HANECO SOLO350W Solo LED Dimmer Lighting Installation Guide
- June 14, 2024
- HANECO
Table of Contents
HANECO SOLO350W Solo LED Dimmer Lighting
Product Information
- Technical Specifications
- Product Code: SOLO350W
- Max Dimmer Load and Multi Gang:
- 350W for 1 gang
- 300W for 2 gang
- 250W for 3 gang
- 200W for 4 gang
Product Usage Instructions
- Installation Guide
- Thank you for choosing our SOLO LED Dimmer product. Please follow these steps for installation:
- Step 1: Precaution
- Read the manual carefully before installation.
- Step 2: Wiring
- If a high load is experienced, connect the load correction device in parallel with the connected load of the SOLO dimmer to improve performance.
- Step 3: Connection Diagram
- Follow the one-way or two-way connection diagram provided in the manual based on your setup.
- Step 4: Mounting
- After wiring, install the dimmer onto the grid plate.
- Step 5: Knob Attachment
- Attach the rotary knob for control.
FAQs
- How can I make a warranty claim?
- Step 1: Contact Haneco if required.
- Step 2: Follow the instructions provided in the confirmation email from Haneco.
- Step 3: Upon complete documentation, you will be provided with a credit number or further instructions for resolution.
HANECO LED DIMMER INSTALLATION
- Thanks for choosing our SOLO LED Dimmer product.
- We strongly recommend that you read this manual carefully before installation.
- PRODUCT CODE: SOLO350W
WARNING
- This product must be installed by a licensed electrician following all the requirements of AS/NZS 3000 (current edition) and other relevant Standards and Regulations
- ENSURE electricity is disconnected before installation
- Indoor Use only. Not suitable for damp or explosive environments
- Complies to Australian Standards AS 60669.2.1 and AS CISPR 15 (x2 Capacitor IEC 60384-14)
- There are no serviceable parts inside
- Dimming circuits and product compatibility must be validated by the installer before installation. Haneco cannot be responsible for third-party changes in dimmer compatibility
- A load correction device – x2 Capacitor type 275Vac, 0.10µF, 40/110/56/B – has been included with your SOLO Dimmer.
- If flickering of the luminaire load is experienced, connect the load correction device in parallel with the connected load of the SOLOdimmer to improve performance
Technical Specifications
Connection Diagram
- ONE WAY CONNECTION
- TWO WAY CONNECTION
Contents
- After wiring, install it onto the grid plate.
- Attach the rotary knob.
- Compatibility – Dimming circuits and product compatibility must be validated by the installer before installation. Haneco cannot be responsible for third-party changes in dimmer compatibility.
- Ripple injection – In some regions of Australia a slight flicker may be experienced when a luminaire is dimmed. This is due to power line signals sent by electricity companies to assist with the switching of utilities. This effect is not a malfunction of the luminaire or dimmer but a result of local installation conditions changing during the day. If this occurs, adjusting the dimmer back to maximum brightness may help minimize flickering.
Warranty
- By Haneco Lighting’s standard terms and conditions of sale, Haneco Lighting warrants this product to be free from defects in materials and or workmanship for a period as stated below for goods not subject to incorrect installation, maintenance, operation, mishandling, environmental, unauthorised modifications or electrical operating conditions outside the nominated product specification as detailed in these installation instructions.
- The benefits to you given by this warranty are in addition to other rights and remedies you have under the law.
- Our goods come with guarantees that cannot be excluded under the Australian Consumer Law.
- You are entitled to a replacement or refund for a major failure and compensation for any other reasonably foreseeable loss or damage.
- You are also entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality and the failure does not amount to a major failure. Warranty term – 36 months from the date of purchase.
How to make a claim?
- Step 1
- Complete your online request at haneco.com.au/warranty (also available on mobile devices) or send us an email to warranty@haneco.com.au.
- Step 2 Ensure you provide the below documentation:
- RFC document with the reason for the request
- Photo(s) of the products including the batch number
- Original invoice number
- Make sure you send the purchase order for replacement products via EDI or orders@haneco.com.au if required.
- Step 3 Confirmation from Haneco:
- You will receive a confirmation email from Haneco, with a unique case number and should only respond to this original email to ensure your case is resolved promptly.
- If all documentation is sent and complete you will be provided with a credit number or instructions for the next step.
For more information
- www.haneco.com.au 1300 001 LED
- Last updated 14/03/24
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>