EPSON EB-810E, EB-815E Projector User Guide

: June 12, 2024
: Epson

EPSON EB-810E, EB-815E Projector

Product Information

The EB-810E/EB-815E is a projector that offers high-quality image projection for various applications. It supports multiple connection options, including HDMI, USB, Ethernet, and HDBaseT. The projector also features a PC Free feature, allowing users to connect digital cameras, USB flash drives, USB storage devices, and Epson document cameras directly to the projector.

Product Usage Instructions

Before using the projector, please read the safety instructions in the online User’s Guide.

Connect the Projector

Remove the side cover of the projector.
Choose one of the following connection options:
- HDMI cable: Connect a computer or video device using an HDMI cable.
- USB cable: Connect a computer or video device using a USB cable.
- HDBaseT transmitter: Connect the projector to an optional HDBaseT transmitter using a 100Base-TX network cable. Use a Cat5e (Category 5e) STP cable or better.
- Wired network: Connect the projector to your network using an Ethernet cable.
- Streaming device HDMI cable: Connect a streaming device to an HDMI port on the projector. You can also connect it to the projector’s USB-A (flat) port for power.
- Camera, USB device, or document camera: Connect a digital camera, USB flash drive, USB storage device, or Epson DC-07 document camera to the projector’s USB-A (flat) port using a USB cable.

Using the Remote Control:

Install two AA batteries into the remote control.
To turn the projector on or off, press the power button on the projector or remote control. To shut down the projector, press the power button twice.
To select the image source, press the Source Search button on the remote control.
To adjust the image position and height, move or rotate the projector accordingly.
To access the projector menus, press the Menu button on the remote control. Use the navigation buttons to navigate through the menus.
To adjust the image sharpness, move the focus lever up or down.
To control the projector volume, use the volume buttons on the remote control.
To access the Home screen, press the Home button on the remote control.

For more detailed information and troubleshooting tips, please refer to the online User’s Guide.

Quick Setup

IMPORTANT: Before using the projector, make sure you read these instructions and the safety instructions in the online User’s Guide.
Note: Product availability varies by country and region.
Note: The illustrations show the EB-810E, but the steps are the same for all models, unless otherwise specified.

Connect the projector

Remove the side cover.

Computer
Choose from the following connections. See the sections below or the online User’s Guide for details.

EPSON-EB-810E,-EB-815E-Projector-fig-3

HDMI® port
Connect one end of an HDMI cable to one of the projector’s HDMI ports and the other end to an HDMI port on your computer.

USB port

Connect the square end of a USB cable to the projector’s USB-B (square) port. Connect the flat end of the cable to any USB port on your computer.
Windows® 7 or later: After turning on the projector, follow the on-screen instructions to install the Epson® USB Display software (EMP_UDSE.EXE; only on first connection). If the software screen does not display automatically, open My Computer, Computer, or This PC, then double-click EPSON_PJ_UD.
OS X 10.8.x or higher: After turning on the projector, the setup folder for USB Display appears in the Finder. Double-click USB Display Installer and follow the on-screen instructions to install the Epson USB Display software (only on first connection). If the software screen does not display automatically, double-click EPSON_PJ_UD, then double-click USB Display Installer.

HDBaseT®
Connect the projector to an optional HDBaseT transmitter using a 100Base-TX network cable. Use a Cat5e (Category 5e) STP cable or better.

EPSON-EB-810E,-EB-815E-Projector-fig-4

Wired network
Connect the projector to your network using an Ethernet cable. See “Wired network configuration” for more information.

EPSON-EB-810E,-EB-815E-Projector-fig-5

Video device
Connect multiple video devices and use the Source Search button on the projector or remote control to switch between them. For more information on playing sound through the projector, see the online User’s Guide.

EPSON-EB-810E,-EB-815E-Projector-fig-6 Note: If you connected a streaming device to an HDMI port, you can also connect it to the projector’s USB-A (flat) port for power.

Camera, USB device, or document camera

Connect a digital camera, USB flash drive, USB storage device, or Epson DC-07 document camera to the projector’s USB-A (flat) port.
If you connect a digital camera, USB flash drive, or USB storage device, you can use the projector’s PC Free feature. You can also connect other Epson document cameras to the projector. See the online User’s Guide for details.

Using the remote control

Install the two AA batteries as shown.

EPSON-EB-810E,-EB-815E-Projector-fig-8

For more information on using the remote control, see the online User’s Guide.

