Magene HRM30 Heart Rate Monitor User Manual
- June 5, 2024
- Magene
Table of Contents
Heart Rate Monitor
Model: HRM30
Safety Warnings and Product Information
Warning
Failure to notice the potential dangers listed below may lead to severe harm
or even fatal accidents.
Battery-related warning
The product uses a CR2032 button cell battery. Failure to follow the
instructions listed below may shorten the battery’s shelf life, damage the
device, cause fire, chemical burns, battery leakage, or the risk of injury. Do
not disassemble, modify, puncture, or damage the device or the battery.
- Do not expose the device or the battery to fire, explosion, or other hazards.
- Do not place or store the device near a dryer, in a car under direct sunlight, or in other high-temperature environments.
- Do not immerse the battery in water or other liquids.
- Do not use any sharp object when removing the button cell battery.
- Keep the battery out of reach of children. Swallowing the battery may cause chemical burns, soft tissue perforation, or even death. Seek immediate medical help if the battery is swallowed.
Health-related warnings
- If you are implanted with electronic devices in your body, such as a pacemaker, consult your physician before using the heart rate sensor.
- Data on the heart rate sensor is for reference only and cannot be used for the medical diagnosis, monitoring, treatment, or prevention of any disease. Magee is not responsible for the consequences of any data error.
Our Product
The heart rate sensor monitors your heart rate during sports. It supports ANT+ and Bluetooth wireless protocols, allowing you to send heart rate data to a mobile app, bike computer, sports watch, or any other smart device that supports standard ANT+ and Bluetooth protocols. Recording each and every heartbeat, it enables scientific and pleasant training.
Wearing the Heart Rate Sensor
*To avoid errors in the collected heart rate data, make sure to place the heart rate sensor in the proper direction. Wear the heart rate monitor directly on your skin, just below your chest. It should be snug enough to stay in place during your activity
- Wet the electrode areas on the reverse side of the strap.
- Press the snap studs on the sensor into the snap sockets on the strap, respectively. Be sure to place the heart rate sensor in the proper direction.
- Wrap the strap around your chest and attach the hook to the other end of the strap.
- Move the sensor to just below your chest and let the electrodes contact your skin.
- After the sensor is properly worn, it will automatically turn on, the front LED flashes (turns off after 10 times), select the correct ANT ID or Bluetooth ID on the bike computer, watch, and APP, and the heart rate data will be transmitted.
Pairing and Settings
Pairing the heart rate sensor with an ANT+ device
Wear the heart rate sensor before you can pair it with a compatible device.
Keep the sensor within 3 meters of the device to be paired and over 10 meters
away from other ANT+ devices. When the initial pairing is complete, the
compatible device will automatically identify the enabled sensor.
Pairing the heart rate sensor with a Bluetooth device
Wear the heart rate sensor before you can pair it with a compatible device.
Keep the sensor within 3 meters of the device to be paired and over 10 meters
away from other Bluetooth devices. The sensor cannot be found by directly
using Bluetooth on a phone and can only be connected to a Bluetooth device or
an app at the same time. When the initial pairing is complete, the compatible
device will automatically identify the enabled sensor.
Battery Replacement
- Use a coin to rotate the arrow mark on the battery cover anticlockwise from the locking position to the opening position. You can then open the battery holder.
- Remove the used battery.
- Place a new battery into the battery holder. Align the arrow mark to the opening position and press down the battery cover (see figure below). After pressing the whole cover into the battery holder, use a coin to rotate the arrow mark clockwise to the locking position.
*You may have to re-pair the heart rate sensor after battery replacement.
Specifications
Heart rate range | 30-240BPM |
---|---|
Battery type | 3V CR2032 button cell |
Battery shelf life | 1000 hours |
Wireless transmission protocol | Ant+ and Bluetooth |
Operating temperature | -10°C-50°C |
Protection rating | IP67 |
Weight | 16g |
Sensor dimensions | 62.335.111.5mm |
Strap length | 64-86cm(± 2cm) |
Warranty
This product has passed strict quality inspections. Any failure caused by product quality problems under normal use will be covered by a free warranty within the warranty period.
- Within 7 days (inclusive) from the date of purchase, if there is a quality problem with the product itself, it will be returned unconditionally.
- The product warranty period is 12 months, subject to the warranty period of the warranty card.
- Product warranty repairs need to use the original factory packaging and select the designated logistics transportation, otherwise, the user will bear the freight or transportation losses.
The following situations do not belong to the scope of the warranty:
- Exceeding the validity period of the warranty.
- Any damage caused by improper use, maintenance, and storage.
- Product damage caused by use or installation is not in accordance with the instructions.
- Unauthorized maintenance, misuse, collision, negligence, abuse, liquid ingress, accident, alteration, and unclear use of non-product accessories.
- No warranty card or valid invoice.
- The product number or code on the warranty card does not match the actual product.
- Other failures and damages are not caused by the design, manufacturing, and quality of the product itself.
- Wear and dirt are caused by normal use, such as scratches, and damage caused by human factors such as contact with chemical reagents, contact with sharp objects, falling, and squeezing.
- Damage is caused by irresistible factors.
FCC Statement
This device complies with part 15 of the FCC rules. Operation is subject to
the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
NOTE: The manufacturer is not responsible for any radio or TV
interference caused by unauthorized modifications or changes to this
equipment. Such modifications or changes could void the user’s authority to
operate the equipment. For a Class A digital device or peripheral, the
instructions furnished to the user shall include the following or similar
statement, placed in a prominent location in the text of the manual:
NOTE: This equipment has been tested and found to comply with the limits
for a Class A digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference when the equipment is operated in a commercial environment. This
equipment generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the instruction manual, may cause
harmful interference to radio communications. Operation of this equipment in a
residential area is likely to cause harmful interference in which case the
user will be required to correct the interference at his own expense
Magee Heart Rate Monitor
Model| HRM30
| Nominal Voltage:3V (CR2032)
| Nominal Capacity:240mAh (CR2032)
| Ref.Weight:3.0g (CR2032)
Manufacturer| Qingdao Magene Intelligence CQ., Ltd.
Address| No.2 AWS, Road, Licang District,
| Qingdao Shandong China
| WSJ Product LTD(for authorities only)
Eschborner LandstraBe 42-50
60489 Frankfurt am Main,Hessen, Germany
For more information, contact us:
Qingdao Magene Intelligence Technology Co., Ltd.
Website: www.magenefitness.com
After-sales support:
support@magenefitness.com
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>