Westinghouse Jessica Ceiling Fan Owner’s Manual

Westinghouse Jessica Ceiling Fan

Product Information

The Saynet-EI-Jessica-WH22 is a ceiling fan with a light kit that can be used both indoors and outdoors. It comes with a warning to observe safety precautions to reduce the risk of fire, electric shock, or injury to persons. The fan requires installation by an authorized electrician and can only be operated with a 2-pole switch  a 3mm contact opening. The installation height should be at least 2.3m, and the fan blades should not be bent and should be kept away from any objects in the area of rotation. The lamp should also be maintained at a safe distance from inflammable materials (curtains, wall, etc.) as indicated on the pictogram.

Product Usage Instructions

1. Read the entire instruction manual before beginning installation.
2. Use a 2-pole switch with a 3mm contact opening to operate the fan.
3. Only an authorized electrician should execute the installation.
4. The installation height should be at least 2.3m from the floor.
5. Maintain a safe distance between the lamp and inflammable materials (curtains, wall, etc.) as indicated on the pictogram.
6. Make sure the fan is securely fastened to the ceiling.
7. Do not use a dimmer type switch to control the fan speed.
8. Ensure that the fan blades are not bent and that there are no objects in the area of rotation.
9. Do not use this fan in the same room at the same time as a gas or fuel burning fire unless the flue has been tested under these conditions of use by a competent person.
10. If using the fan around children or persons with reduced physical, sensory or mental capabilities, ensure that they are given supervision or instruction concerning the safe use of the appliance.
11. The fan is suitable for use indoors and outdoors.
12. Before disassembling the light kit, ensure that the power supply is disconnected from the main supply. Power supply can only be turned on after installation is completed.
13. Do not remove the lampshade from the light bulb when the power supply is on.
14. Replace the light bulb only when the light kit has cooled down, and the power supply is disconnected from the main supply.
15. Ensure that the lampshade is in the fixed position when operating the product.
16. An appliance inlet being used with an appropriate connector for the power connection. The appliance inlet shall have at least the same degree of protection against moisture as required for the appliance.
17. If the supply cord is damaged, it must be replaced by the manufacturer, its service agent, or similarly qualified persons to avoid a hazard.

Note : Tools required for installation include a Phillips screwdriver, wire cutters, pliers, and a step ladder.

Jessica
Please write model number here for future reference:

SAFETY TIPS

READ AND SAVE THESE INSTRUCTIONS
WARNING: TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS, OBSERVE THE FOLLOWING:

1. Proceed with caution. Read all instructions before beginning the installation.

2. WARNING! This fan may be operated only with a 2-pole switch with a 3mm contact opening each.

3. Only an authorized electrician should execute the installation.

4. The installation height, i.e. the distance between the blades and the floor, should be at least 2.3 m.

5. Always maintain the distance between the lamp and inflammable materials (curtains, wall, etc.), as indicated on the pictogram.

6. Make sure the fan is securely fastened at the ceiling.

7. WARNING! Do not use a dimmer type switch to control the fan speed.

8. WARNING! To prevent injuries, make sure the blades are not bent and that there are no objects with in the area of rotation.

9. WARNING: Do Not use this fan in the same room at the same time as a gas or fuel burning fire, unless the flue has been tested under these conditions of use by a competent person.

10. This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and
    knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved. Children shall not play with the appliance. Cleaning and user maintenance shall not be made by children without supervision.

11. Suitable for use indoor and outdoor.

12. Before disassembling light kit, make sure the power supply is disconnected from the main supply. Power supply can be on only after installation is completed.

13. The lampshade should not be removed from the light bulb when the power supply is on.

14. Replacement of light bulb is only possible when the light kit has cooled down, and the power supply is disconnected from the main supply.

15. Make sure the lampshade is in the fixed position when operating the product.

16. Means for all poles disconnection having a contact separation that provide full disconnection under over voltage category III conditions must be incorporated in the fixed wiring in accordance with national wiring rules.

17. If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly qualified persons in order to avoid a hazard.

18. An appliance inlet being used with an appropriate connector for the power connection. The appliance inlet shall have at least the same degree of protection against moisture as required for the appliance.

TOOLS REQUIRED

• Phillips Screwdriver
• Wire Cutters
• Pliers
• Step Ladder

FEATURES

PREPARING FOR INSTALLATION

MOUNTING BRACKET INSTALLATION

WIRING OPTIONS BLADES INSTALLATION ****

DOWNROD MOUNT

MOUNTING BRACKET INSTALLATION

SECURE TO CEILING

LIGHT FIXTURE INSTALLATION

REMOTE CONTROL

HOW TO OPERATE YOUR CEILING FAN

Restore electrical power to the outlet box by turning the electricity on at the main fuse box. To make the fan operational, install 2 AAA 1.5V battery by removing battery cover on back of transmitter, installing battery, and replacing battery cover.