Turn on your equipment

Remove the side cover, if necessary.
Turn on your computer or video source.
Make sure the power cord is connected and plugged into an electrical outlet.
Press the power button on the projector or remote control. Theprojector beeps, and the status light flashes blue and then stays on.
Note: To shut down the projector, press the power button twice.
If you don’t see an image, press the Source Search button on theremote control to select the image source.
Note: If you still see a blank screen or have other display problems, see the troubleshooting tips on the back of this sheet.
The default language of the menu system is English. To select anotherlanguage, press the Menu button on the remote control. Select Management and press . Select Language and press . Select your language and press . Press the Menu button to exit the menu system.

Adjust the image

To adjust the image position, move the projector while keeping it level and parallel to the screen. To adjust the image height, rotate the rear foot to extend or retract it.
To adjust a tilted image when the projector is set on a flat surface, adjust the front feet so both sides are level.
Remove the side cover, if necessary.
Move the focus lever up or down to adjust the image sharpness.
5 Replace the side cover.
Note: For more detailed adjustment methods, see the online User’s Guide.

Network your projector

Wireless network configuration
Follow these steps to set up the projector for a wireless network connection.

Press the Menu button on the remote control.
Select the Management menu and press .
Select On as the Wireless LAN Power setting.
Select the Network menu and press .
Select Network Settings and press .
Note: If you are prompted to enter a password for Epson Web Remote and for Epson Web Control, you can create a password or leave it blank.
Select Wireless LAN as the Priority Control Interface setting.
Select one of the following as the Simple AP setting:•
On for a direct connection to a computer, tablet, or smartphone. Youwill need to create a passphrase.
Off to connect your projector to a router or access point.
Note: If you connect to the projector directly, you can only project locally stored content.
Select any other wireless settings as necessary. See the online User’s Guidefor details.
When you are finished, return to the Network Settings menu and selectSet to apply your settings. Then select Yes to save the settings.
Press the Menu button to exit the menu system.

Wired network configuration
Follow these steps to set up your projector for a wired network connection.

Press the Menu button on the remote control, select the Network menu,then press .
Choose Network Settings and press .
Note: If you are prompted to enter a password for Epson Web Remote and for Epson Web Control, you can create a password or leave it blank.
Select Wired LAN as the Priority Control Interface setting.
Select the Wired LAN menu and press .
Choose IP Settings and press .
If your network assigns addresses automatically, make sure the DHCP setting is on. If not, make sure DHCP is off and enter the projector’s IP Address, Subnet Mask, and Gateway Address, as needed. Then press Esc.
To prevent the IP address from appearing on the network standby screen, set the IP Address Display setting to Off.
When you are finished, return to the Network Settings menu and select Set to apply your settings. Then select Yes to save the settings.
Press the Menu button to exit the menu system.

Install the optional software

You can use Epson iProjection™ software to display wirelessly from a computer to your networked projector. Download the software and operation guide from your product’s support page (see “Where to get help”) and install the program on each computer that will project over the network.
To monitor and control your projector over the network, download and install the Epson Projector Management software (Windows only) and operation guide from your product’s support page (see “Where to get help”).

Project over a network

If you need to configure the projector for a wired network, see “Wired network configuration.”

Press the LAN button on the remote control. You see a screen like this:
Start Epson iProjection on your computer.
- Windows 11: Select > All Apps > EPSON Projector > Epson iProjection Ver.X.XX.
- Windows 10: Select > EPSON Projector > Epson iProjection Ver.X.XX.
- Windows 8.x: Navigate to the Apps screen and select Epson iProjection Ver. X.XX.
- Windows 7: Select or Start > Programs or All Programs > EPSON Projector > Epson iProjection > Epson iProjection Ver X.XX.
- macOS 10.13.x or higher: Double-click the Epson iProjection icon in the Applications folder.
Select Advanced Connection Mode and click OK.
Select the projector you want to connect to, then click Join.
If you don’t see the projector you want, click the Automatic search button to find the projector automatically, click the Manual search button to enter the projector’s IP address, or click the Profile button to find the projector based on a previously saved profile.
If you see a message asking for a keyword, enter the four digits that appear on the LAN standby screen and click OK.
Your computer image is projected, with a floating toolbar:
When you’re done presenting, click Leave on the toolbar.

Using the Epson iProjection app

You can project wirelessly from a mobile device (iOS, Android™, or Chromebook™) using the Epson iProjection app and a QR code.

