MSE AUDIO IPD4-BGM-II Series Four-Channel In-Ceiling Speaker with Seamless Grille Instruction Manual
- October 30, 2023
- MSE Audio
Table of Contents
MSE AUDIO IPD4-BGM-II Series Four-Channel In-Ceiling Speaker with
Seamless Grille
Product Information
The IPD4-BGM-II Series is a set of in-ceiling speakers designed for professional audio installation. The series comes in two models: IPD4-CM52 -BGM-II and IPD4-CM62-BGM-II. The package includes a speaker, a flexible conduit clamp, a cover plate, a magnetic grille, and an installation aid/paint mask. The speakers feature a tile bridge, secondary attachment point, Speed WingTM mounting arms, baffle, and grille safety restraint. The product comes with important safety instructions that need to be followed.
Important Safety Instructions
- Read these instructions.
- Keep these instructions.
- Heed all warnings.
- Follow all instructions.
- Do not use this apparatus near water.
- Clean only with dry cloth.
- Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.
- Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.
- Only use the attachments/accessories specified by the manufacturer.
- Unplug this apparatus during lightning storms or when unused for long periods of time.
- Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.
Box contents
- 1 Speaker
- 1 Flexible conduit clamp
- 1 Cover plate
- 1 Magnetic grille
- 1 Installation aid/paint mask
Warning
- SoundTube speakers must be installed by a professional audio installer/contractor. For safety and for optimum audio performance, installer must follow all directions issued by SoundTube Entertainment.
- Do not spec or install speaker near support beam, ventilation duct or other structure that may interfere with speaker function or dispersion.
Installation instriction
-
Unpack speaker & set aside grille assembly.
Ceiling preparation – For Tile Ceilings
-
Use included tile bridge to mark cutout in tile.
-
Use Rotozip or other tool to cut hole. Hole Diameter 266.7 mm (10.50 in)
Ceiling preparation – For Sheetrock/gypsum board ceilings
-
Use included tile bridge to mark cutout in sheetrock.
-
Use Rotozip or other tool to cut hole. Hole Diameters 266.7 mm (10.50 in)
Ceiling preparation – For all other ceiling types
-
Nail or screw bracket to joists. Secure conduit/signal wire away from hole in bracket. Once installed, complete finish work.
-
Use Rotozip or other tool to cut hole. Hole Diameter 266.7 mm (10.50 in)
-
Run signal wires through conduit, terminate with RJ45 connector, then plug into speaker. If local power is required at speaker (non-POE installation), connect appropriate DC power supply to barrel connector on speaker input panel. Contact SoundTube for questions about installations requiring local power.
-
Add up to 3 additional passive CM52-BGM-II or CM62-BGM-II speakers to the output speaker connector on the IP speaker. Set passive speakers to transformer-bypass setting.
-
To connect wires to the Euro-Block connector loosen the screws, insert a 1/4″ in of stripped wire and tighten the screws. Please make note of wire polarity in Step 5.
-
Tighten screw on terminal plate, and push conduit connector into knockout.
-
If required, a sheet-metal tab located on the rear panel of the speaker serves as a secondary point of attachment (cable not included).
-
Insert speaker into mounting hole with installation aid in place. Screw down both bolts on the baffle face to actuate the mounting wings. Firmly secure both bolts – do not over-tighten.
-
Attach grille safety clip by placing the large end of the clip over snap-fit post (1), then sliding clip until small end snaps into place around post (2).
-
Place grille onto baffle. (The grille is held in place by magnets in the baffle.)
-
Done!
FCC
This device complies with Part 15 of the FCC Rules / Industry Canada license-
exempt RSS standard(s). Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and (2) this device must
accept any interference received, including interference that may cause
undesired operation.
Changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more
of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
855.663.5600
913.663.5600
www.soundtube.com
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>