TEXAS GTX2000 20V Series Strimmer User Manual

GTX2000 20V Series Strimmer

User Manual
Texas A/S – Cullen 22 – DK-5260 Odense S – Denmark
Tel. +45 6395 5555 – www.texas.dk – post@texas.dk
NOTE!
BATTERY AND CHARGER ARE NOTINCLUDED FOR SOLO MACHINES

GTX2000 20V Series Strimmer

| Warning:
Safety information about hazards that can result in personal injury
---|---
| Please read the user manual carefully before operating the machine.
| Wear safety goggles and ear protection
| Use work gloves.
| Do not expose the equipment to rain/water and store it indoor.
| Keep distance to other people, children and animals
| Warning:
Risk of flying objects
| Use shoes with non-skid soles
| Wear safety clothes
| Do not expose to temperatures above 45 degrees C.
| Must be recycled
| Do not expose the equipment to extreme heat or fire
| Waste electrical products must not be disposed of with the household waste.
This tool should be taken to your local recycling center for safe treatment

Original instructions

Spare parts
Spare part drawings for the specific product can be found on our website www.texas.dk If you find the part numbers yourself, this will facilitate more rapid service.
For purchase of spare parts, please contact your dealer.

Safety

How to read the manual
Please read this instruction manual carefully, especially the safety warnings marked with the symbol:
When using the product, the safety instructions must be closely followed. Read this manual carefully before starting the machine. Make sure that you know how to stop and  switch off the engine in case of accident. All instructions regarding safety and maintenance of the machine are for your own safety.
The warnings, precautions and instructions given in this manual, cannot cover all situations that the product can be placed in. The user must therefore present common sense and caution when using the product.

Safety in the work area

• Only use the product in clean and well lit areas

• Do not use the product in areas with explosive danger or where there is flammable fluids, gas or dust present.

• The person that uses the machine is responsible to other persons in the work area. Never use the machine when others, especially children or animals are near.

• This machine is an electric product. It is therefore important, that it ever comes in contact with water or is used in wet surroundings.

• Before using the machine, the dealer or other qualified person should instruct you in the use of the machine.

• Minors may not work the machine.

• The machine may only be lent to people who know how to work the machine. This manual should follow the machine under all circumstances.

• The machine may only be used by persons who are rested, well and fit. If the work is tiring, frequent brakes should be made. Do not use the machine under influence of  alcohol.

• Always check before start, that all bolts and nuts are tightened.

• Always wear eye protection when using the machine.

• Keep the trimmer head clean and free from wrapped grass or weed.

• Keep children and other persons at a distance of at least 5 meters from the work area.

• The battery should always be removed when:
  1. maintenance is made.
  2. the machine is left unattended

• During transport, the main switch must be switched off.

Identification of the machine and components

See Fig. 1 + 2

1. On/off switch
2. Safety lock
3. Operating handle
4. Battery pack*
5. Shaft adjustment collar
6. Safety hood
7. Spindle plate
8. Flower guard
9. Cutting blade
10. Cutting head
11. Lock for cutting head inclination
12. Lock for cutting head rotation
13. Front handle
14. Push button for adjusting front handle
15. Push button for capacity display
16. Disolay for remaining capacity
17. Locking button
18. Control lights
19. Battery charger*
20. Screw for fitting spindle plate
21. Screws for fitting safety hood

*Battery/charger are not included for solo machines

Unpacking and assembly

1. Unpack all parts and lay them on a flat, stable surface.
2. Remove all packing materials and shipping devices, if applicable.
3. Make sure the delivery contents are complete and free of any damage. If you find that parts are missing or show damage do not use the product but contact your dealer.  Using an incomplete or damaged product represents a hazard to people and property.
4. Ensure that you have all the accessories and tools needed for assembly and operation. This also includes suitable personal protective equipment.
5. Plug in the battery, by pushing it down until you hear a click
6. Remove the battery by push down the battery lock buttons and pull up
   NOTE: Always remove the battery before assembly and maintenance.

Fitting the safety guard. See Fig. 3
Turn the grass trimmer upside down. Mount the protective hood on the motor head, turn it to lock in position, then fix the safety guard with 2 screws (21)
This guard is intended to prevent loose objects from being thrown towards the operator. The guard also protects the operator from accidental contact with the trimmer head.
Check that the guard is undamaged and not cracked.
Replace the guard if it has been exposed to impact or is cracked.

Fitting the spindle plate. See Fig. 4
Place the spindle plate (7) onto the spindle and secure in place with the screw (20) provided. Note: Opposite thread (fasten by turning anti-clockwise)

Fitting the flower guard. See Fig. 5
Attach the flower guard (8) tom the motor housing.

Attaching and removing a blade. See Fig. 6+7
Place the big hole in the blade onto the blade mount in the bottom of the spindle plate, then pull the blade outwards so that the small hole is fitted into the mount.
To remove the blade by pushing the blade towards the centre of the spindle and then slide off.

Fitting the front handle. See Fig 8
Push the button (14) both sides and mount the front handle into the operating handle. Rotate the front handle to the required angle. Release the button and ensure the handle clicks into a locked position.

Setting the length of the unit. See Fig. 10
Slacken the shaft adjustment collar (5), pull the telescopic pole to the desired length.
Retighten the shaft adjustment collar again.

Setting the angle of the cutting head. See Fig. 11
Press in and hold the locking button (11). Tilt the cutting head (10) to the required position. Release the locking and ensure the head clicks into a locked position.

