Fysic FX-3930 Landline Phone with Large Photo Keys and Numbers User Manual

: June 11, 2024
: Fysic

Fysic FX-3930 Landline Phone with Large Photo Keys and Numbers

Product Information

The FX-3930 is a telephone with various features and functions for easy usage and installation. The user manual provides detailed information on the product’s network compatibility, maintenance, installation, number of memory, warnings, and tips. The telephone comes with a table stand, wall-mounting options, a handset, a phone cord, and photo buttons for customization.

Product Usage Instructions

Installation

Table Stand

To use the telephone on a table or desk, first, attach the table stand to the bottom of the phone by following these steps:

Hook one side of the stand into the bottom of the phone.
Push the other side of the stand into the bottom until the two tabs click in place. You may need to press them slightly.
To remove the stand, press the tab at the bottom and lift the stand out.

Wall Mounting

If you prefer to mount the phone on the wall, follow these instructions:

Drill two holes in the wall, 8.4cm apart.
Insert plugs and screws into the holes, leaving the screw heads protruding by 5mm.
Slide out the handset hook from the phone, turn it 180 degrees and place it back in the phone. This hook will hold the handset when not in use.
Hang the phone onto the screws using the keyholes at the back and push it down.
Secure the phone cord to the wall using cable clips.

Note: Do not use the table stand when mounting the phone on the wall.

Handset

Connect the handset to the phone by inserting one end of the coiled cord into the bottom of the handset and the other end into the left side of the phone. Press the plugs until they click in place.

Telephone

Insert one end of the phone cord into the bottom of the phone and the other end into the wall socket.

Photo Buttons

To customize the photo buttons:

Lift the cover of the photo button straight up.
Insert your own photo (25mm x 19.5mm) and replace the cover, making sure it fits properly.

Making Calls

Incoming Calls

You can adjust the ringer volume by using the switch at the bottom of the phone. The bell light will also flash when there is an incoming call, but it is not a button.

NETWORK COMPATIBILITY

This telephone is designed for use on the ‘public switched telephone networks (analog single line)’ of telephony and cable companies in all countries of the EU.
However, each provider could require a different connecting wire with plug.

MAINTENANCE

Only clean the housing with a moist cloth, never use chemical cleaning agents.
Never place the FX-3930 onto cellulose-treated surfaces; the rubber feet could leave tracks.

INSTALLATION

Table stand
When using the telephone on a table or desk, you should first attach the table stand to the bottom of the telephone.

first, hook this side of the stand into the bottom of the telephone (see 1)
now push the other side of the stand into the bottom until the 2 clips lock (see 2), if necessary depress these clips somewhat (see 3)

When you want to detach the stand again, press at 3 and remove in the direction of 4.

Wall-mounting

in a vertical line, drill 2 holes at a distance of 8.4 cm from each other and insert plugs and screws; let the head of the screws protrude for 5 mm
slide the receiver clamp out of the telephone, turn it 180° and place it back onto the telephone; this clamp will hold the receiver in case of wall-mounting
hook the telephone with the screw holes over the screws and press it downward
fix the telephone wire to the wall using the cable clips

In case of wall mounting, the table stand is NOT used.

Receiver

connect the receiver with the telephone by attaching one side of the spiral cable to the bottom of the receiver and the other side to the left side of the telephone
push in the plugs until they’re securely connected

The FX-3930 requires NO batteries

Photo buttons

By pulling the cover of the photo buttons straight up, you can place your own photos.
Photo dimensions: 25mm (h) x 19.5mm (w).
Pay attention to the shape of the cover when replacing it. When exaggerated, the whole will look as follows:

USING THE TELEPHONE

Incoming calls

adjust the call volume using the call volume switch at the bottom of the telephone:

: high call volume
: low call volume
: mute

the call indicator with also light up when you receive an incoming call; attention: this indicator is NO button

Answering calls

pick up the receiver to have your conversation with the receiver
or
briefly press the speaker button to answer the call in hands-free mode

Ending calls

put the receiver back onto the cradle if using the receiver for the current call
or
Press the speaker button again to end the call if using the speaker for the current call

Dialing numbers

pick up the receiver or turn on the speaker function

enter the desired phone number the number will be dialed directly

Redialling the last number

pick up the receiver or turn on the speaker function
Press the button to redial the last dialed number

*Dialling photo or memory numbers ()**

pick up the receiver or turn on the speaker function
Press the desired photo button or
Press the SOS or M1 or M2 or M3 button and the corresponding number will be dialled
for programming the memories, see paragraph

Call volume and tone

ATTENTION: EXCESSIVE VOLUMES CAN LEAD TO HEARING LOSS. IF MULTIPLE USERS ARE USING THE TELEPHONE, ALWAYS SET THE VOLUME TO NEUTRAL AFTER EACH CALL.

