Magene T300 22 Smart Trainer User Manual

October 30, 2023
Magene

Magene logo

T200

Magene T300 22 Smart Trainer

RIDE ON

POWER UP
REACH BEYOND

[P8]          ATTACHING YOUR BICYCLE (THRU AXLE)

Magene T300 22 Smart Trainer a1

[P9]                                           CONNECTING TRAINER

Magene T300 22 Smart Trainer a2

[P10]                                     MODES AND INDICATORS

Magene T300 22 Smart Trainer a3

QUICK START GUIDE AND INSTRUCTIONS

Thank you for purchasing the T200 Smart Trainer.
Please read the instructions carefully before using it.

If you have any questions, please contact us immediately:

UNPACKING P1

After you take out the trainer and accessories from the package, please make sure to keep the original product packaging for future transportation or storage. When encountering after-sales problems, please be sure to use the original packaging for mailing; the manufacturer will not be responsible for any damage caused by mailing in non-original packaging. If the original packaging is lost, please contact your local distributor or after-sales service personnel.

(1) T200 Smart Trainer
(2) AC Power Adapter
(3) Hex Tool
(4) Quick Release Skewer
(5) Freehub Body Spacer
(6) Adapter A – Quick Release End Cap (installed already)
(7) Adapter B – For 130mm and 135mm Quick Release
(8) Adapter C – Thru-axle cap
(9) Adapter D -12142/12148 Thru-axle open gear converter

Caution:

  1. The following diagrams of tools and accessories are printed only to illustrate the use of the product, and the configuration of the real product parts is subject to the packing list.
  2. Thru Axle bicycle frame must use Thru Axle conversion kit.
INSTALL THE TRAINER P2
  1. Remove the main trainer unit from the box, and expand the trainer.
  2. Take out the legs and insert them into the bolts (note that the square hole of the arm is at the bottom and the round hole is at the top).
  3. Install the legs on the trainer, with white leg on the white arm, and then tighten the nuts and install the protective caps.
  4. When installing, pay attention to the left and right direction of the legs, the long side should be placed near the drive side.
INSTALLING CASSETTE P3

Before installation, please prepare cassette, wrench and sleeve.

  1. To install a compatible 9, 8 or 10 speed cassette, it will be necessary to use the included 1.85mm spacer, but not so for 11 or 12 speed cassette.
  2. Put the cassette onto the freehub in order from big to small size accordingly, paying attention to the alignment of the freehub spline.
  3. Install the cassette cover and tighten it roughly by hand.
  4. Wrap the card fly chain whip around the flywheel, then insert it into the flywheel dedicated sleeve, and tighten the flywheel with an adjustable wrench.
INSTALLING QUICK RELEASE P4
  1. The quick release end cap on the freehub has been installed by the manufacturer.
  2. Choose the quick release matching the specification of your bicycle, and insert the quick release adapter into the non-drive side of the trainer.
  3. Insert the quick release skewer into the non-drive side of the trainer; insert the conical springs into the left and right ends of the quick release skewer separately, with the tips facing inward, and then screw on the nuts.
INSTALLING THRU AXLE ADAPTER P5
  1. Use a 5mm hex to unscrew the quick release end cap on the freehub body counterclockwise.
  2. Use a wrench to tighten the thru axle end cap.
  3. Choose the thru axle matching the specification of your bicycle, and insert the thru axle adapter into the non-drive side of the trainer.
INSTALLING XDR FREEHUB BODY P6

SRAM XDR freehub, thru axle end caps need to be purchased separately.