Battery

*Battery are not included for solo machines
Warning: Do not try to disassemble, short circuit or put it to extreme heat or fire, as it can cause serious inquiry and permanent damage to the battery!
The battery pack is not fully charged when delivered.
Charging

• Only use the original charger with art. no. 90063242
• Before the battery is being used the first time, it is recommended to fully charge it first.

Charge the battery.

Note: The indicator lights is only indicative indications, and is not accurate power indications.
Important: To protect the battery from total discharge, the machine will stop, when the battery is nearly empty.
The machine must not be started up again after automatic shutdown, as it can damage the battery.
The battery must be recharges before the work can continue.

Charger

A full charge takes around 60 min for 2.0 Ah battery and 120 min for 4.0 Ah battery.

• Only use the original charger.
• Do not try to charge other type of batteries in the charger, other than the original batteries with art. no. 90063245 (2.0 Ah) or 90063246 (4.0 Ah).
• Keep the charger in a dry and warm environment (10-25 degrees C) and only use it indoor. It should be connected to a normal 230V AC socket.
• Before the battery is being used the first time, it is recommended to charge it fully.
• The surface of the battery can become warm during charging. This is normal.
• Do not cover battery or charger during charging. Allow free ventilation of air.

Insert the battery into the slots of the charger and slide it into place until it locks. See Fig. 9

Status

| Charging
---|---
| Fully charged
| Evaluate
| Defective

Important: The charger will stop, when the battery is full. However, it is not recommended to leave the battery in charger for more than 24 hours.
It is recommended to drain the battery completely and fully charge it whenever possible, as it can increase the health of the battery. But partial charge will not damage the  battery.
To remove the battery from the charger, press the side buttons down and pull the battery out.
Before winter storage, the battery should be fully charged and kept warm at 10-20 degrees C. Charge it every 3 months. Make sure to keep ventilation holes clean and free from dirt.
Store the charger indoor between 5-25 degrees C.

Use

Before use, make sure that the battery is fitted properly with the battery lock in place.
To start the machine first press the safety lock (2) and then the on/off switch (1) Stop the machine by releasing the on/off switch.

Clothing

When using the machine, wear tight-fitting work clothes, strong working gloves, hearing protectors, safety goggles and boots with non-skid soles

Tips and advices

Trimming.
Hold the trimmer head just above the ground at an angle. It is the end of the line that does the work. Let the line work at its own pace. Never press the line into the area to be cut.

Cutting.
The trimmer is ideal for cutting grass that is difficult to reach using a normal lawn mower. Keep the line parallel to the ground when cutting. Avoid pressing the trimmer head  against the ground as this can ruin the lawn and damage the tool.
Do not allow the trimmer head to constantly come into contact with the ground during normal cutting, as this can cause damage and wear to the trimmer head.

Maintenance

Before any service and maintenance is done, the power must be disconnected, it means the battery removed from the tool.

• Remove the battery before you clean and store the machine.
• Clean the housing and other parts with a soft brush and a moist cloth. Never use aggressive cleansers or solvents.
• Prevent water from getting into the machine.

Storage

Store the trimmer dry and unavailable for children. It is recommended not to let it rest on the trimmer head.
Hang it on a wall in the handle.

Specifications

Warranty terms and conditions

The warranty period is 2 years for private end users in EU countries. Products sold for commercial use, only have a warranty period of 1 year.
The warranty covers material and/or fabrication faults.

Restrictions and requirements
Normal wear and replacement of wearing parts are NOT covered by the warranty.
Wearing parts, which are NOT covered for more than 12 months:

• Cutting guard and blade
• Battery: If the battery is not stored correct (frost-free and recharged every 3 months), the durability is only guaranteed for 6 months.

The warranty does NOT cover damages/faults caused by:

• Lack of service and maintenance
• Structural changes
• Exposure to unusual external conditions
• If the machine has been improperly used or overloaded
• Use of unoriginal spare parts.
• Other conditions where Texas cannot be held responsible.

Whether a case is a warranty claim or not is determined in each case by an authorized service center. Your receipt is your warranty note, why it should always be kept safe.

REMEMBER: The purchase of spare parts as well as any request for warranty repair, art. number (e.g. 90063XXX), year and serial number should always be informed.

• We reserve the right to change the conditions and accept no liability for any misprints.

Troubleshooting

place
Battery pack discharged?| Charging the battery pack
Battery pack defective?
Is the device defective?| Contact Texas customner service or service workshop

EC Declaration of conformity

Manufacture
Texas Andreas Petersen A/S
Hereby certifies that the following
Grass trimmer battery

GTX2000
 Is in compliance with the specifications of the machine directive and subsequent modifications

2006/42/EC – 2014/30/EU – 2000/14/EC amended by 2005/88/EC
Conforms with the following standards
EN 60335-1:2012+A11+A13, EN 50636-2-91:2014, EN 62233:2008, AfPS GS 2019:01 PAK
EN 55014-1:2017, EN 55014-2:2015

LA: 92 dB(A) LpA: 84,7 dB(A)
Vibrations Ah: 1.995 m/s2 (rear handle) / 2.089 m/s2 (front handle)
Serial numbers: 2301511001 – 2512519999

Texas Andreas Petersen A/S
Cullen 22 • DK-5260 Odense S
15.05.2023
Responsible for documentation
Johnny Loll

Johnny Lolk
Managing Director

Documents / Resources

| TEXAS GTX2000 20V Series Strimmer [pdf] User Manual
GTX2000 20V Series Strimmer, GTX2000, 20V Series Strimmer, Strimmer
---|---

References

• Salg af havemaskiner - Texas A/S

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>