RAIN HARVESTING RHSTR03 Leaf Eater Stream Shield Installation Guide

Leaf Eater Stream Shield Installation and Specification Guide

PRODUCT DETAILS

Prevent leaves and debris entering your downpipes and reduce maintenance with this sleek, leaf shedding rain head.
The open-faced design incorporates a splash shield which reduces water or debris bouncing off the screen onto any areas below.
The open design allows easily visibility of the mesh for simple maintenance.

Installation

WHAT’S IN THE BOX?

• Leaf Eater Stream Shield cover
• Leaf Eater Stream body
• Leaf Eater Stream screen

TOOLS/MATERIALS YOU MAY REQUIRE

• Tape measure
• Marker pen . Saw

HOW IT WORKS

The Shield reduces splashing from the rain head to increase the volume of rainwater you capture. Keep leaves out of your rainwater system with the mosquito proof screen.

LEAF EATER STREAM SHIELD INSTALLATION

1. Locate the position at which you want to install your Leaf Eater Stream rain head. This may be directly under your gutter/eave or mid-way down your vertical downpipes. Wherever you choose to install it, your
   Leaf Eater Stream rain head must be a minimum of 500mm above your tank inlet and tank overflow pipe.

2. Cut your downpipe where you want the bottom outlet of the Leaf Eater Stream rain head to sit.

3. Make the second cut like shown above (Figure 1). Ideally, the pipe should be offset 30-50mm above the screen to give you the best performance. Ensure all cut edges are clean and smooth.

4. Lower the Leaf Eater Stream onto the pipe (Figure 2). For added stability, fasten it to the wall with a screw through the rear face of the body.

5. Install the Shield cover onto the Leaf Eater Stream body by sliding it up the top pipe and lowering it into position so the bottom skirt sits in the corresponding channel between the screen and body.

6. If desired, you can paint your rain head to match your downpipes and/or building.

Product Specifications

All dimensions are in mm unless otherwise stated.
Fitting guide:
F = Female / Socket Fitting
M = Male / Spigot Fitting (Pipe size)
IP = In-Pipe Fitting

Maintenance

Occasionally your Leaf Eater Stream might require some maintenance.
Simply remove the cover to access the screen and brush off the screen, or remove the screen entirely for easier cleaning.
After cleaning, replace the screen into the body, making sure the it is evenly seated.
Replace your Shield Cover by sliding it up your inlet pipe and lowering into position so that the lower skirt sits in the gap between the screen and the body.

A common misconception about collecting rainwater is that all you need is a roof, a tank and some rain. This ‘tanking’ approach cannot always be relied on to deliver the volume – or quality – of water that you require. That is where we can help.
With some thought, your rain harvesting system can provide you with cleaner water and lots of it. Whether you’re completely reliant on tank water or wanting to keep the garden green, our simple steps will help you achieve your goal. The Rain Harvesting approach to rainwater collection involves using tested and proven products to make quality rainwater available for use in and around your property. You don’t need much to get started and you will be surprised how easy it is to get the most out of your rainwater system.
How can we help you?
COMPLIANCE
Australian Standard AS/NZS 4020:2005
(Testing of products for use in contact with drinking water)
DISCLAIMER This product specification is not a complete guide to product usage. Further information is available from Rain Harvesting Pty Ltd and from the Installation and Operating Instructions. This specification sheet must be read in conjunction with the Installation and Operating Instructions and all applicable statutory requirement. Product specifications may change without notice. © Rain Harvesting Pty Ltd

For more information or to find out
how we can help, just give us a call on +61 7 3248 9600
Or visit our website at rainharvesting.com

Documents / Resources

| RAIN HARVESTING RHSTR03 Leaf Eater Stream Shield [pdf] Installation Guide
RHSTR03 Leaf Eater Stream Shield, RHSTR03, Leaf Eater Stream Shield, Stream Shield
---|---

References

• Cleaner Water. More of it. | Rain Harvesting by BMCo US

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>