GOLDEN LIGHTING 3072-SF Athena 3 Light Natural Black Semi Flush Ceiling Light Installation Guide

GOLDEN LIGHTING 3072-SF Athena 3 Light Natural Black Semi-Flush Ceiling

Light

For Customer Service, contact the place of purchase to arrange for replacement parts.

IMPORTANT:

• All installation work should be done by accredited professional.
• Shut off power supply at fuse or circuit breaker!
• Use only the specified bulbs. Do not exceed the maximum wattage!

Assembly Instructions

PREPARING FOR INSTALLATION
Carefully remove the new fixture from the carton as well as the yellow bag that holds all of the parts. See the important notes above. Shut off power at the circuit breaker and remove old fixture from the wall, including the old mounting strap.

• The mounting strap (B) contains several pairs of threaded holes and two sets of mounting screws (A & D). Hex nuts (C) should be attached to mounting screws (A) to secure them to the mounting strap (B). Find the pair of holes that matches the spacing of the holes on the junction box and your fixture’s canopy. Test canopy (F) on mounting strap (B) to ensure that the canopy will hang straight with enough of the threads of mounting screws (A) exposed for deco nuts (G) to fit securely. Adjust hex nuts (C) and place the fixture aside. Pull the house wires through the center of the mounting strap (B). Place mounting strap (B) over the junction box so that mounting screws (D) may be inserted. Secure mounting strap (B) to the junction box with mounting screws (D) and a screwdriver. Tighten the screws securely.

ASSEMBLING THE FIXTURE
No Assembly Required – This item arrives assembled and ready for installation. Please proceed to the next step.

CONNECTING THE WIRES

• Have an assistant support the fixture’s weight while completing the wiring. Refer to the wiring diagram and attach the fixture’s wires to the power supply wires from the junction box. Attach the fixture’s wires to the power supply wires from the junction box. Connect Hot to Hot (transparent wire with black inner thread, black, or smooth wire) Neutral to Neutral (transparent wire with white inner thread, white, or ribbed wire), and Ground to Ground (transparent wire with green inner thread, green wire, or copper). Twist the ends of the wire pairs together, and then twist on a wire connector. Make sure all twists are in the same direction. If there is no house ground wire coming from the junction box, locate ground screw (E) on the mounting bracket/mounting strap and wrap the fixture’s ground wire around the ground screw. Use a screwdriver to tighten the top of the ground screw (E) onto the wires and into the mounting bracket/mounting strap. Tuck the wires into the junction box.

How to Identify the Fixture’s Wires
Comment identifier les fils du luminaire

Hot: Smooth, Black, or Transparent with Black Inner Thread
Neutral: Ribbed, White, or Transparent with White Inner Thread
Ground: Copper, Bare Metal, Green, or Transparent Inner Thread

FINISHING THE INSTALLATION

• Push canopy (F) up to the ceiling over mounting strap (B) so that mounting screws (A) protrude through the holes in the canopy. Tightly thread decorative nuts (G) onto the exposed threads of mounting screws (A) to secure the canopy (F) until snug against the ceiling. 4. Install light bulbs (not provided) into sockets (H) in accordance with the fixture’s specifications. Do not exceed the maximum recommended wattage. Your installation is now complete. Turn on the power and test the fixture.

DIMENSION

Pendants & Linear Pendants Above a Kitchen Island
Center a linear pendant over the island. If hanging pendants, use one pendant for every 24″ of the island. Fixtures should hang at least 30″ above the countertop.
Pendants & Chandeliers Above a Dining Room Table
Fixtures should stay at least 30″ above the table. Use a fixture that is 12″ narrower than the width of the table.
Pendants and Chandeliers in Open Areas
The bottom should hang at least 7.5 feet from the floor. Allow clearance for any opening doors.

We appreciate your business and hope you love your new light!

Great lighting can add value and enhance the look of your home. To ensure the best lighting in your space, remember to layer your lighting. This ensures that your space will have both task and ambient lighting. Coordinating fixtures like sconces, flush mounts, and pendants can help you meet your layered lighting needs and reinforce your desired aesthetic. Install the lights with dimmers that allow you to control the level of light output at any given moment. Get function and style! Browse our site for coordinating lights and expert lighting advice. To help create the perfect look, visit www.GoldenLighting.com.Love your light and want to show it off? Follow us, share a picture, and tag us on Social.

Love your light and want to show it off?
Follow us, share a picture, and tag us on Social

• Facebook:  @GoldenLighting
• Instagram:  @GLFixtures
• Twitter:  @GoldenLighting1
• Pinterest:  @GoldenLighting

Get help, quick tips, and explore curated content

Documents / Resources

| GOLDEN LIGHTING 3072-SF Athena 3 Light Natural Black Semi Flush Ceiling Light [pdf] Installation Guide
3072-SF Athena 3 Light Natural Black Semi Flush Ceiling Light, 3072-SF, Athena 3 Light Natural Black Semi Flush Ceiling Light, Black Semi Flush Ceiling Light, Flush Ceiling Light, Ceiling Light
---|---

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>