Rain Harvesting DDIV02 Quickfit Diverter Installation Guide
- June 9, 2024
- Rain Harvesting
Table of Contents
Rain Harvesting DDIV02 Quickfit Diverter
PRODUCT DETAILS
The quickest way to start collecting water from your round downpipes. It’s as simple as making a hole in your pipe and then pressing the diverter inside. Then just connect it to your barrel and you’re done! No glue, no fuss. rainharvesting.com
WHAT’S IN THE BOX?
- Quickfit Diverter valve
- Quickfit Diverter round rubber collector
- 12mm (1/2”) garden hose fitting and seal
- 32mm (1 1/4”) hose fitting and seal Screws x 2
- Hole saw 35mm (1 3/8”)
Installation
TOOLS/MATERIALS YOU MAY REQUIRE
- Tape measure
- Marker pen
- Drill
- Utility knife
- Spirit level
- Liquid soap
HOW IT WORKS
- Determine and mark the position you would like to install your Diverter. Point the outlet in the direction you intend to route the hose. If you are connecting your Diverter to a rain barrel, make sure the diverter is mounted level to the inlet of the barrel, which will be just below the top of the rain barrel. Use a spirit level to check the height.
- Using the included hole saw, drill a hole in your downpipe at the marked position. Make sure to remove any burrs from the edge of the hole.
Suggested Installation Orientations
- Trim the tips off the collector if necessary depending on the size of the downpipe.
- Compress the rubber collector and push it through the hole, ensuring that it is oriented correctly to collect water. There is an indicator on the front of the collector to show the right way up. Using liquid soap to lubricate the rubber collector will make it easier to insert into the downpipe.
- Press the Quickfit Diverter onto the rubber collector. The mounting holes on the Quickfit Diverter body will align with the holes on the rubber collector.
- Screw the main housing to the downpipe using only moderate torque to ensure the screws do not strip out. This will seal the Diverter to the Downpipe.
- Screw on either the 12mm or 1 1/4” hose fitting onto the nozzle.
- Connect the hose to your rain barrel or rainwater tank as required.
- Make sure the On/Off knob is set to the position you require.
Product Specifications
All dimensions are in mm unless otherwise stated.
Maintenance
To keep your Quickfit Diverter performing at its best, ensure you install a rain head above the diverter to ensure that no leaves or debris can become lodged in your Quickfit Diverter. If you need to check your Quickfit Diverter, unscrew the diverter from your pipe. Use only a medium torque to ensure the screws don’t strip out. Carefully remove the rubber collector from the pipe. Hose or brush out any debris, then simply refit your Quickfit Diverter.
A common misconception about collecting rainwater is that all you need is a roof, a tank and some rain. This ‘tanking’ approach cannot always be relied on to deliver the volume – or quality – of water that you require. That is where we can help. With some thought, your rain harvesting system can provide you with cleaner water and lots of it. Whether you’re completely reliant on tank water or wanting to keep the garden green, our simple steps will help you achieve your goal.The Rain Harvesting approach to rainwater collection involves using tested and proven products to make quality rainwater available for use in and around your property. You don’t need much to get started and you will be surprised how easy it is to get the most out of your rainwater system.
How can we help you?
DISCLAIMER This product specification is not a complete guide to product usage. Further information is available from Rain Harvesting Pty Ltd and from the installation and Operating instructions. This specification sheet must be read in conjunction with the installation and Operating Instructions and all applicable statutory requirement. Product specifications may change without notice. © Rain Harvesting Pty Ltd rainharvesting.com
For more information or to find out how we can help, just give us a call on +61 7 3248 9600 Or visit our website at rainharvesting.com