SPORTOP CB800i Spinning Bike Instruction Manual

SPINNING BIKE

MODEL:CB800i
Owner’s Operating Manual

PART LIST

REAR STABILIZER (C) ASSEMBLY

STEP 1. Lift up the rear side of main frame (A), and using one styrofoam to hold it.
STEP 2. Equip the rear stabilizer (C) with the main frame (A) by using the screws (1), washers (2), and nuts (3) to tighten it.
STEP 3. Take away the Styrofoam.

FRONT STABILIZER (B) ASSEMBLY

STEP 1. As the same as figure 1, lift up the front side of main frame (A), and using one styrofoam to hold it.
STEP 2. Equip the front stabilizer (B) with the main frame (A) by using the screws (1), washers (2), and nuts (3) to tighten it.
STEP 3. Take away the styrofoam.
STEP 4. Adjust the levelers on the bottom of rear and front stabilizers to stabilize the machine.

HANDLEBAR (F) & BOTTLE HOLDER (G1) ASSEMBLY

HANDLEBAR
STEP 1. Remove the preassembled screw (J4) from the handlebar tube (E).
STEP 2. Release the knob (J) then insert the handlebar (F) to the handlebar tube (E). Fix the screw (4) back to the handlebar tube (E). Tighten the knob () to lock the handlebar (G1).

LEFT & RIGHT PEDAL (K1 & K2) ASSEMBLY

STEP 1. Equip the left pedal (K1) with the crank (L) by anticlockwise direction.
STEP 2. Equip the right pedal (K2) with the crank (R) by clockwise direction..

ADJUSTMENT FOR SADDLE & HANDLEBAR

STEP 1. There are four fix knobs () as the picture shown.
STEP 2. Turn one of the knobs () at one time and adjust the post to the proper position for user.
STEP 3. Then turn back all the knobs () to fix the fitting.
WARNING: FOR YOUR SAFETY, never turn any knob (J) while the machine is in motion, only when it is at a full  complete stop then it is safe to turn the knob.

Congratulations!
You have completed assembly of your spinning bike.

HOW TO ASSEMBLE MOBILE HOLDER

Step 1. Assemble the mobile holder base

A. Insert stationary base (L2) with mobile holder (L 1) from bottom as figure shown.| B. Assemble fixing band (L3) as figure indicated.| C. Complete the mobile holder assembly
---|---|---

Step 2. Place mobile holder base (L1+L2) on handlebar (F) then tighten fixing band (L) to hook on stationary base (L2) for fixation.

POWER SUPPLY OPTION FOR BLUETOOTH DEVICE

A-Position Machine on consideration for convenience, using the adaptor(N), there is one adaptor hole located at the rear of the machine.

B-Open the battery housing cover then insert battery’s, fix the battery’s by the cover.

HOW TO MAKE DIFFERENT TENSION ADJUSTMENT?
HOW TO STOP THE SPINNING BIKE (FL YING WHEEL)?
Knob (A1) provides the tension micro adjustment.
Turn clockwise direction to increase the tension.
And turn anticlockwise direction to decrease the tension.
If there is any necessary to stop the machine when pedaling, just press down the knob (A1).

HOW TO MOVE THE MACHINE?

Hold the handlebar and push down the handlebar until the front transportation wheels are touching the ground. You may now move the machine to the desired location.
After the move, gently set the machine down at its new location and adjust the levelers on the bottom of stabilizers to stabilize the machine if needed.

[INSTRUCTION MANUAL OF I Biking]

iBiking+ support following devices:
iPod touch (4th generation)/iPod touch (3rd generation)
iPhone 4S / iPhone 4 / iPhone 3GS
Android phone OS 4.0 or above
Andriod phone resolution 1280×800 pixels, 1280×760 pixels, 800x480pixels “Made for iPod,” “Made for iPhone,” and “Made for iPad” mean that an electronic accessory has been designed to connect specifically to iPod, iPhone, or iPad, respectively, and has been certified by the developer to meet Apple performance standards. Apple is not responsible for the operation of this device or its compliance with safety and regulatory standards. Please note that the use of this  accessory with iPod, iPhone, or iPad may affect wireless performance.
iPad, iPhone, iPod, iPod classic, iPod Nano, iPod shuffle, and iPod touch are trademarks of Apple Inc., registered in the U.S. and other countries.

iBiking+ APP download

1. APP name: ” I Running+” on Google play/ iTunes store
2. QR code:

https://play.google.com/store/apps/details?id=com.appdevice.spinningbike&feature=more_from_developer#?t=W251bGwsMSwxLDEw
https://play.google.com/store/apps/details?id=com.appdevice.spinningbike&feature=more_from_developer#?t=W251bGwsMSwxLDEw

Bluetooth Pairing

1. Turn on Bluetooth on personal mobile device, search for console device “iBiking+” and press connect.
2. Turn on iBiking+ app on mobile device, and press connect to start workout with personal mobile device. (password: 0000)

iBiking+ App Operation

Finish workout ­

Sync with Runkeeper or MMF; share with Facebook or Twitter

i-Center ­

NOTE:

1. Turn off iBiking+ Bluetooth sensor when stop workout.
2. If battery power is too low to operate Bluetooth sensor, the red LED power indicator will illumniate, please change battery or use the adaptor as power snpply.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>