LORGAR TRIX-510 Pro Nintendo Switch Instruction Manual

: June 9, 2024
: LORGAR

Table of Contents

Overview
Instruction
DEVICE EXTERIOR
SPECIFICATIONS
SAFE USE GUIDELINES
GAMEPAD USE
DEVICE CONNECTION FEATURES
BUTTON FUNCTIONS
VIBRATION AND BACKLIGHTING
XINPUT AND DINPUT MODES
TROUBLESHOOTING
WARRANTY SERVICE
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

LORGAR TRIX-510 Pro Nintendo Switch Instruction Manual

Overview

Instruction

| A| B| Y| Start| Back
---|---|---|---|---|---
Nintendo Switch| B| A| X| +| −
Nintendo Switch| 1| 2| 3| 4| 5| 6| 7| 8
---|---|---|---|---|---|---|---|---
LED| | | | | | | |
**| X| Y| B| A| Back
---|---|---|---|---|---
PS3| **| | | X| Select
Ps3| 1| 2| 3| 4| 5| 6| 7
---|---|---|---|---|---|---|---
LED| | | | | | |
| 1| 2| 3| 4| 5
---|---|---|---|---|---
| 100 %| 75 %| 50 %| 25 %| Ø
Xinput| Dinput
---|---
|

DEVICE EXTERIOR

①	Left joystick	⑨	Backlit right joystick
②	Back button	⑩	LT – left trigger, RT – right

SPECIFICATIONS

Connection: BT (5.0, up to 10 m, −30…−20 dBm, 0.001–0.01 mW) and USB Type-A/Type-C cable.
Battery: non-removable, lithium polymer, 600 mAh, 3.7 V, run time up to 8 h, charging time 2 h, via USB Type-C connector ⑪ (input 5 V / 500 mA DC, up to 2.5 W).
Operating and storage conditions: temperature −10…+45 °C, relative humidity up to 55 % (non-condensing).
Design features: 152×102×60.5 mm, 200 g, plastic.
Functional features: 16 buttons, 2 built-in vibration motors, backlit buttons A, B, X, Y ⑥ and right joystick ⑨. Scope of supply: LRG-GP510 gamepad, USB cable Type-A/Type-C (1 m), BT transmitter, quick start guide.
Purpose: gamepad for wired and wireless connection to devices with iOS 13.0 and above, Android 4.0 and above, Nintendo Switch, PS3, Windows 7 and above. Wired connection to Android is only available for OTG-enabled devices using the OTG adapter (not included). Wired connection to iOS, PS3 is not supported.

SAFE USE GUIDELINES

Read and follow these instructions before using the device.

Do not expose the device to high temperatures (from heaters, direct sunlight), high humidity, keep the device away from dust and liquids.
Clean the device only after disconnecting it from the power supply, use only a dry cloth for cleaning, do not use detergents, cleaning agents or solvents. Do not use a device that is heavily contaminated, defective, or overheated.
Do not disassemble or attempt to repair the device yourself. If it breaks, contact the service center.
If the battery is damaged or leaking, do not use the gamepad or touch the gamepad, battery, or leaking fluid.

GAMEPAD USE

Charging. Fully charge the battery before using it for the first time. Connect the USB cable to the USB Type-C connector ⑪ of the gamepad and to a power source: a device that supports the USB charging function or a wall charger (not included). The gamepad also charges while wired to PCs and consoles. The indicator ⑫ will light red while charging is in progress.
Switching on the gamepad and connecting it to devices.
| Wireless| Wired
---|---|---
Android| According to scheme A.| According to scheme B.
iOS| According to scheme C.| Not supported
PC| According to scheme D.| According to scheme E.
Nintend o Switch| Home menu of the console → “Controllers” → “Change Grip and Order”.Next – according to schemeF.| Home menu of the console → “System Settings” → “Controllers andSensors” → “Pro Controller Wired Communication”. Next – according to scheme G.
PS3| According to scheme H.| Not supported

The LED indicators ⑧ will light up if the connection is successful.

Switching off. Press and hold the Home button ④ for 5 seconds. A gamepad connected via BT turns off automatically after 5 minutes of inactivity. A gamepad connected via USB cable does not automatically disconnect when idle.

DEVICE CONNECTION FEATURES

Currently, the Android and iOS operating systems do not support the vibration function on the gamepad.
When gamepad is connected to the Nintendo Switch, the buttons change their function (see table 1 on page 6). Up to 8 gamepads can be connected to the Nintendo Switch. The combination of LED indicators ⑧in multiplayer game corresponds to the player’s number (see table 2 on page 6).
When gamepad is connected to the PS3, the buttons change their function (see table 3 on page 6). Up to 7 gamepads can be connected to the PS3. The combination of LEDs ⑧ in multiplayer game corresponds to the player’s number (see table 4 on page 6).