volume
Press to increase the volume or press to decrease the volume, these volume buttons control the volume of both the receiver and the speaker

amplifier
Press the +40dB button to switch on the amplifier, press again to turn off the amplifier, this function is only available in combination with the receiver

ATTENTION: DANGER DUE TO THE PRESENCE OF EXTREMELY HIGH MAXIMUM VOLUME

tone adjustment
Press the button the increase the high tones
attention: this function is only available in combination with an activated amplifier and the receiver

Muting the microphone

Press and hold this button during a call to turn off the microphone as soon as you release this button, the microphone will be switched on again

* and # buttons

the and are buttons mainly used for telebanking:

Press the button when requested to press the ASTERISK button
Press the button when requested to press the POUND button

R button

the R button (also called FLASH) is used to briefly interrupt the telephone connection; this brief interruption is used by some home or office switchboards for call forwarding; public switchboards use this button for telecom functions, such call waiting.

The bottom of the telephone is provided with a small switch for setting the duration of the interruption.

100 = 0.1 sec, this is the most common setting in the Benelux
300 = 0.3 sec, this setting is often used by company switchboards

For more information regarding this function, please contact your telephone service provider.

NUMBER MEMORY

Introduction

The FX-3930 offers a memory capacity of 10 direct telephone numbers, 6 of which can be provided with a photo of the subscriber. The maximum length of each memory is 16 digits. In addition to regular phone numbers, you can also program the numbers of mobile phones. The telephone uses the voltage of the telephone connection to store memories, eliminating the need for batteries. However, always make sure to keep the telephone connected. A short interruption is allowed, e.g. to quickly move the device, without losing any memories.

Programming

place the receiver next to the telephone
press 1x the STOR button
enter the number using the keypad
press 1x the STOR button
Press one of the 6 photo buttons to store the number as a photo button memory
or
Press one of the 4 direct memory buttons to store the number as a speed-dial number
put down the receiver

if you want to add a dial pause to the number, e.g. because the phone is connected through a home or office switchboard and 0 must be pressed first to get an outside line, then press the button at that position in the phone number; while dialing, the telephone will pause for at least 2.5 seconds

Dialing

pick up the receiver or switch on the speaker function
Press the SOS or M1 or M2 or M3 button
or
Press the desired photo button the number will be dialed

Changing or erasing
You can change a number by programming the new number in place of the old number. The old number will be overwritten.
You can erase a number by programming a non-existing number (e.g. 000) in the place of the old number. The old number will be erased.

WARNINGS AND USER TIPS

General

Carefully read the user’s manual and follow all directions.
Always remove the telephone plug from the telephone wall socket before cleaning the device.
Never install or use the telephone in wet or moist rooms or environments.
Ensure adequate heat dissipation; never cover the telephone nor place it directly next to a heat source.
Make sure not to damage the telephone wire and ensure nobody can fall or trip over it.
Never disassemble the telephone, only qualified personnel are allowed to do so.

Installation

Only connect/disconnect the telephone wire with/from the telephone when the telephone plug is removed from the wall socket.
Never install the telephone during thunderstorms.
Never install telephone connecting terminals in wet or moist environments.
Never touch non-insulated telephone wires unless disconnected from the telephone network

Environment
The packaging of this telephone can be collected as old paper. However, we recommend you to save it, to adequately protect the phone during transport. When replacing this telephone, please return it to the supplier to ensure environment-friendly processing.

PROOF OF WARRANTY

For the FYSIC FX-3930 telephone, you have a warranty of 24 months from the date of purchase. During this period, we guarantee the free repair of defects caused by material and workmanship errors. All this is subject to the final assessment of the importer. HOW TO HANDLE: If you notice any defect, first refer to the user’s manual. Please contact the supplier of this telephone or contact customer service of FYSIC on telephone number 073 6411 355 (Netherlands), 03 238 5666 (Belgium), 018 0503 0085 (Germany) or via the Internet
www.fysic.com.
THE WARRANTY BECOMES NULL AND VOID: In case of improper use, incorrect connections, leaking and/or incorrectly installed batteries, use of unoriginal parts or accessories, negligence, and in case of defects caused by moisture, fire, flooding, lightning, and natural disasters. In case of unauthorized modifications and/or repairs performed by third parties. In case of incorrect transportation of the device without adequate packaging and when the device is not accompanied by this warranty card and proof of purchase. The warranty does not cover connecting cables, plugs, and batteries. All further liability, especially concerning any consequential damages, is excluded

WWW.FYSIC.NLSERVICE@FYSIC.NL Commaxx B.V., Wiebachstraat 376466 NG Kerkrade, The Netherlands