).

– Make sure that the perimeter wire (18) does not cross over itself

The robot lawn mower is very loud.| – Damaged blades (10)

– A large amount of foreign bodies adhere to the blades (10)

– The robot lawn mower has started too close to obstacles

– Damaged blade drive or drive motor

– Other parts of the robot lawn mower are damaged

| – Replace the blades (10). The 3 blades

(10) must all be replaced together at the same time.

– The operating eﬃciency of the robot lawn mower is dependent on the sharpness of the blades (10). You should therefore ensure that the blades (10) are maintained in good condition.

– Switch oﬀ the robot lawn mower safely and wear work gloves while you clean the blades (10) to avoid getting cut.

– Arrange for the motor to be repaired or replaced by your customer service center.

The robot lawn mower stays in the charging station. The robot lawn mower keeps returning to the charging station| – Incorrect work time settings

– The rechargeable battery is empty

– The rain sensor has been triggered

– The battery temperature is high

| – Check the work time settings.

– The robot lawn mower will begin and end its work per the set time window. Outside this time window, the robot lawn mower stays in the charging station (19).

Fault	Possible cause	Remedy

The robot lawn mower comes to a halt on the perimeter wire and is unable to get back to the charging station.| – The battery is empty

– The length of the perimeter wire (18) and therefore the distance to the charging station (19) is too great for the battery being used.

| – Remove all possible obstacles from the perimeter wire (18). When you lay out the perimeter wire (18), be sure to keep it far enough away from any obstacles.

– Please use a battery with a higher capacity.

– Important: When using a Multi-Ah battery (e.g. 4-6 Ah), set the higher capacity.

Thanks to the gentle charging and discharging of the robot lawn mower there is no need to use the lower capacity to extend the working life.

IMPORTANT! Severed perimeter wires and consequential damages are not covered by the warranty!

Charger indicator

Indicator status	Explanations and actions
Red LED	Green LED
Oﬀ	Flashing

The charger is connected to the mains and is ready for use; there is no battery pack in the charger

On| Oﬀ| Charging

The charger is charging the battery pack in quick charge mode. The charging times are shown directly on the charger.

Important! The actual charging times may vary slightly from the stated

charging times depending on the existing battery charge.

Oﬀ| On| The battery is charged and ready for use. (READY TO GO)

The unit then changes over to gentle charging mode until the battery is fully charged.

To do this, leave the rechargeable battery on the charger for approx. 15 minutes longer.

Action:

Take the battery pack out of the charger. Disconnect the charger from the main supply.

Flashing| Oﬀ| Adapted charging

The charger is in gentle charging mode.

For safety reasons, the charging is performed less quickly and takes more time. The reasons can be:

– The rechargeable battery has not been used for a very long time.

– The battery temperature is outside the ideal range.

Action:

Wait for the charging to be completed; you can continue to charge the battery pack.

Flashing| Flashing| Fault

Charging is no longer possible. The battery pack is defective.

Action:

Never charge a defective battery pack. Take the battery pack out of the charger.

On| On| Temperature fault

The battery pack is too hot (e.g. due to direct sunshine) or too cold (below 0° C).

Action:

Remove the battery pack and keep it at room temperature (approx. 20° C) for one day .

Service Information

We have competent service partners in all countries named on the guarantee certiﬁ cate whose contact details can also be found on the guarantee certiﬁ cate.
These partners will help you with all service requests such as repairs, spare and wearing part orders, or the purchase of consumables.
Please note that the following parts of this product are subject to normal or natural wear and that the following parts are therefore also required for use as consumables.

Category	Example
Wear parts*	Battery
Consumables*	Blades
Missing parts

Not necessarily included in the scope of delivery!
In the eﬀ ect of defects or faults, please register the problem on the internet at www.Einhell-Service.com.
Please ensure that you provide a precise description of the problem and answer the following questions in all cases:
Did the equipment work at all or was it defective from the beginning?
Did you notice anything (symptom or defect) before the failure?
What malfunction does the equipment have in your opinion (main symptom)? Describe this malfunction.

