LiGHTPRO 215A Juno Tube User Manual
- June 9, 2024
- LiGHTPRO
Table of Contents
LiGHTPRO 215A Juno Tube User Manual
Tube
User manual
Thank you for purchasing the Lightpro Tube.
This document contains the required information for correct, efficient and
safe use of the product. Consult the general manual of the Lightpro 12-volt
system and the user manual of your transformer for more information about the
set up and connection of your light plan.
Read the information in this manual carefully before using the product. Keep this manual near the product for consultation in the future.
PRODUCT DESCRIPTION
The Lightpro Tube can be used in combination with the Lightpro Juno Tube. It
can be placed in the ground using the supplied ground spike, but can also be
used for wall mounting. This product may only be used as outdoor lighting in
combination with the Lightpro
12-volt system. Any alterations made to the product may have consequences for
the safety, guarantee and correct functioning of the product and/or other
parts of the system.
SPECIFICATIONS
PACKAGING CONTENT
[Figure A]
- Tube
- Screws
- Dowel
- Allen keys
- Spacer
- Mounting blocks
- Cover caps
- Insert
- Plug
- Plug attachment
- Cover caps of the tube
Check if all parts are present in the packaging. For questions about parts,
service, and any complaints or other remarks, you can always contact us.
E-mail: info@lightpro.nl
INSTALLATION
[Figure B]
- Secure the tubes to each other with the insert and tighten the screws with the Allen key.
- Place the cover cap on the tube.
OPTION 1: INSTALLATION ON THE GROUND.
[Figure B]
- Place the plug attachment on the pipe and tighten the screws with the Allen key.
- Mount the connector on the connector attachment.
OPTION 2: WALL-MOUNTED INSTALLATION.
[Figure C]
Place the two mounting blocks in the desired location.
- Screw the screw into the wall at the desired location.
- Place the spacer over the screw.
- Screw the mounting block onto the screw.
[Figure D]
-
Slide the pipe through one of the mounting blocks.
Then slide the mounting blocks for the spotlight(s) onto the pipe. -
Slide the tube through to the 2nd mounting block on the wall. Make sure that the cable guide is at the back and then screw it onto the front of the mounting block.
-
Place the cover cap at the back.
MOUNTING SPOT
[Figure D]
- Place the friction ring [1] on the mounting block [6].
- Turn the spotlight with the cables as a package on the mounting block until you begin to feel resistance and slide the lamp to the desired position.
- Slide the mounting blocks for the spotlight(s) to the desired position.
- Secure them at the back with the set screw and place the cover cap [7].
[Figure E]
Route the cable by pushing it into the recess at the back of the tube.
Carefully slide the mounting blocks over the tube when the cable is in the tube to avoid damaging the cable.
Repeat this step in case more spots are mounted.
INSTALLATION OF THE LIGHTS
- Install the products in the desired position and lay the cables so they can be comfortably connected to the transformer or main cable.
- If products are provided with a drain hole for water, this hole must be pointing downwards.
- Use non-corrosive fixing materials (supplied as standard) if you want to bolt the products down.
- Connect the lights to the main cable by using the connector as shown in figure on page 5.
- Consult the manual of your transformer for more information.
SAFETY
-
Always fit this product so that it can still be accessed for servicing or maintenance. This product must not be permanently embedded or bricked in.
-
Turn off the system by pulling the plug of the transformer from the socket for maintenance.
-
Regularly clean the product with a soft, clean cloth.
Avoid abrasives that can damage the surface. -
Clean products with stainless steel parts with a stainless steel cleaning agent once per six months.
-
Do not use a high pressure washer or aggressive chemical cleaning agents when cleaning the product.
This can cause irreparable damage. -
Protection class III: this product may only be connected to safety extra-low voltage up to a maximum of 12 Volt.
-
This product is suitable for outside temperatures of: -20 to 50 °C.
-
Do not use this product in areas where combustible gases, fumes or liquids may be stored.
The product meets the requirements of the applicable EC, UK and EAEU guidelines.
For questions about parts, service, any complaints or other matters, you can
contact us at any time.
E-mail: info@lightpro.nl
Discarded electrical equipment must not be put in the household waste. If possible, take it to a recycling company. For details of recycling, contact a municipal waste processing company or your dealer.
5 year warranty – visit our website at lightpro.nl for warranty conditions.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>