BRiGADE ZS-1000-ECU RFID Detection System Installation Guide

October 30, 2023
BRiGADE

1000-ECU RFID Detection System
Installation Guide

BRiGADE ZS-1000-ECU RFID Detection System

RFID Detection System

Control Unit – ZS-1000-ECU/ZS-1001-ECU(NA)
Antenna – ZS-1000-AP/ZS-1001-AP(NA)

12-24V System wiring

BRiGADE ZS-1000-ECU RFID Detection System - Fig11

Control Unit wires

BRiGADE ZS-1000-ECU RFID Detection System-

Antenna switch settings

Locate SW1 & SW2 inside antenna unit.
SW1 = Antenna Power/Detection range
To set detection range manually, select: No.1=Min to F=Max
Note: Manual settings cannot be overridden by WiFi controller.
To set detection range via Control Unit WiFi network, select: 0

Important! The system has two range levels which must be set depending on the required detection distance. See ‘Connect using Control Unit WiFi’ (overleaf) for instructions.
SW2 = Antenna Address
Set first connected antenna to No.1 Set up to 6 antennas sequentially: (Second antenna to No.2, third antenna to No.3 etc.)

Antenna mounting

Mount antenna vertically (best) or horizontally on a flat surface. For vertically mounted antennas in high positions, angle unit downwards.

Control Unit and Antenna fixing

BRiGADE ZS-1000-ECU RFID Detection System - Fig1

Turn system on

BRiGADE ZS-1000-ECU RFID Detection System - Fig2

Turn system off

BRiGADE ZS-1000-ECU RFID Detection System - Fig3

Alarms

State Alarm Light Sounder Button
1 tag detected Red (Slow Flash) Two Tone Slow Red
2+ tags detected Red (Fast Flash) Two Tone Fast Red
System Error Pink (Flash) System Beep Red
No Ignition Red (Fading Pulse) One Tone Red
No Driver Tag Red (Fading Pulse) One Tone Red
Wi-Fi Connected Blue (Fading Pulse)     X Green
System OK X X Green

Connect using Control Unit WiFi

Connect to Control Unit WiFi network:
Note: Requires both permanent and ignition
ZoneSafe_XXXXX
Substitute ‘XXXXXX’ for the serial number of your Control
Unit (found on rear of control unit).
WiFi password: ZONESAFE
Open a web browser.
Enter address: http://192.168.0.1/

Enter:
Username: admin
Password: PASSWORD
Usernames and passwords are case-sensitive.
Note: A changed password is not recoverable unless returned for factory resetting

View & change settings

BRiGADE ZS-1000-ECU RFID Detection System - Fig8

Available Tags
Pedestrian (grey) & Driver (yellow) VibraTags
Carried by personnel. VibraTags provide short bursts of vibration when detected. VibraTags are hermetically sealed and the high-capacity battery can be wirelessly charged within two hours and can last up to three months between charges. USB wireless desktop charger sold separately.

AssetTag
AssetTags fit into PVC safety cones with an internal neck diameter of between 39 and 42mm/1.5″ and 1.75″(11/2″ and 13/4″).
AssetTags are shockproof and weatherproof.
The replaceable batteries last up to three years under normal use.

Box contents

ZoneSafe Control Unit: ZS-1000-ECU
a) ZoneSafe Control Unit (x1) Part No: 5881
b) Cable Loom & Connector (x1)
c) Inline Fuse Holder (x2)
d) 7.5 Amp Blade Fuse (x2)
ZoneSafe Antenna Unit: ZS-1000-AP
e) ZoneSafe Antenna (x1) Part No: 5882
f) IP67 cable grommets (x3)
g) M4 x 35mm Hex Screw (x6)
h) 6 Way Screw Terminal (x2)
i) Collar cable grip (x2)
Note: Driver, Pedestrian or Asset Tags required to operate system (available separately)

BRiGADE ZS-1000-ECU RFID Detection System - ig3

Installation requirements

  • 12-24V DC Supply Voltage
  • 1 Amp Per Antenna
  • 0V Earth
  • 4 x M5 screws (Max thread engagement 8mm)
  • Control Unit serial number for WiFi connection
  • ALPHA Wire 6010C*
  • Mounting/Fixing Option*
  • Driver, Pedestrian or Asset Tags*
  • Available separately

For this Quick Start Guide in other languages
and Full User Manual in English only visit:
www.brigade-electronics.com
4018.10.20 © Brigade Electronics Group Plc

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals