MARMITECK Buzz LO Smart WiFi Video Doorbell User Manual

MARMITECK Buzz LO Smart WiFi Video Doorbell User Manual

Buzz LO Smart Wi-Fi Video doorbell HD 1080p camera motion detection intercom

Bell ME Wireless Chime (Sold separately)

Package content

1 x Video doorbell                            1 x Screws (3 kinds)
1 x Bracket                                        1 x Screwdriver
1 x Angle Wall Mount                        1 x Reset pin
1 x Doorbell kit                                 1 x 3M
1 x Quick install guide

Marmitek Smart me app                 Multi language user guide

Set content

Video doorbell                     Doorbell kit Reset pin

3M double sided tape                        Angle wall mount Screws and wall plugs

Screwdriver                              User guide

Connections

Safety instructions

Please read these instructions thoroughly before you use the device and keep them for future reference.

•  This product is not a toy. Keep out of reach of children.
• Keep batteries out of the reach of children. Dispose of batteries as chemical waste. Never use old and new batteries or different types of batteries together. Remove the batteries when you are not using the system for a longer period of time. Check the polarity (+/-) of the batteries when inserting them in the product. Wrong positioning can cause an explosion.
• Never open the product: the device may contain parts with deadly voltage.
• Repairs or service should only be performed by qualified personnel.

Requirements

This product requires an 8 ~ 16 VAC 50 Hz power source and a stable internet connection (username/password).

Step 1a: Installation with your existing doorbell

1. Switch off the power supply to the existing doorbell and check whether it meets the required supply voltage.
2.  Remove the existing doorbell push button at the door, the Buzz LO will be connected to it later.
3.  Connect the supplied doorbell kit in parallel to the existing mechanical chime, no matter which wire is connected to the + or -. (You may need to temporarily remove the protective cover of your mechanical gong for this.)

Step 1b: Installation using a separate power supply

1. Switch off the power source and check whether it meets the required supply voltage.
2. Pull two wires to the location where you’d like to place the Buzz LO.
3. Connect the supplied doorbell kit in series to the power supply, but do not yet switch on the power supply. Warning: not connecting the doorbell kit can cause damage to the Buzz LO.
   Step 2: Mount the Buzz LO at its location Install the Buzz LO with or without using the supplied corner bracket. See page 16/18 for a detailed description.

Step 3: Install the Smart me app

1.  Download and install the Marmitek Smart me app on your smartphone or tablet.
2.  Launch the Smart me app after the installation is complete.
3.  Follow the instructions and register for a new account.

Step 4: Installation of the Buzz LO

1. Connect the Buzz LO to the 2 wires from step 1 and then switch on the power supply (of the existing doorbell or separate power supply).
2.  After starting up, the status light will blink rapidly and a tone will be heard. When the light does not blink, press the reset button with the supplied pin for 5-6 seconds.
3. Start the Smart me app on your smartphone or tablet.
4. Click on the + (top right corner) to add a new device. Click on the ‘Cameras’ category and select the Buzz LO. Check that the status light blinks red rapidly and follow the instructions on the display.
5. . Scan the QR code by holding the code 15-20 cm in front of the camera lens and confirm when you hear a beep from the camera. During installation, press the Help button for more information or if the installation
   fails.

Step 5 (optional): Installation of the Bell ME wireless chime

The Bell ME wireless chime is sold separately. It is possible to connect multiple wireless gongs to the Buzz LO video doorbell, for example, for use in different rooms

1.  Insert 3 AA batteries into the Bell ME, or power the Bell ME through the micro-USB.
2. Short press the button on the Bell ME to put it into pairing mode. A red light will flash to confirm.
3. Briefly press the button of the (already installed) Buzz LO once. A melody will be played to confirm.
4.  Now use the button to set the desired volume.
5. The button allows you to select a different melody.
   Follow the above steps again to connect an additional
   Bell ME wireless chime (sold separately).

Step 6: Setting the chime type

In the Buzz LO menu you can select which chime type you want to use. Open the Smart me app > select the Buzz LO > select settings (pen in top right) > select ‘Bell settings’

•  Existing doorbell – ON: notification via Smart me app,
• the existing doorbell and (if connected) via wireless doorbell (Bell ME).
• Existing doorbell – OFF: notification via Smart me app and (if connected) via wireless doorbell (Bell ME)

Notes regarding the use of the product

• Once the installation is complete, you can operate and configure the video doorbell using the app.
•  Please visit our website www.marmitek.com for more information and how to use the Smart me products.

Buzz LO

Video resolution                     1080p
Detection angle                      145°
Compression                          H.264
Bandwidth                              32 kbit/s ~ 2 Mbit/s
Night vision                           Infrared range up to 5 m
Audio                                     2-way communication
IP code                                  IP54 (water resistant)
SD card                                 Up to 128 GB, not included Wireless technology        Wi-Fi 2.4 GHz and RF 433

MHz

Power supply                         8 ~ 16 VAC 50/60 Hz, adapter not included
Standby consumption           < 0,5 Watt Operating temperature  -20° tot 50°C Dimensions       115 x 45 x 28 mm

Bell ME (available separately)

Wireless technology               RF 433 MHz
Maximum range                     Up to 80 m LOS (line of sight)
Volume level                          Adjustable in 4 steps
Power supply                          3x AA batteries (not included) or micro USB (cable not included)
Dimensions                           75 x 75 x 30 mm

Declaration of Conformity

Hereby, Marmitek BV, declares that the Buzz LO and Bell ME are in compliance with the essential requirements of the 2014/53/EU Directives. Full Declaration of Conformity is available at
www.marmitek.com/en/declarations-of-conformity/ More detailed user guide and instructions are available on our website at www.marmitek.com

Read More About This Manual & Download PDF:

References

• Marmitek | Specialist for 25 years | Wireless HDMI & audio and Smart Home
• Marmitek | Al 25 jaar specialist in slimme oplossingen
• Declarations of Conformity | Marmitek

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>