GOLDEN LIGHTING 0902-4P Delphine 4 Light 19 Inch Burnished Chestnut Pendant Ceiling Light Instruction Manual
- June 10, 2024
- GOLDEN LIGHTING
Table of Contents
GOLDEN LIGHTING 0902-4P Delphine 4 Light 19 Inch Burnished Chestnut
Pendant Ceiling Light
Product Information
The product is a lighting fixture offered by Golden Lighting. The fixture comes with assembly instructions and is available in different styles such as linear pendants, chandeliers, and open area pendants. The product is designed to enhance the look of your home and add value to it. The fixture can be layered with other coordinating lights such as sconces, flush mounts, and pendants to achieve the desired aesthetic. The lights can be installed with dimmers to control the level of light output at any given moment.
Product Usage Instructions
To use the product, follow the below instructions:
-
Pendants and Linear Pendants Above a Kitchen Island: Center a linear pendant over the island. If hanging pendants, use one pendant for every 24 inches of island.
Fixtures should hang at least 30 inches above the countertop. -
Pendants and Chandeliers Above a Dining Room Table: Fixtures should stay at least 30 inches above the table. Use a fixture that is 12 inches narrower than the width of the table.
-
Pendants and Chandeliers in Open Areas: The bottom should hang at least 7.5 feet from the floor. Allow clearance for any opening doors.
-
Follow the assembly instructions provided with the product to prepare for installation, assemble the fixture, connect the wires, and finish the installation.
-
Hang the decorative chain on the open iron ring. Lock the nipple into the connector and fasten it with the nut. Put on the hardware cover and lock the finial.
-
Push canopy up to the ceiling and slide canopy loop collar up beneath the canopy. Tightly thread canopy loop collar onto canopy loop to secure canopy in place.
-
Install light bulbs (not provided) into sockets covers in accordance with the fixture’s specifications. Do not exceed the maximum recommended wattage.
-
Turn on the power and test the fixture.
If you need any help or quick tips regarding the product, or want to explore curated content, visit GoldenLighting.com. For customer service, contact the place of purchase to arrange for replacement parts.
Thank You for Choosing Golden Lighting for Your Lighting Needs!
Dimension
Pendants & Linear Pendants Above a Kitchen Island
Center a linear pendant over the island. If hanging pendants, use one pendant
for every 24″ of island. Fixtures should hang at least 30″ above the
countertop.
Pendants & Chandeliers Above a Dining Room Table
Fixtures should stay at least 30″ above the table. Use a fixture that is 12″
narrower than the width of the table.
Pendants and Chandeliers in Open Areas
The bottom should hang at least 7.5 feet from the floor. Allow clearance for
any opening doors.
We appreciate your business and hope you love your new light!
Great lighting can add value and enhance the look of your home. To ensure the
best lighting in your space, remember to layer your lighting. This ensures
that your space will have both task and ambient lighting. Coordinating
fixtures like sconces, flush mounts, and pendants can help you meet your
layered lighting needs and reinforce your desired aesthetic. Install the
lights with dimmers that allow you to control the level of light output at any
given moment.
Get function and style! Browse our site for coordinating lights and expert
lighting advice. To help create the perfect look, visit
www.GoldenLighting.com.
Love your light and want to show it off?
Follow us, share a picture, and tag us on Social…
Wiring
How to Identify the Fixture’s Wires
- Hot: Smooth, Black, or Transparent with Black Inner Thread
- Neutral: Ribbed, White or Transparent with White Inner Thread
- Ground: Copper, Bare Metal, Green, or Transparent Inner Thread
Get help, quick tips, and explore curated content
**Parts
**
For Customer Service, contact the place of purchase to arrange for replacement parts.
IMPORTANT:
- All installation work should be done by accredited professional.
- Shut off power supply at fuse or circuit breaker!
- Use only the specified bulbs. Do not exceed the maximum wattage!
Assembly Instructions
PREPARING FOR INSTALLATION
Carefully remove the new fixture from the carton as well as the yellow bag
that holds all of the parts. See the important notes above. Shut off power
at the circuit breaker and remove old fixture from wall, including the old
mounting strap. 1. From the parts bag remove the mounting strap assembly. One
end of nipple (F) should be attached to mounting strap (A) with washer (C) and
hex nut (D) in place. The other end should have canopy loop (H) attached.
Attach mounting strap (A) to the junction box using mounting screws (B) and a
screwdriver. Tighten securely. 2. Unscrew canopy loop collar (I) from canopy
loop (H). Pass canopy (G) over the mounted canopy loop (H) to test the height.
Approximately half of the canopy loop’s exterior threads should be exposed,
and the canopy loop collar (I) should fit snugly onto the canopy loop (H).
Remove canopy (G) and adjust the height of nipple (F) and canopy loop (H)
until the desired height is reached.
ASSEMBLING THE FIXTURE
3. Thread the middle rod (N) into the connector (W). Thread the middle column
swivel (M) onto the middle rod (N). Pull the wires until taut. Measure to
determine the correct number of chain links needed for proper hanging height.
If necessary, use a pair of pliers to open and remove any excess chain. Attach
one chain connector (K) to each end of chain (J). Attach one end of
chain/chain connector to top loop (L). Attach the remaining end of the
chain/chain connector to canopy loop (H). Close chain connectors (K) to
secure. Feed fixture wires from top loop (L) through the chain (every three
links or so), canopy loop collar (I), canopy loop (H), and canopy (G). Slide
canopy loop collar (I) and canopy (G) down onto the chain/wires. Pull the
wires until taut.
CONNECTING THE WIRES
4. Have an assistant support the fixture’s weight while completing the
wiring. Refer to the wiring diagram and attach the fixture’s wires to the
power supply wires from the junction box. Attach the fixture’s wires to the
power supply wires from the junction box. Connect Hot to Hot (transparent wire
with black inner thread, black, or smooth wire) Neutral to Neutral
(transparent wire with white inner thread, white, or ribbed wire), and Ground
to Ground (transparent wire with green inner thread, green wire, or copper).
Twist the ends of the wire pairs together, and then twist on a wire connector.
Make sure all twists are in the same direction. If there is no house ground
wire coming from the junction box, locate ground screw (E) on the mounting
bracket/mounting strap and wrap the fixture’s ground wire around the ground
screw. Use a screwdriver to tighten the top of ground screw (E) onto the wires
and into the mounting bracket/mounting strap. Tuck the wires into the junction
box.
FINISHING THE INSTALLATION
5. Hang the decorative chain (P) on the open iron ring (O). Lock the nipple
(S) into the connector (Q) and fasten it with the nut (R). Put on the hardware
cover (T) and lock the finial (U). 6. Push canopy (G) up to the ceiling and
slide canopy loop collar (I) up beneath the canopy. Tightly thread canopy loop
collar (I) onto canopy loop to secure canopy (G) in place. Install light bulbs
(not provided) into sockets covers (V) in accordance with the fixture’s
specifications. Do not exceed the maximum recommended wattage. Your
installation is complete. Turn on the power and test the fixture.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>