Eterna VECORDL18 Economy Recessed LED Downlights Instruction Manual

Model:
VECORDL6 / VECORDL12
VECORDL18 / VECORDL24
A guide for qualified electricians
INSTALLATION INSTRUCTIONS

Pack contents:

1 x Fitting
1 x Driver

These instructions are provided as a guideline to assist you.
PLEASE READ THESE INSTRUCTIONS BEFORE INSTALLATION AND RETAIN FOR FUTURE REFERENCE

READ THIS FIRST:

Check the pack and make sure you have all of the parts listed on the front of this booklet. If not, contact the outlet where you bought this product.
This light fitting must be installed by a competent person in accordance with the current building and IEE wiring regulations.
As the buyer, installer and/or user of this product it is your own responsibility to ensure that this fitting is fit for the purpose for which you have intended it. Eterna Lighting cannot accept any liability for loss, damage or premature failure resulting from inappropriate use.
This product is designed and constructed according to the principles of the appropriate British Standard and is intended for normal domestic service. Using this fitting in any other environments may result in a shortened working life, for example where there is prolonged periods of use or higher than normal ambient temperatures such as lighting public or shared spaces or in nursing / care home facilities.
Switch off the mains before commencing installation and remove the appropriate circuit fuse or lock off MCB.
This unit is suitable for indoor use only.
This product is suitable for installation on surfaces with normal flammability e.g. wood, plasterboard and masonry. It is not suitable for use on highly flammable surfaces (e.g. polystyrene, textiles).
Before making fixing hole(s), check that there are no obstructions hidden beneath the mounting surface such as pipes or cables.
The chosen location of your new fitting should allow for the product to be securely mounted and safely connected to the mains supply (lighting circuit).
Do not cover the fitting and/or transformer with any insulating materials.
Do not attach to surfaces which are damp, freshly painted or otherwise electrically conductive (e.g. metallic surfaces).
This product is designed for permanent connection to fixed wiring: this must be a suitable circuit (protected with the appropriate MCB or fuse).
When making connections ensure that the terminals are tightened securely and that no strands of wire protrude. Check that the terminals are tightened onto the bared conductors and not onto any insulation.
This product is double insultated. DO NOT CONNECT ANY PART TO EARTH.

LAMP REPLACEMENT:

This luminaire has a sealed LED lamp and is maintenance free, no lamp replacement is required.

IMPORTANT:
You are advised at every stage of your installation to double-check any electrical connections you have made. After you have completed your installation there are electrical tests that should be carried out, these tests are specified in the current IEE wiring and building regulations.

INSTALLATION:

This luminaire should be connected to a screw terminal block, minimum 2 pole, 240V 50Hz rated to suit the attached cable dimensions of 2 x 0.1sq.mm (conforming to BS6099).

1. Locate suitable position without obstructions (allow minimum 75mm around the hole for the spring clips) and minimum ceiling void height of 150mm. (see Fig.1 opposite).

2. Isolate mains.

3. Make a round fixing hole in the ceiling (see sizes below), ensuring that the hole is cut accurately, we recommend the use of a circular hole cutter.
   VECORDL6: 105mm diameter.
   VECORDL12: 155mm diameter.
   VECORDL18: 210mm diameter.
   VECORDL24: 285mm diameter.
   NOTE: Ensure cut-out holes are burr free before installations.

4. Make connection to driver.

5. Before feeding the luminaire into the hole, ensure the large spring clips point up. (See Fig. 2).

6. Feed the rest of luminaire into the hole in the ceiling ensuring it is flush to the mounting surface. (See Fig. 3).

7. Switch on and test the luminaire.

Number of switching cycles
before premature lamp failure| 15,000| 15,000| 15,000| 15,000
Warm-up time up to 60% of the full light output| 0.5s| 0.5s| <0.5s| <0.5s
Dimmable| No| No| No| No
Nominal beam angle| 115°| 115°| 115°| 115°
Rated power| 6W| 12W| 18W| 24W
Rated lamp lifetime| 25,000 hrs| 25,000 hrs| 25,000 hrs| 25,000 hrs
Lamp power factor| >0.5| >0.5| >0.9| >0.9
Lumen maintenance factor atend of nominal life| >70%| >70%| >70%| >70%
Starting time| <0.5s| <0.5s| <0.5s| <0.5s
Colour rendering| ≥80 Ra| ≥80 Ra| ≥80 Ra| ≥80 Ra
Colour consistency| Within a six step macadam ellipse| Within a six step macadam ellipse| Within a six step macadam ellipse| Within a six step macadam ellipse
Rated peak intensity| 91.81cd| 292.34cd| 430.65cd| 543.27cd
Rated beam angle| 115°| 115°| 115°| 115°
Voltage / Frequency| 240V~50-60Hz| 240V~50-60Hz| 240V~50-60Hz| 240V~50-60Hz

This product contains a Light Source of Energy Efficiency Class D
Not suitable for accent lighting

EVENTUALLY, YOU MAY WANT TO REPLACE THIS PRODUCT:
Regulations require the recycling of Waste from Electrical and Electronic Equipment (European “WEEE Directive” effective August 2005—UK WEEE Regulations effective 2nd January 2007).
Environment Agency Registered Producer: WEE/GA0248QZ.
WHEN YOUR PRODUCT COMES TO THE END OF ITS LIFE OR YOU CHOOSE TO REPLACE IT, PLEASE RECYCLE IT WHERE FACILITIES EXIST – DO NOT DISPOSE WITH HOUSEHOLD WASTE.

CLEANING:
Clean this fitting only with a soft dry cloth.
Do not use any chemical or abrasive cleaners.
IF YOU EXPERIENCE PROBLEMS:
If you believe your product is defective, please return it to the place where you bought it. Our Technical Team will gladly advise on any Eterna Lighting product, but may not be able to give specific instructions regarding individual installations.

Email: sales@eterna- lighting.co.uk / technical@eterna- lighting.co.uk
Visit our website: www.eterna-lighting.co.uk
Made in China

References

• Lighting.Co.Uk domain name is for sale. Inquire now.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>