PPI Clavex GD Vertical Autoclave Controller with Graphic Display User Manual

PPI Clavex GD Vertical Autoclave Controller with Graphic Display

FRONT PANEL LAYOUT

Front Panel

Keys Operation

Normal Operation Mode.
| Cycle Start & Alarm Acknowledge| Press to Start / Abort Autoclave Cycle. In case of process under alarm condition, press to acknowledge and mute the alarm output.
| DOWN| Press to decrease the parameter value. Pressing once decreases the value by one count; keeping pressed speeds up the change.
| UP| Press to increase the parameter value. Pressing once increases the value by one count; keeping pressed speeds up the change.
| SET-UP| Press to enter or exit set-up mode.
****| ENTER| Press to store the set parameter value and to scroll to the next parameter.

PV Error Indications

ELECTRICAL CONNECTIONS

Analog Input

• AI-1: RTD Pt100 Sensor
• AI-2: Pressure Sensor

Digital Output

• DO-1: Heater Control
• DO-2: Air Valve Control
• DO-3: Event Alarm
• DO-4: Unused
• DO-5: Unused
• DO-6: Unused

Digital Input

• DI-1: Cycle Start
• DI-2: Door Open
• DI-3: Water Level
• DI-4: Alarm ACK
• DI-5: Unused
• DI-6: Unused

Operation Instruction

OPERATOR PARAMETERS

Parameter| Settings (Default Value)
Ster. Temp SP >>| Setpoint LO Limit to Setpoint HI Limit

(Default : 121.0 °C)

Air Outlet SP >>| Setpoint LO Limit to Setpoint HI Limit

(Default : 100.0 °C)

Ster. Time (HH:MM) >>| 0.01 to 99.59 (HH:MM) (Default : 00.10 min)
Change Password >>| 1 to 100

(Default : 0)

SUPERVISORY SERIAL PARAMETERS

Parameter| Settings (Default Value)
Device Id >>| 1 to 127

(Default : 1)

Baud Rate >>| 2400, 4800, 9600

19200, 38400, 57600

(Default : 9600)

Parity >>| None Even Odd

(Default : Even)

Serial Write >>| No Yes

(Default : No)

SUPERVISORY CONTROL

Parameter| Settings (Default Value)
Setpoint LO Limit >>| 0 to Setpoint HI Limit (Default : 90 °C)
Setpoint HI Limit >>| Setpoint LO Limit to 600.0 °C

(Default : 150.0 °C)

Overshoot Temp >>| Sterilization SP to Control SP HI

(Default :131 °C)

Cycle End Strategy >>| Immediate Stop Timer Based Stop Temp Based Stop

(Default : Immediate Stop)

Cycle End Timer >>| 1 to 60 Minutes (Default : 5 Min)
Cycle End Temp >>| Control SP LO to Sterilization SP (Default : 100.0 °C)
Ctrl Band >>| 0.1 to 99.9

(Default : 0.2 °C)

EOP Alarm Time (sec) >>| 0 to 250 Sec. (Default : 10 Sec)
SUPERVISORY STERILIZATION

Parameter| Settings (Default Value)
Steri. Stop Temp >>| Air Valve SP to Sterilization SP (Default : 120.5 °C)
Steri. Reset Temp >>| Air Valve SP to Sterilization SP

(Default : 120.0 °C)

SUPERVISORY PV OFFSET

Parameter| Settings (Default Value)
Temp Zero Offset >>| -50.0 to 50.0

(Default : 0)

Pressure Offset >>| -500 to 500 Counts

(Default : 0.0)

SUPERVISORY > PASSWORD

Parameters| Settings (Default Value)
Change Password >>| 1000 to 1999

(Default : 123)

SUPERVISORY > EXIT

Parameters| Settings (Default Value)
Exit Setup Mode >>| Yes No

(Default : No)

FACTORY TEMPERATURE INPUT

Parameter| Settings (Default Value)
Filter Constant >>| 0.5 to 60.0 Sec. (Default : 0.5 Sec.)
Temperature SP Offset >>| 0.0 to 10.0 ºC (Default : 0.0 ºC)
FACTORY > PRESSURE INPUT

Parameters| Settings (Default Value)
Pressure Indication >>| None Computed Measured

(Default : None)

Units >>| PSI KG/CM2 BAR EU

(Default : PSI)

Resolution >>| 1

0.1

0.01

0.001

(Default : 0.1)

4-20mA

0-5V

0-10V

1-5V

(Default : 0-5V)

Signal LO >>| ****

Default : Signal Low 0.000

Signal High 5.000

Signal HI >>
Range LO >>| 0 to 9999 Counts

(Default : 0.0)

Range HI >>| 0 to 9999 Counts

(Default : 100.0)

FACTORY DIGITAL INPUTS

Parameter| Settings (Default Value)
Remote Cycle Start >>| No Yes

(Default : No)

Water Level Detect >>| No Yes

(Default : No)

Water Level Logic >>| Open : Water Lo Close : Water Lo

(Default : Close : Water Lo)

Door Open Detect >>| Yes No

(Default : No)

Door Open Logic >>| Close : Door Open Open : Door Open

(Default : Close : Door Open)

FACTORY > FACTORY DEFAULT

Parameters| Settings (Default Value)
Set To Default >>| No Yes

(Default : No)

FACTORY > PASSWORD

Parameters| Settings (Default Value)
Change Password >>| 2000 to 2999

(Default : 321)

FACTORY > EXIT

Parameters| Settings (Default Value)
Exit Setup Mode >>| No Yes

(Default : No)

101, Diamond Industrial Estate, Navghar, Vasai Road (E), Dist. Palghar – 401 210.
Sales: 8208199048 / 8208141446
Support: 07498799226 / 08767395333
E: sales@ppiindia.net, support@ppiindia.net

References

• Factory Automation Products India | Automation Solutions in India

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>