Eterna BRICKLED LED Bricklight With Stainless Steel Frame Instruction Manual
- June 10, 2024
- Eterna
Table of Contents
Eterna BRICKLED LED Bricklight With Stainless Steel Frame
LED Lamp Specifications
- Luminaire lumens (with diffuser): 285 lm
- Lumens from chip (no diffuser): 700 lm
- Useful lumens: 265 lm
- Rated Wattage: 4.5W
- Rated luminous flux: 265 lm
- Nominal life time of the lamp: 30,000 hrs
- Colour temperature: 6000K
- Number of switching cycles before premature lamp failure: Not specified
- Warm-up time up to 60% of the full light output: Not specified
Product Usage Instructions
- Before installation, ensure that the lamp is compatible with your fixture and voltage supply.
- Turn off the power supply to the fixture before installing or removing the lamp.
- Gently insert the LED lamp into the fixture, making sure it is securely in place.
- Turn on the power supply and test the lamp to ensure it is functioning properly.
- If using a dimmer switch, ensure that it is compatible with the LED lamp and follow the manufacturer’s instructions for proper usage.
- To prolong the lifespan of the lamp, avoid frequent on/off switching and exposure to extreme temperatures.
- If the lamp fails to operate properly, turn off the power supply and replace the lamp with a new one of the same specifications
Pack contents
- 1 x LED bricklight fitting
- 1 x Stainless steel frame
- 1 x fixing kit (screws & plastic wall plugs)
- 2 x cable glands
Model : BRICKLED
READ THIS FIRST
Check the pack and make sure you have all of the parts listed on the front
of this booklet. If not, contact the outlet where you bought this product.This
product must be installed by a competent person in accordance with the current
building and IEE wiring regulations. As the buyer, installer and/or user of
this product it is your own responsibility to ensure that this fitting is fit
for the purpose for which you have intended it. Eterna Lighting cannot accept
any liability for loss, damage or premature failure resulting from
inappropriate use. Switch off the mains before commencing installation and
remove the appropriate circuit fuse or lock off MCB. This unit is suitable for
indoor and outdoor use. This product is designed for permanent connection to
fixed wiring: this must be a suitable circuit (protected with the appropriate
RCD and MCB or fuse).
These instructions are provided as a guideline to assist you. PLEASE READ
THESE INSTRUCTIONS BEFORE USING YOUR NEW FITTING PLEASE RETAIN FOR FUTURE
REFERENCE
EVENTUALLY, YOU MAY WANT TO REPLACE THIS PRODUCT
Regulations require the recycling of Waste from Electrical and Electronic
Equipment (European “WEEE Directive” effective August 2005—UK WEEE Regulations
effective 2nd January 2007). Environment Agency Registered Producer:
WEE/GA0248QZ. WHEN YOUR PRODUCT COMES TO THE END OF ITS LIFE OR YOU CHOOSE TO
REPLACE IT, PLEASE RECYCLE IT WHERE FACILITIES EXIST – DO NOT DISPOSE WITH
HOUSEHOLD WASTE. See website for more information on replacability and
recycling
IF YOU EXPERIENCE PROBLEMS
If you believe your product is defective, please return it to the place
where you bought it. Our Technical Team will gladly advise on any Eterna
Lighting product, but may not be able to give specific instructions regarding
individual installations.
LED Specifications
LED LAMP SPECIFICATIONS:
Luminaire lumens (with diffuser)| 285 lm
Lumens from chip (no diffuser)| 700 lm
Useful lumens| 265 lm
Rated Wattage| 4.5W
Rated luminous flux| 265 lm
Nominal life time of the lamp| 30,000 hrs
Colour temperature| 6000K
Number of switching cycles before premature lamp failure| 15,000
Warm-up time up to 60% of the full light output| <2s
Dimmable| No
Nominal beam angle| 120°
Rated power| 4.5W
Rated lamp lifetime| 30,000 hrs
Displacement factor| ≥0.9
Lumen maintenance factor at end of nominal life| ≥0.7
Starting time| <0.5s
Colour rendering| ≥80
Colour consistency| Within a six step Macadam ellipse
Rated peak intensity| 84cd
Rated beam angle| 120°
Voltage / Frequency| 240V~50Hz
Lumen efficacy: 63 lm / W
This product contains a Light Source of Energy Efficiency Class E
Not suitable for accent lighting
LAMP REPLACEMENT
The light source is designed to last the lifetime of the luminaire. The light
source contained in this luminaire shall only be replaced by the manufacturer,
service agent or a similar qualified person.
C AUTION, RISK OF ELECTRIC SHOCK.
INSTALLATION
Choose the location for your bricklight according to the conditions listed above. Your bricklight is designed to fit into the space occupied by one normal single house brick.
- Remove the stainless steel trim and diffuser. Take care not to lose any of the “O” ring seals on the screws.
- Remove the LED panel by pulling the tags which are fitted at each end of panel. See opposite.
- Offer the base of light fitting into the cavity into which you want it to fit and mark the location of the fixing holes on your mounting surface.
- Drill and fit wall plugs.
- Make cable entry hole using an appropriate hole cutter and drill out fixing points in the back of the housing.
- Fit the cable gland(s) to the case as required. Thread the supply cable through the gland and into the fitting.
- Make the electrical connections into the terminal block according to the markings:
- Brown wire to live terminal marked (L)
- Blue cable to neutral terminal marked (N).
- Re-fit the LED panel.
- Tighten the gland nut on the cable gland(s) to ensure they are tight and waterproof.
- Offer the case into the cavity once more and secure in position using the fixings supplied. If the fixings supplied are not appropriate to your installation select suitable alternatives.
- Fit the diffuser onto the fitting and secure using the two screws on the longest sides (top and bottom). Ensure that the small rubber “O” ring gaskets are in place.
- Fit the stainless steel trim; secure it in place using the two remaining screws.
- Restore the power and switch on.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>