LANCOM SYSTEMS GS-4554XUP Fully Managed Access Switches User Guide

: June 9, 2024
: LANCOM SYSTEMS

Table of Contents

GS-4554XUP Fully Managed Access Switches
Mounting & connecting
LED description & technical details
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

Hardware Quick Reference
LANCOM GS-4554XUP

GS-4554XUP Fully Managed Access Switches

LANCOM SYSTEMS GS 4554XUP Fully Managed Access Switches -
Console

Configuration interfaces RJ-45 & micro USB (Console)
Connect the configuration interface via the included micro USB cable to the USB interface of the device you want to use for configuring / monitoring the switch. Alternatively, use the RJ-45 interface with the provided serial configuration cable.
USB interface
Connect a USB stick to the USB interface to store general configuration scripts or debug data. You can also use this interface to upload a new firmware.
TP Ethernet interfaces 100M / 1G / 2.5G PoE+
Connect the interfaces 1 to 24 via Ethernet cable with at least CAT5e / S/FTP standard to your PC or a LAN switch.
TP Ethernet interfaces 100M / 1G / 2.5G PoE++
Connect the interfaces 25 to 48 via Ethernet cable with at least CAT5e / S/FTP standard to your PC or a LAN switch.
SFP+ interfaces 1G / 10G
Insert suitable LANCOM SFP modules into the SFP+ interfaces 49 to 52. Choose cables which are compatible with the SFP modules and connect them as described in the SFP modules mounting instructions: www.lancom-systems.com/SFP-module- MI.
OOB interface (rear panel)
Use an Ethernet cable to connect this out-of-band service port for an IP interface independent of the switching plane for management tasks or connection to a monitoring server.
QSFP+ interfaces 40G (rear panel)
Plug suitable LANCOM QSFP+ modules into the QSFP+ interfaces 53 and 54. Select cables suitable for the QSFP+ modules and connect them as described in the SFP modules mounting instructions: www.lancom-systems.com/SFP-module- MI.
Power supply module with mains connection socket (rear panel)
Supply the device with power via the power supply socket of the power supply module. Use the supplied power cord or a country-specific LANCOM power cord.
To remove the power supply module, disconnect the module from the power supply and then pull the plug out of the module. While pressing the release lever 11 to the left, you can pull the module out of the device by the handle 10 .
Additional slot for power supply module with mains connection socket (rear panel)
To install an additional power supply module, remove the corresponding module bay cover by loosening both associated screws and push the power supply module in as far as it will go until the release lever 11 audibly engages. Check by pulling the handle 10 that the module cannot be removed from the bay without the release lever 11 being pressed to the left.

LANCOM SYSTEMS GS 4554XUP Fully Managed Access Switches - Console
4

Before initial startup, please make sure to take notice of the information regarding he intended use in the enclosed installation guide!
Operate the device only with a professionally installed power supply at a nearby power socket that is freely accessible at all times.
The power plug of the device must be freely accessible.
Please note that support for third-party accessories (SFP and DAC) is not provided.
Please observe the following when setting up the device
→ For devices to be operated on the desktop, please attach the adhesive rubber footpads.
→ Do not rest any objects on top of the device and do not stack multiple devices.
→ Keep all ventilation slots clear of obstruction.
→ Mount the device into a 19” unit in a server cabinet using the provided screws and mounting brackets.
Both slide-in rails are attached as shown in the accompanying installation instructions www.lancom-systems.com/slide-in-MI.

Mounting & connecting

LANCOM SYSTEMS GS 4554XUP Fully Managed Access Switches - Console
2

➀ System / Fan / Stack / Link/Act / PoE

System: green| Device operational
System: red| Hardware error
Fan: red| Fan error
Stack: green| As manager: port activated and
connected with standby manager
connected
Stack: orange| As standby manager: port activated and connected to connected manager
Link/Act: green| Port LEDs show link / activity
PoE: green| Port LEDs show PoE status
➁ Mode / Reset button
Short press| Switching the port LED display
~ 5 seconds pressed| Device restart
Pressed until all portLEDs glow| Configuration reset and device restart
➂ ➃ TP Ethernet ports 100M / 1G / 2.5G PoE+ / PoE++
LEDs switched to Link/Act/Speed mode
Off| Port inactive or disabled
Green| Link 2500 – 1000 Mbps
Green, blinking| Data transfer, link 2500 – 1000 Mbps
Orange| Link < 1000 Mbps
Orange, blinking| Data transfer, link < 1000 Mbps
LEDs switched to PoE mode
Off| Port inactive or disabled
Green| Port enabled, power supply to
connected device
Orange| Hardware error
➄ SFP+ ports 1G / 10G

LED description & technical details

Hardware

Power supply	Exchangeable power supply (110-230 V, 50-60 Hz)
Environment	Temperature range 0–40° C; short-term temperature range 0-50° C;

humidity 10–90 %,
non-condensing
Housing| Robust metal housing, 1 HU with removable mounting brackets and slide-in rails,
network connections at front and rear, dimensions 442 x 44 x 440 mm (W x H x D)
Number of fans| 2
Interfaces
QSFP+| 2 QSFP+ 40 Gbps uplink ports for connection to superordinate core switches or content
servers, can also be configured as stacking ports via software
TP Ethernet| 24 TP Ethernet ports 100 / 1000 / 2500 Mbps PoE+
24 TP Ethernet ports 100 / 1000 / 2500 Mbps PoE++
SFP+| 4 SFP+ 1 / 10 Gbps, uplink ports for connection to superordinate core switches or content
servers, can also be configured as stacking ports via software
Console| 1 RJ-45 / 1 Micro USB
USB| 1 USB host
OOB| 1 OOB
Package Content
Mounting brackets| 2 19“ mounting brackets, 2 slide-in rails for rear stabilization in 19“ racks
Power supply| 1 exchangeable power supply LANCOM SPSU-920, expandable to 2 LANCOM SPSU-920
power supplies (hot swappable, for redundancy operation)
Cables| 1 IEC power cord, 1 serial configuration cable, 1 micro USB configuration cable

Hereby, LANCOM Systems GmbH | Adenauerstrasse 20/B2 | D-52146 Wuerselen, declares that this device is in compliance with Directives 2014/30/EU, 2014/35/EU, 2011/65/EU, and Regulation (EC) No. 1907/2006. The full text of the EU Declaration of Conformity is available at the following Internet address: www.lancom-systems.com/doc

LANCOM, LANCOM Systems, LCOS, LANcommunity and Hyper Integration are registered trademarks. All other names or descriptions used may be trademarks or registered trademarks of their owners. This document contains statements relating to future products and their attributes. LANCOM Systems reserves the right to change these without notice. No liability for technical errors and / or omissions.
111681 / 0323