BUTTON FUNCTIONS

Button R3. Pressing the right joystick ⑨ in the rightmost position corresponds to pressing the R3 button.
L3 button. Pressing the left joystick ① in the leftmost position corresponds to pressing the L3 button.
Turbo button ③. The Turbo mode is used for automatic continuous repetition of the
command.
Press and hold the desired button (A, B, X, Y ⑥, LB, RB ⑬, LT, RT ⑩) and press the
Turbo button ③ to assign the turbo mode. A short vibration signal is emitted when the Turbo mode is activated. The backlight of the right joystick ⑨ flashes red all the time the turbo mode is on.
To cancel Turbo mode, press and hold the button for which it was selected and press the Turbo button ③. The backlight of the right joystick ⑨ lights blue when Turbo mode is off.
When gamepad is connected to the Nintendo Switch, the Turbo button ③ can be used as a screenshot button, to view video duration, to switch Turbo mode functions. To switch the Turbo mode functions, press and hold the R3 button and then press Turbo ③.
The Home button ④is used to exit the game, go to the home page, and turn off the gamepad.
The reset button ⑮ is designed to reboot the gamepad. Use a thin object (special pin, paper clip, etc.) to press it.

VIBRATION AND BACKLIGHTING

You can set the gamepad vibration and backlighting of the A, B, X, Y ⑥ buttons to one of 5 levels (see table 5 on page 6).
To change the vibration power by one level, press and hold Turbo ③, then press the
D-pad button ⑦ up to increase or down to decrease.
To change the backlight brightness by one level, press and hold the LB + RB ⑬

R3 buttons and press the D-pad button ⑦ up to increase or down to decrease. Hold the LB + RB ⑬ buttons for 5 seconds to turn off the backlight.

XINPUT AND DINPUT MODES

In Xinput mode, the gamepad buttons are automatically synchronized with the game control. In Dinput mode, the gamepad buttons are set manually for each game. Switching from Xinput to Dinput mode
When wirelessly connected, press and hold the Turbo button ③ to switch modes. For a wired connection, press and hold the A + B buttons ⑥ and then press the Home button ④. See table 6 on page 6 for indication of modes.

TROUBLESHOOTING

Gamepad does not turn on. Check the battery charge. Check that the USB cable is working properly. Check that the charger is working properly. Check that the connectors of the device to which the gamepad is connected for are working properly.
The gamepad does not respond to commands. Check the USB connection. Try connecting the gamepad to a different USB connector. Restart your PC/console/smartphone/tablet. Press the reset button ⑮ on the gamepad.

Disconnecting during the game.

Install the latest operating system updates on your device.
Press the reset button ⑮.
Wired connection. If you are using a USB hub, make sure it is connected to a power source. Connect the gamepad to a different USB connector.
Wireless connection. Make sure the gamepad is connected to the correct device.
Check the USB connection of the BT transmitter ⑭. Check if BT is turned on. Check the energy saving settings for BT and USB on the device the gamepad is connected to.
Inconsistency of the control buttons. Download updates from lorgar.eu. Switch your gamepad to Dinput mode. Press the reset button ⑮.

WARRANTY SERVICE

The warranty period begins on the date of purchase from an authorized Lorgar retailer.
To obtain warranty service, provide your device and proof of payment to the dealer. The warranty is 2 years, unless otherwise specified by local law. The service life is 2 years.
More information about use and warranty is available at lorgar.eu/warranty- terms.

FURTHER INFORMATION

Manufacturer: ASBISc Enterprises PLC, 1 Iapetou Street, Agios Athanasios, 4101 Limassol, Cyprus. Made in China.
The information is subject to change without notice to users. Up-to-date information and a detailed description of the gamepad, its connection and operation steps, certificates, and warranty conditions are available in the full user manual at lorgar.eu/drivers andmanuals. All trademarks and brand names are the property of their respective owners.

These symbols indicate that you must follow the Waste Electrical and Electronic Equipment (WEEE) and Waste Battery and Battery Regulations when disposing of the device, its batteries and accumulators, and its electrical and electronic accessories. According to the rules, this equipment must be disposed of separately at the end of its service life. Do not dispose of the device, its batteries and accumulators, or its electrical and electronic accessories together with unsorted municipal waste, as this will harm the environment. To dispose of this equipment, it must be returned to the point of sale or turned in to a local recycling facility. You should contact your local household waste disposal service for details.

LORGAR Logo