Warranty certiﬁcate

Dear Customer,

All of our products undergo strict quality checks to ensure that they reach you in perfect condition. In the unlikely event that this equipment develops a fault, please contact our service department at the address shown on this guarantee card.
You can also contact us by telephone using the service number shown. Please note the following terms under which guarantee claims can be made:

These guarantee terms apply solely to consumers, i.e. natural persons, who do not want to use this product in connection with either their commercial or other self-employed activities. These guarantee terms regulate additional guarantee services that the undermentioned manufacturer promises to buyers of its new products in addition to their statutory rights of guarantee. Your statutory rights of the guarantee are not aﬀected by this guarantee. Our guarantee is free of charge to you.
The guarantee services cover only defects due to material or manufacturing faults on the new product that you have bought in the European Union from the undermentioned manufacturer and are limited to either the rectiﬁ cation of said defects or the replacement of the product, whichever we prefer. Please note that only equipment under the brand name “Professional” has been designed for use in commercial, trade, or professional applications. For all other products, the guarantee is invalidated if the equipment is used within the guarantee period in commercial, trade, or industrial applications or for other equivalent activities.
Our guarantee does not cover:
- Damage to the equipment caused by failure to comply with the installation/assembly instructions or by unprofessional installation; damage caused by failure to comply with the operating instructions (e.g. connection to the wrong mains voltage or current type); damage caused by failure to comply with the maintenance and safety regulations; damage caused by exposing the equipment to abnormal environmental conditions; damage resulting from poor care and maintenance.
- Damage to the equipment caused by misuse or incorrect applications (e.g. overloading the equipment or using non-approved attachments or accessories); damage caused by foreign bodies (e.g. sand, stones, dust, ….) getting inside the equipment.
- Damage in transit; damage caused by force or external influences (e.g. by dropping the equipment).
- Damage to the equipment or parts of the equipment which is owed to use-related, normal, or otherwise natural wear.
- For example, batteries and battery packs are manufactured with a cycle limit for design-related reasons.
- Wear is negatively influenced in particular by load demands and charging speeds as well as exposure to heat, cold, vibration, and impact.
The guarantee is valid for 2 years starting from the purchase date of the equipment. Guarantee claims must be submitted before the end of the guarantee period and within two weeks of the defect being noticed. No guarantee claims will be accepted after the end of the guarantee period. The original guarantee period remains applicable to the equipment even if repairs are carried out or parts are replaced. In such cases, the work performed or parts ﬁ tted will not result in an extension of the guarantee period, and no new guarantee will become active for the work performed or for any replacement parts ﬁ tted. This also applies if on-site service is used.
To assert your guarantee claim, register the defective equipment at: www.Einhell-Service.com. You will need to provide proof of purchase of the new item of equipment. Equipment returned without such proof or a rating plate is excluded from the guarantee services because of the lack of traceability. If the defect is covered by our guarantee, then either the item in question will be repaired immediately and returned to you or we will send you a new replacement.
If you have taken the equipment with you to a diﬀerent EU country than where you bought it, we will arran-ge for a local service partner to provide the guarantee services. If you take the equipment outside the EU, the guarantee will not apply. Of course, we are also happy to offer a chargeable repair service for any defects that are not covered or are no longer covered by the scope of this guarantee. To take advantage of this service, please send the equipment to our service address. We draw attention to the restrictions of this guarantee concerning worn parts, consumables, and missing parts as presented in the service information included in this operating manual.

Warrantor/ Service:

Einhell UK Ltd, Unit 10, 1st Floor, Champion‘s Business Park, Arrowe Brook Road, Upton, Wirral, CH49 0UQ
Declaration of conformity: We declare conformity per the EU directive and standards for article

Declaration of conformity

We, Einhell UK Ltd

Champions Business Park, First Floor Unit 10, Arrowe Brook Rd, Upton, Wirral CH49 0AB, United Kingdom declare the conformity to UK standards and legislation was assessed for: Einhell-FREELEXO-LCD-BT+-3413984-Robot-Lawn-
Mower-FIG-33