Telly Inc TYRC-1 Remote Control User Manual
- August 27, 2024
- Telly Inc
Table of Contents
Telly Inc TYRC-1 Remote Control
Product Specifications
- Title: Remote Control
- Manufacturer: Telly, Inc.
- Country of Origin: China
Product Usage Instructions
- Step 1: Insert batteries into the remote control.
- Step 2: Point the remote control towards the device you want to operate.
- Step 3: Press the appropriate buttons to control the device.
Frequently Asked Questions (FAQ)
Q: How do I program the remote control for a new device?
A: To program a new device, follow the instructions provided in the
user manual specific to that device.
General information
| Title | Remote Control |
|---|---|
| Manufacturer | Telly, Inc. |
| Country of origin | China |
Unit standard
| NO | Check Item | Description/Specification |
|---|---|---|
| 1 | Standard Voltage | DC 3.0V |
| 2 | Operation Voltage | DC 2.2V~3.6V |
| 3 | Operation temperature | -10℃A-50℃(≤95%RH)，86-106Kpa |
| 4 | Storage temperature | -20°C~60°C |
| 5 | Battery type | UM-4,AAAbattery*2 |
| 6 | Netweight(No battery, no packaging) | Subject to sample±3% |
Specification
Visual specification
| No. | Check Item | Description/Specification |
|---|---|---|
| 1 | Appearance | Refer to appearance drawing |
| 2 | Case material | ABS |
| 3 | Rubber KEY PADmaterial | Rubber |
| 4 | Nameplate material | N/A |
| 5 | Assembly | No moving parts inside the RC |
| 6 | Plastic visual | No visual of scratch, crack, contamination and deformation |
| 7 | Printing visual | Printings and Indications are same as drawing |
Remark: For all visual standard should refer to approved sample
Mechanical specification
Electronic specification
Transport and storage conditions
The packaging of remote control should avoid rain, snow or strong pressure during shipment.
The remote control should be stored undertemperature of -10 ℃ ~ +55℃, relative humidity cannot exceed 80%, and also cannot be put in strong magnetic fields and harmful air, or close to corrosive substances.
Reliability testing
Remote control appearance
Remark:
We’ll make mass production according to approved sample.
Product function description
Function Introduction
Bluetooth buttons, Google Voice, infrared, G-sensor, backlight, buzzer,
support for Findme function.
hardware component
- IC： TLSR8251F512ET48 pilot lamp： Large screen Key backlight as indicator
- Backlight： white LED 4 IR： ：1 Antenna type： PCB on-board antenna
- Sensor： ICM-42670-P Buzzer： JBE8540X-0327-16RS
Functional requirements
major function
- The IMU function is required. The IMU needs to save power and minimize power consumption
- Support OK+BACK/DOWN+BACK key combination reporting functio
- Use private voice
- SmartRCU and manual infrared learning are not supported
- Support remote control power reading service
- The hardware needs to support infrared emission, mainly reserving the subsequent need to support infrared emission when Bluetooth is disconnected• Infrared when Bluetooth is disconnected•
Backlight
- Corresponding backlight when large screen is pressed
- The corresponding backlight is on when the small screen is pressed
- Large screen
- Small screen
other
- The usage ID of customized application keys ranges from 0x0200 to 0x0210
- The maximum value of key value cannot exceed 0x028c
Functional requirements
Pair and connect back
Key function
Key name and key value are as follows
Google ATV voice function
-
Compliant with USB HID AUDIO standard protocol
-
Speech sampling rate: 16K/16BIT, speech encoding format PCM bitstream
-
Press and hold the voice button to turn on voice. After turning on local voice, release the voice button orreceive a command from the host to turn off voice (08 06 00), and the remote control will exit voice.
-
G-sensor wake-up backlight function
Shake the remote control to wake up the backlight, send commands to the host, and the host controls the backlight to light up. -
Findme function Findme
-
Findme UUIDMain Service UUID: 0000AA0-3C17-D293-8E48-14FE2E4DA212Characteristic UUID: 000B002-0000-1000-8000-00805F9B34FB
-
The findme function allows for custom hid reports. By writing a byte to the remote control through APK,the buzzer will continue to sound for 30 seconds. Press any key to exit.
-
Sending data 0x01 activates the findme function, and the buzzer emits beeps Sound.
-
Send data 0x02 to disable the findme function.
Low power consumption mode
| Power supply mode | AAA*2 2节 AAA 7号干电池 |
|---|---|
| Low voltage | VBAT 2.3V 0.2V |
| Serious power | VBAT 2V Prohibit work |
| Power acquisition | Support the normal power reading service for the host side |
to read the battery power of the remote controller
Electricity service
The remote control supports ota (online) upgrade
In order to adapt to new requirements or changes, the remote controller needs to support ota upgrade. The upgrade package is sent to the Bluetooth remote controller through the box end.
Description of indicator light
No connection button| The indicator light slowly flashes 6 times and then goes
out (250ms on and 250ms off)
---|---
Pair| The pilot lamp light flashes rapidly during pairing (100ms on and 100ms
off) The indicator light of successful pairing is always on for 3s and then
off
The pairing fails, and the indicator flashes for 60s and then goes out.
Connected| The indicator light is not on
Reconnection| The successful reconnection indicator light flashes quickly
once, stays on for 3 seconds, and then goes off
Low voltage| The indicator light flashes slowly for 3 times and then goes out
(500ms on and 500ms off)
Serious power shortage| Stop working (no prompt), and normal
operation can be resumed after the power is restored.
Priority| Pairing>Low power>No connection button>Link
Backlight| It only lights up in pairing mode, and in other cases, it is
controlled by the host.
Remote control Dimensions
Packing drawing
FCC STATEMENT
- This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
- This device may not cause harmful interference, and
- This device must accept any interference received, including interference that may cause undesired operation.
- any Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful
interference in a residential installation.
This equipment generates uses and can radiate radio frequency energy and, if
not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
FCC Radiation Exposure Statement
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>