ZEVNI A04804W4 Evin 31-in 4-Light Black/Brass Transitional Vanity Light Instruction Manual
- June 8, 2024
- ZEVNI
Table of Contents
+1 850 296 2377 Working hours : Mon – Fri 9:00 – 16:00 EST
homecustomercare@outlook.com
Item Number: A04804W4
WARNING (To reduce the risk of fire, electric shock, or personal injury):
-
We suggest installation by a licensed electrician.
-
Please read the instruction carefully and save it as you may need it at a later time.
-
Before you start, NEVER attempt any work without shutting off the electricity until the work is done.
» Go to the main fuse, or circuit breaker, box in your home. Place the main power switch in the “ OFF ” position.
» Place the wall switch in the “ OFF ” position. -
Mounting surface should be clean, dry, flat, strong enough and 1/4” larger than the canopy on all sides. Any gaps between the mounting surface and canopy exceeding 3/16” should be corrected as required.
-
Make sure that the ceiling or wall can stand the weight of the lamp before installation.
-
Make sure the voltage you are using is 120V. The maximum wattage is 40W per bulb.
-
Keep the lamp away from acidic and alkaline substances in case of damaging the surface of the lamp.
-
When replacing bulbs, you should turn off or unplug the lamp and you must wait until it is cool as bulbs get hot quickly.
-
The safety instructions appearing in this manual are not meant to cover all possible conditions that may occur. It must be understood that common sense, caution and care must be used with any electrical products.
IMAGE FOR FINISHED PRODUCT:
TOOLS REQUIRED (NOT INCLUDED):
Before starting assembly and installation please prepare the needed tools as below picture
| | | |
---|---|---|---|---
Ladder| Philips Head or Flat Blade Screwdriver| Electrical
Tape| Pilers| Wire Cutter/Stripper
ACCESSORIES ENCLOSED:
(A) Mounting screw (2)
(B) Plastic wire connector (3)
PARTS INCLUDING:
(C) Mounting plate (1)
(D) Green ground screw (1)
(E) Back plate (1)
(F) Stud (2)
(G) Screw (12)
(H) Socket (4)
(I) Glass shade (4)
ASSEMBLY & INSTALLATION INSTRUCTIONS:
1. Carefully remove the fixture from the carton and check that all parts
and accessories are included as shown in the above illustration.
2. Turn off power
Before you start the installation, NEVER attempt any work without shutting
off the electricity until the work is done.
» Go to the main fuse, or circuit breaker, box in your home. Place the main
power switch in the “ OFF ” position.
» Place the wall switch in the “ OFF ” position.
3. Make assembly
A1
| A2
| A5
---|---|---
A3
| A4
Step A1 » Unscrew studs (F) from back plate (E), then set them aside for later installation.
Step A2 » Carefully pass the supply wires from the outlet box through mounting plate (C). Secure mounting plate (C) to the outlet box with mounting screws (A).
Step A3 » Make wire connections
Connect wires as below wires connection shown. PLEASE NOTE THAT GROUND WIRE IS BARE COPPER WIRE, NEVER CONNECT OTHER WIRES TO GROUND WIRES.
Connect ground wires according to the below chart
- GREEN GROUND SCREW
- OUTLET BOX GROUND
- FIXTURE GROUND
- DIMPLES
- CUPPED WASHER
Connect wires according to the below chart
| Connect Black or Red Supply Wire to: | Connect White Supply Wire to: |
|---|---|
| Black | White |
| *Parallel cord (round & smooth) | *Parallel cord (square & ridged) |
| Clear, Brown, Gold or Black without tracer | Clear, Brown, Gold or Black with |
tracer
Insulated wire(other than green) with copper conductor| Insulated wire(other
than green) with silver conductor
-
Note: When parallel wires (SPT I& SPT ll) are used. The neutral wire is square shaped or ridged and the other wire will be round in shape or smooth (see illus.)
- Neutral Wire
Twist wires together with plastic wire connectors until tightly joined, and wrap each connector with approved electrical tape. Be sure that no wire strands are exposed and then carefully tuck all wires into the outlet box.
Step A4 » Align the holes in back plate (E) and mounting plate (C), then secure them with the previously removed studs (F).
Step A5 »
- Install bulbs (Not included) (Please do not exceed the maximum wattage recommended on the socket.)
- Remove screws (G) from sockets (H), and carefully place glass shades (I) on sockets (H), then secure them with screws (G).
4. Check everything is installed properly, then you could turn on the light. Enjoy!
ORDERING PARTS
Keep this sheet for future reference in case you need to order replacement parts. All parts for this fixture can be ordered from the place of purchase. Be sure to use exact wording from illustration when ordering parts.
CLEANING
To clean, wipe the fixture with a soft cloth. Clean glass with a mild cleaner (such as mild and non-abrasive soap). Do not use abrasive materials such as scouring pads or powders, steel wool or abrasive paper.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>