APRVTIO ALD-200 Refrigerant Leak Detector User Guide

June 15, 2024
APRVTIO

APRVTIO ALD-200 Refrigerant Leak Detector

Technical Specifications

  • Product Name: ALD-200 Refrigerant Leak Detector
  • Principle: Heated diode detection
  • Life of Sensor: Longer compared to traditional leak detectors
  • Detection Accuracy: Higher compared to traditional leak detectors
  • Operation: Easy to operate
  • Refrigerants Detected: Wide range

Detection

Slowly move the probe at a distance of 0.25 inch near the suspected leak area, maintaining a speed of approximately 3 inch/sec.

The ALD-200 Refrigerant Leak Detector is a hand-held leak detector that uses the heated diode detection principle. Compared with the traditional leak detector, its sensor has a longer life, higher detection accuracy, is easier to operate, and can detect a wider range of refrigerants. The ALD-200 has an ergonomic design and a large LCD screen for easy viewing.

Structure

  1. Flexible probe
  2. Case
  3. Probe tip
  4. USB Port
  5. Buzzer
  6. Battery
  7. Peak
  8. Leak
  9. Sensitivity
  10. Button

Setup

  • Check the device has sufficient battery level. Turn on ( on/off button ) and wait for 30 seconds before testing.

  • Adjust the sensitivity ( sens ).APRVTIO-ALD-200-RefrigerantLeakDetector-fig-2

  • Slowly move the probe ( approx 3 inches/sec ) at a distance of 0.25 inches near the suspected leak area .

  • The screen will show the intensity of the leak and the audible tone will change to a siren sound.APRVTIO-ALD-200-RefrigerantLeakDetector-fig-3

Key Operation

  • Detection: When a leak is detected, the screen will show the intensity of the leak and the audible tone will change to a siren sound.
  • On/Off button: Press the button for 2 seconds to power on/off the device.
  • RSET button: Long press the button for 3 seconds to reset the sensitivity benchmark.
  • PEAK button: Press the button to record the maximum value of leakage.
  • Sensitivity button: Press the button to adjust sensitivity levels. By default, sensitivity is set to medium.
  • MUTE button: Press the button to turn on/off the buzzer.

Specifications

  • Sensor type :heated Diode
  • Sensor life : 500 hours
  • Max sensitivity : 4 g /yr
  • Alarm mode: Sound, light and LCD
  • Battery: Built-in rechargeable lithium battery 3.7 V 3000 mAh
  • Working time: Continuous 6 hours
  • Charging time: 4 hours
  • Charging current: 5V DC 1A
  • Operating environment: -10°C to 52°C /Relative humidity (20% to 85% RH)
  • Storage temperature : -20°C to 60°C
  • Weight: 415 g
  • Dimension: 201x86x38 mm
  • Certification: SAE_J1627, SAE_J2791, SAE_J2913, EN14624, 2012 CE Certification

Notices

  • Do not submerge the product in water or allow water to enter the intake of the probe.
  • Do not expose the product to temperatures exceeding 60°C.
  • Do not leave the product in direct sunlight for long periods.
  • Do not dismantle or attempt repairs of the product without authorization.
  • Do not change or replace the included lithium battery.
  • Do not leave for more than 6 months without charging the battery to prevent damage.
  • Do not use on objects with a charge or appliances connected to a power source.
  • Ensure the filter is present and clean before performing a test.
  • Ensure there is enough power before performing a test.
  • Use only the supplied charging cable.
  • Avoid the inhalation of refrigerant vapor. High concentrations are harmful and may lead to coma or death.

Frequently Asked Questions

  • Q: Can I submerge the product in water?
  • A: No, do not submerge the product in water or allow water to enter the intake of the probe.
  • Q: Can I use the product on objects with a charge or appliances connected to a power source?
  • A: No, do not use the product on objects with a charge or appliances connected to a power source.
  • Q: What should I do before performing a test?
  • A: Before performing a test, ensure that the filter is present and clean. Also, make sure there is enough power before performing a test.
  • Q: Can I use any charging cable to charge the product?
  • A: No, use only the supplied charging cable to charge the product.
  • Q: Is it safe to inhale refrigerant vapor?
  • A: No, avoid the inhalation of refrigerant vapor. High concentrations are harmful and may lead to coma or death.

SCANER

Technical Specifications

Video Instruction

APRVTIO-ALD-200-RefrigerantLeakDetector-fig-7

https://aprvtiotech.com/
sales@aprvtiotech.com
+1 713 701 1986

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals