iclever IC-JB21R 1800mah Jump Starter User Manual
- June 13, 2024
- iclever
Table of Contents
iclever IC-JB21R 1800mah Jump Starter User Manual
Product Accessories
Detailed Function Parameters
- Flashlight
- L.CD indicator
- Laptop charging port
- Power Button
- USB Output: 55V/2.4A
- Input(DC 15V/1A)
- 0n/Off Switch
- 2V Car Jumper Connector
- Air Compass
- Smart Jumper LED Light
- Boost Button
Jump Start a Vehicle
Thank you for your purchase on iClever IC-JB21R Jump Starter. Please read the instructions carefully before first use. Please keep this manual near to jump starter for future use.
Step 1
Insert the blue plug of the Smart Jumper Cables into the ENGINE START Input Socket.
- When the LED indicator Insert the blue plug of the Smart Jumper Cables into the ENGINE START Input Socket. 1) When the LED indicator flashes in red and green color alternately, the power or your jump starter is enough and please continue to the next step.
- If the indicator only flashes red color in a cycle (Each period it flashes 3 times and then pause ).the jump starter is in low battery. Please charge the starter in time.
**Step 2
**
Connect the RED clamp of the Smart Jumper Cables onto the positive “+” terminal of the vehicle battery and connect the Black one to the negative “-” terminal.
- If the LED indicator glows in green color, it works normally and please continue.
- If the LED indicator glows in other color, please refer to the ”Attention”and take action.
**Step 3
**
Ensure the smart jump cable clamps are connected to car battery correctly. Attempt to start the vehicle while the indicator lights turn to solid green. Let the jump starter cool down 2 mintues after each attempt.
**Step 4
**
As soon as the vehicle has started, remove the Smart Jumper Cables from the
Jump Starter. Then remove the Smart Jumper Cables from the battery terminals.
Attention
In the step 2, the LED indicator may turn to different colors according
different situation.
| Indicator status | Meaning | Action |
|---|---|---|
| Always in green | Works normally | Continue to the next step |
| Flashes in red | The (+) ( – ) areconnectedreversely | Remove the |
clamp fromthe car battery and then connect correctly
Always in redOR flashes inred & greencoloralternately| Vehicle batteryvoltage
is toolow (10.5 V ±0.3 V or less)| In emergency, you canforce to jump start
bypressing the Boost buttonat 3s until the indicatorchanges into green color.
NOTE: Before forcibly starting, please read the warning information
below.
WARNING:
Pressing the BOOST button at 3 seconds may be dangerous because the
protection function of smart clamp will be lost temporarily. In emergency, if
you need to jump start the vehicle forcibly, please ensure the RED clamp is
connected to “+” terminal of car battery while the Black Clamp is to the “-”
terminal.
Other indicator status and processing method
| Indicatorstatus | Meaning | Action |
|---|---|---|
| Flash in | The voltage of the | The cause of failure to |
| green | in-vehicle battery is | start the engine is not |
| higher than the voltage | battery rise. Please | |
| of the jump starter. | consider other causes. | |
| Reverse chargeprotection function isactivated. | ||
| Flash in | The overheat | Wait about 5-10 |
| red for 4 | protected function is | minutes, please use |
| times and | activated as the jump | after the temperature |
| pause | starter has been used | of the product drop |
| continuously. | down |
Work to charge mobile phone
Turn ON / OFF switch ON. Connect with the terminal such as a mobile phone *
tablet with the supplied USB charging cable and charge it.
USE the LED light
- Turn the switch to ON.
- Press and hold power button for 3 seconds;Steady
- flashlight beam
- Next quick press: SOS Strobe.
- Next quick press: Fast Strobe.
- Next quick press: Turn off flashlight.
- The red warning light flashes when the power button is pressed twice at high speed. Press it again to tum it off.
For safe use
- Please put the product away from children. Please use it properly according to the operation method described in the user manual
- When the red clip and the black clip are caught while connecting the cable to the main body, the short circuit protection function is activated, the indicator alternately blinks in red / green, and the output becomes zero.
- jump starter for other types of vehicles. It is forbidden to use the device for an aircraft, ship and so on
- Be sure to use genuine cable when connecting to this terminal charging terminal
- DO NOT immerse the product in water, operate the appliance close to the heat sources or in explosive atmospheres, such as in presence of flammable liquids, gases or dust
- If it is not used for a long time, please charge regularly (once in about three months),
- Do not drop the main body or accessories or give it a shock
- Do not place it near fire or heat sources.Do not disassemble or modify the product.
- If the product swells, there is a sound or an odor, stop using it immediately.
Specification
Capacity : 18000mAR / 66 6WH _ | Input : 15V~1A
Output for Vehicle : 12V/16V/19V | Start Current : 300A
Dimension: 748’354’1.73 Inch | Peak Curren t : 800A
USB Output : 5V=2.1A Battery Life : 1,000circles
USB Output : 5V/=2.4A Operating Temperature: -4 °F – 140°F
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>