Scan the following QR code to download and install the Epson iProjection app.
If you connected the projector to a network wirelessly, make sure to connect your mobile device to the same network.
Press the LAN button on the remote control to display a QR code on the projector screen.
Start Epson iProjection on your mobile device.
Use the QR code reader feature to read the QR code displayed.
Follow the app instructions to connect your device to the projector.
For more information on setting up and using this app, visit http://epson.com/projectorapp (U.S.), http://epson.ca/projectorapp (Canada), or http://latin.epson.com/iprojection (Latin America).

Using web remote

You can use a standard web browser to control the projector through the network. A virtual remote control on your computer screen lets you perform many of the same functions as you can with the physical remote control.

Open your web browser and enter the IP address of the projector you want to monitor in the browser’s address bar. The Epson Web Control menu opens.
If you’re not sure what the IP address of the projector is, turn the projector on and select Wired LAN Info or Wireless LAN Info from the Network menu to display the IP address of the projector. (Do not enter the leading zeroes.)
Select Basic Control or Remote. If you see a login screen, enter EPSONWEB as the user name. If a password was created, enter the password.
Use the on-screen buttons to operate the projector, as you would using the remote control. See the online User’s Guide for details.

Managing content

You can manage content from your computer using the Epson Projector Content Manager software, or over the network using a web browser (Epson Web Control) or the Epson iProjection app.

Using the Content Manager software
The Epson Projector Content Manager software allows you to add images and movies to playlists and load them easily and directly to your projector via USB for playback.
Note: Download and install the Epson Projector Content Manager software from your product’s support page (see “Where to get help”). For more information, see the online Epson Projector Content Manager Operation Guide or the online User’s Guide.

Troubleshooting

If you see a blank screen, check the following:
- Make sure your computer or video device is properly connected.
- Make sure the status light on the projector is blue and not flashing.
- Press the power button or the A/V Mute button on the remote control to wake the projector from standby or sleep mode, if necessary.
If you see a blank screen when a computer is connected, check the following:
- On Windows, hold down the Windows key and press P at the same time, then click Duplicate.
- If you are using a Mac laptop with macOS 13, select System Settings > Displays. Press the + pop-up menu button, then choose a display to mirror.
- On macOS 12, select System Preferences > Displays > Display Settings. Select the projector, then choose the mirror option for your display from the drop-down menu.
- On macOS 11 and older, open System Preferences and select Displays. Click the Arrangement tab and select the Mirror Displays checkbox.
If the projector does not respond to remote control commands, make sure the batteries in the remote control are installed correctly. Replace the batteries, if necessary.

Registration

Register today to get product updates and exclusive offers. You can register online at http://epson.com/webreg.

Where to get help

Manuals
For more information about using the projector, you can view or download the manuals from the Epson website, as described below.

Internet support
Visit http://epson.com/support (U.S.), http://epson.ca/support (Canada), or http://latin.epson.com (Latin America) and search for your product to download software and utilities, view manuals, get FAQs and troubleshooting advice, or contact Epson.

Telephone support

To use the Epson PrivateLine® Support service, call 800-637-7661 (U.S. and Canada). This service is available for the duration of your warranty period. You may also speak with a support specialist by calling 562-276-4394 (U.S.) or 905-709-3839 (Canada).
Support hours are 7 a.m. to 4 p.m., Pacific Time, Monday through Friday. Days and hours of support are subject to change without notice. Toll or long-distance charges may apply.
In Latin America, see the online User’s Guide for technical support information.

Optional accessories

For a list of optional accessories, see the online User’s Guide.
You can purchase screens or other accessories from an Epson authorized reseller. To find the nearest reseller in the U.S. or Canada, call 800-GO-EPSON (800-463-7766). Or you can purchase online at http://epsonstore.com (U.S. sales) or http://epsonstore.ca (Canadian sales).
To find the nearest reseller in Latin America, go to http://latin.epson.com.

ABOUT COMPANY

EPSON is a registered trademark, the EPSON logo is a registered logomark, and Epson iProjection is a trademark of Seiko Epson Corporation.
PrivateLine is a registered trademark of Epson America, Inc.
Mac, macOS, and OS X are trademarks of Apple Inc., registered in the U.S. and other countries.
Android and Chromebook are trademarks of Google LLC.
Microsoft and Windows are trademarks of the Microsoft group of companies.
General Notice: Other product names used herein are for identification purposes only and may be trademarks of their respective owners. Epson disclaims any and all rights in those marks.
This information is subject to change without notice.