Immax 08965L KINGFISHER LED Table Lamp User Manual

Immax 08965L KINGFISHER LED Table Lamp

Product Information

The Immax KINGFISHER LED table lamp is equipped with Qi and USB wireless charging capabilities. It has an LED indicator that shows the charging status of your phone. The lamp has three brightness levels that can be adjusted according to your requirements. The lamp also has an alarm and calendar settings feature that allows you to set the time and date.

Product Usage Instructions

• To use the wireless charging function of the lamp, place your phone that supports QI wireless charging in the area designated for wireless charging on the table lamp base.
• Make sure that the indicator light turns red and the phone display shows a connection. If not, reattach the phone to the base or make sure it is correctly placed in the charging area. The LED indicator will turn green when your phone is fully charged.
• Do not disassemble the lamp and use only the original power adapter provided. Do not use the lamp in high temperature or humidity and avoid looking directly into the light source to prevent damage to eyesight. Do not use the lamp if the power cord is damaged, the lamp is mechanically damaged or wet, the lamp sparks or smokes, or if it flickers.
• To adjust the brightness of the lamp, press the brightness adjustment button to set it to your desired level. You can also turn off the display screen completely by holding down the button and turning it on again. Use a soft cloth to wipe the device and avoid using solvents or aggressive cleaners or chemicals.
• To set the alarm and calendar, press the set button on the lamp to access the setting mode. Press the set button again to select from hours, minutes, year, month, and day. Use the up or down button to set the desired time. Press the mode button or wait for a minute to interrupt the setting and save the desired settings. Use the down button to switch between 12H and 24H time format in normal mode.

Wireless charging

Place your phone that supports QI wireless charging on the table lamp base in the area designated for wireless charging. When the indicator light turns red and the phone display shows a connection, the phone will begin charging. If the phone does not display the connection information, make sure you have placed the phone correctly in the wireless charging area or reattach the phone to the base.

• If the LED indicator is red, your phone is charging. If the LED indicator is flashing red, the device is ready to charge.
• The green LED will light up when the mobile phone is fully charged. The mobile phone’s battery symbol also displays the full charge status. If the LED indicator is green, the phone is fully charged.

Technical Specifications

• Rated power consumption of LED luminaire : 8,5W
• Rated wattage of Qi charging: 10W
• Number of LEDs: 36pcs
• Luminous Intensity: 400lm
• Beam angle : 120°
• Illuminance: 2300lux from 30cm
• Input current: 12V/3A
• USB output: 5V 2.1A
• Power factor : >0.4
• Operating temperature : -20 to +50 °C
• Material: ABS, PVC
• Start-up time: instant on
• Dimensions: 18.213.936 (60)cm-cable length 150 cm
• Weight: 0.95kg
• Certifications : CE, RoHS
• Wireless charging : 10W (for charging mobile or other electronic devices)

Notice:

• Do not disassemble the lamp, it could cause injury electric shock
• Use only the original power adapter provided
• Do not use the lamp in high temperature or humidity
• Do not look directly into the light source, as damage to eyesight may occur
• do not use the lamp if:
• the power cord is damaged
• the lamp is mechanically damaged or wet
• the lamp sparks or smokes
• the lamp flickers

Environmental tips:

The symbol on the product or in the accompanying documentation means that used electrical or electronic products must not be disposed of with municipal waste. In order to dispose of the product properly, take it to designated collection points where it will be accepted free of charge. By properly disposing of this product, you will help conserve valuable natural resources and help prevent potential negative environmental and human health impacts that could result from improper waste disposal. For further details, contact your local authority or nearest collection point. Fines may be imposed for improper disposal of this type of waste in accordance with national regulations.

Maintenance :

Protect the equipment from contamination and pollution. Wipe the device with a soft cloth, do not use rough or coarse material.
DO NOT use solvents or other aggressive cleaners or chemicals.

IMMAX, Pohoří 703, 742 85 Vřesina, EU
www.immax.cz
Designed in Czech Republic, Made in China

REPLACEMENT BATTERY

DISPLAY SCREEN BRIGHTNESS ADJUSTMENT

• when the lamp is first switched on, the brightness is set to maximum
• by pressing this button, you can adjust the brightness according to your requirements
• 3 brightness levels can be set
• by holding this button the display can be switched off completely, then switched on again

Instructions for use

• Insert the power connector into the power connector on the lamp base
  Use only the original power adapter

• this button can be used to control the brightness of the lighting (more detailed instructions below

• you can tilt the lamp 90° in this direction – hold the lamp base

• the position of the lamp head can be adjusted within a range of 150°

• if you exceed this range, the lamp arm may be damaged

You can control the lamp with these buttons

Alarm and calendar settings

Time and date settings

1. in normal mode press the “set” button to access the setting mode, by pressing the “set” button again you can select from the following setting options: hours – minutes – year – month – day
2. Press “up” or “down” to set the desired time etc.
3. in the setting mode, press the “mode” button or for a minute to interrupt the setting. The desired settings are saved
4. in normal mode, press the “down” button to switch between 12H and 24H time format

Setting the Snooze function

1. in normal mode, press the “mode” button to activate the alarm function
2. in alarm mode, press the “set” button to activate the alarm settings: hours – minutes – snooze – music – exit
3. Press the “up” or “down” button to set the desired information
4. in alarm mode, press the “up” or “down” button to switch the alarm and Snooze functions on or off, and press the button again to switch between alarm on – snooze on – alarm off – snooze off
5. the alarm starts ringing at the set time for one minute, then the snooze function is activated and the alarm rings again. Press any button to turn off the alarm.

Setting the thermometer
In normal mode, press the “down” button to toggle between Fahrenheit (F) or Celsius (C)

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>