1. Adopt RF wireless digit emission technique, biunique controlled, coincident code rate is less than one millionth.
2. Receiver can be controlled by any angles of the transmitter in prescriptive space, unrestricted by direction with the memory function, the controller can save the status (light and direction) while the supply power OFF and resume to the original after re-load the power supply.
3. The transmitter and receiver are matched at the factory. Please follow the point 5 for re-match when the match is failed.
4. Matching process can be done by fan without the blades, the same transmitter can control another identical model ceiling fan.
5. Learning code matching mode is used between transmitter and receiver. Turn‘ON’ the supply power within 30 seconds and press the transmitter’s fan switch button ‘ ‘ for 5 seconds, it can load normally after hearing a long sound ‘bee’, which means learning successfully and it can works normally.
6. Learning mode is not accepted after turn ‘ON’ the supply power for 30 seconds.
7. When the transmitter can’t control the receiver, please check the battery switch touching normally or not, correction of the positive and negative, full or empty of the power.
8. When the transmitter can’t control the receiver, please check if any similar remote control is controlling the products nearly, then check whether they are working, because remote controlled product with the same frequency will disturb each other.
9. Low voltage of battery will affect the sensitivity of the transmitter and the signal reception accordingly, (the indicated light will flash out its warning when the battery with the low voltage), must replace if the battery is getting low voltage.
10. Please take out the battery from the transmitter when leaving unused for long time.
11. The maximum load of lighting will be 140W. Please connect the ground wire correctly, otherwise, it may cause the light micro-light or flash.
12. When installing the fan, the fan ceiling cover don’t press the antenna (or other wire), it is easy to breakdown the wire and short-circuited.

Remote Control Operation

1. Reversible switch- press and release the button controls direction, forward or reverse.

2. Fan switch– press and release the button, the remote turns fan off.

3. Speed switch-press and release the button. The remote operates the fan speed as follows:
   1-lowest fan speed,2-Med low fan speed, 3-Low fan speed; 4-Med fan speed;
   5-Med high fan speed; 6-Highest fan speed.

4. Timing control of the fan.

5. Light switch-Short press and release the button, the remote turns light ON.

6. Light switch-Short press and release the button, the remote turns light OFF.
   Note : Quickly turn Light ON/OFF, it will change Color Temperature.

7. LED indicated light. Pressed the button, the LED lighting.

OPERATION & MAINTENANCE

Operation
Speed settings for warm or cool weather depend on factors such as room size, ceiling height, number of fans and so on. The slide switch controls direction, forward or reverse.

• Warm weather/down position – (Forward) Fan turns counterclockwise direction. A downward air flow creates a cooling effect as shown in illustration A.
  This allows you to set your air conditioner on a higher temperature setting without affecting your comfort.

• Cool weather/up position – (Reverse) Fan turns clockwise direction. An upward airflow moves warm air off the ceiling area as shown in illustration B. This
  allows you to set your heating unit on a lower setting without affecting your comfort.

NOTE: Turn off and wait for fan to stop before changing the setting of the forward/reverse slide switch.

Maintenance

1. Because of the fan’s natural movement, some connections may become loose. Check the support connections, brackets, and blade attachments twice a year. Make sure they are secure.
2. Clean your fan periodically to help maintain its new appearance over the years. Do not use water when cleaning. This could damage the motor, or the wood, or possibly cause electrical shock.
3. Use only a soft brush or lint-free cloth to avoid scratching the finish. The plating is sealed with a lacquer coating to minimize discoloration or tarnishing.
4. There is no need to oil your fan. The motor has permanently lubricated bearings.

TROUBLESHOOTING GUIDE

If you have difficulty operating your new ceiling fan, it may be the result of incorrect assembly, installation, or wiring. In some cases, these installation errors may be mistaken for defects. If you experience any faults, please check this Trouble Shooting Chart. If a problem cannot be remedied, please consult with your authorized electrician and do not attempt any electrical repairs yourself.

TROUBLE

• If fan does not start:

SUGGESTED REMEDY

1. Check main and branch circuit fuses or circuit breakers.

2. Check terminal block connections as performed in step #10 of installation.
   CAUTION : Make sure main power is turned off.

3. Make sure forward/reverse switch is firmly in up or down position. Fan will not operate when switch is in the middle.

4. If the fan still will not start, contact a qualified electrician. Do not attempt to troubleshoot internal electrical connections yourself.

TROUBLE

• If fan sounds noisy:

SUGGESTED REMEDY

1. Check to make sure all screws in motor housing are snug (not over tightened).
2. Check to make sure the screws which attach the fan blade holder to the motor are tight.
3. Some fan motors are sensitive to signals from Solid State variable speed controls. DO NOT USE a Solid State variable speed control.
4. Allow “break-in” period of 24 hours. Most noises associated with a new fan will disappear after this period.

TROUBLE

• If fan wobbles:

SUGGESTED REMEDY
All blades are weighed and grouped by weight. Natural woods vary in density which could cause the fan to wobble even though all blades are weight-matched. The following procedures should eliminate most of the wobble. Check for wobble after each step.

1. Check that all blade holders are tightened securely to motor.
2. Make sure that canopy and mounting bracket are tightened securely to ceiling joist.
3. If blade wobble is still noticeable, interchanging two adjacent (side by side) blades can redistribute the weight and possibly result in smoother operation.

TROUBLE

• If light does not work

SUGGESTED REMEDY

1. Check to see that molex connector in the switch housing is connected
2. Check for faulty light bulbs.
3. If light kit will still not operate, contact a qualified electrician for assistance.

Meaning of crossed-out wheeled dustbin: Do not dispose of electrical appliances as unsorted municipal waste, use separate collection facilities. Contact you local government for information regarding the collection systems available. If electrical appliances are disposed of in landfills or dumps, hazardous substances can leak into the groundwater and get into the food chain, damaging your health and well-being. When replacing old appliances with new ones, the retailer is legally obligated to take back your old appliance for disposal at least free of charge.

Westinghouse Lighting,
Philadelphia, PA 19154-1029, U.S.A.
www.westinghouselighting.com

Westinghouse are trademarks of
Westinghouse Electric Corporation.
Used under license by Westinghouse Lighting.
All Rights Reserved.
Made in China

References

• Ceiling Fans | Lighting Fixtures | Lamps

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>