  1. Use a 5mm hexagon socket to counterclockwise unscrew the quick release end cap on the freehub body
  2. Pull out the original freehub.
  3. Insert your XDR freehub into the trainer, turn it counterclockwise and keep pressing the freehub and detent of the freehub until the freehub is fully installed in place.
  4. Screw on the end cap of the thru axle and use a wrench to lock it in place.
  5. Choose the thru axle matching the specification of your bicycle, and insert the adapter of the thru axle into the non-drive side of the trainer.
ATTACHING YOUR BICYCLE (QUICK RELEASE) P7
  1. Shift your bicycle chain into the smallest sprocket in the front and rear.
  2. Release the rear brake, open the quick release skewer, lift the bicycle frame, and then remove your rear wheel.
  3. Push the quick release skewer on the trainer to the “open” mode, seat the bike on the trainer, and then align the chain with the smallest sprocket on the trainer.
  4. Lift the front wheel up while pressing down on the saddle to ensure the bicycle is fully seated on the trainer.
  5. Tighten the quick release nuts while turning the quick release skewer on and off frequently until resistance is felt.
  6. Lock the thru axle and wiggle the bicycle frame to ensure that the frame does not fell off from the trainer.
ATTACHING YOUR BICYCLE (THRU AXLE) P8
  1. Shift your bicycle chain into the smallest sprocket.
  2. Release the rear brake, remove the thru axle, lift the bicycle frame, and then remove your rear wheel.
  3. Align the rear axle with the trainer’s axle hole in the center, insert the barrel axle, and then aligning the chain with the smallest sprocket.
  4. Lock the thru axle and wiggle the bicycle frame to ensure that the frame does not fell off from the trainer.

CAUTION!

  • Failure to properly tighten the quick release skewer or thru axle may result in property damage or personal injury.
  • If you are unsure of proper assembly, please consult your local bike shop or contact us for assistance.
  • Failure to properly assemble the quick release skewer or thru axle, please do not ride the trainer.
  • Do NOT ride the trainer until the quick release skewer or thru axle is tightened, thus avoiding damages.
  • Do NOT adjust the quick release skewer or thru axle while someone is sitting or standing on the bike.
ACTIVATING AND PERFORMING A SPIN DOWN

CAUTION! The new product must be activated before first use.

  1. Turn on Bluetooth of your cell phone.
  2. Download Magene Utility App and connect to the trainer.
  3. Select your device to connect and activate.

CAUTION! A spin down should performed for the new product before first use.

  1. Download Magene Utility App and connect to the trainer.
  2. Ride with 150W power for 10 minutes to achieve the best efficiency of the drive chain.
  3. Follow the prompts for a spin down.
  4. The spin down should be repeated once every two weeks to ensure accurate power measurement.
CONNECTING TRAINER P9

CAUTION! The hardware and software you use must support ANT+ or BLE 4.0 and above. For PC without built-in Bluetooth, you can install a Bluetooth receiver or ANT+ Dongle (sold separately).

  1. Power on the trainer and the indicator light on the housing will illuminate.
  2. Download Onelap App and register your account.
  3. Select the sports mode as “bike”.
  4. Select the corresponding trainer in the device list to connect.
  5. Select your workout program and start riding.
MODES AND INDICATORS P10

The trainer has two indicators.

Led Indicator Description

System status indicator (1)

|

Connection indicator (2)

---|---
Power-on status: the red and blue indicator flash twice alternatively| Not connected: the blue indicator flashes
Standby status: the blue indicator flashes| Connected: the blue indicator is on
Riding status: the blue indicator is on

PRODUCT SPECIFICATION

Model ____ P0102005
Rated voltage/Current __ DC 12V, 4A
Maximum simulated slope 15%
Max power __ 1800W
Power accuracy __
±2.5%
Rotational inertia 2.62kg*m²
Noise level ____
<56dB @1.5m&30km/h
Wireless protocol ____ Bluetooth & ANT+™ FE-C
Size (unfolded)
480750500mm
Size (folded) _ 480230500mm
Overall weight ___
13.6kg
Compatible cassette ____ Shimano, SRAM 8-11 speed cassette Shimano 12-speed cassette SRAM XDR 12-speed cassette
Compatible bicycle frame __ 130/135mm Quick Release 12142/12148mm Thru Axle
Compatible wheels _____ 26″~29″MTB 700C RD

Magene T300 - Labels

www.magene.com
support©magene.com
T/CHINABICYCLE 13
V2.0

FCC Statement:
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radiator television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help.
Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

This equipment should be installed and operated with minimum distance 20cm between the radiator & your body.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals