Remotec Technology Ltd Dimming Switch Module (Dual mode) ZDS-220NA Manual
- June 8, 2024
- Remotec Technology Ltd
Table of Contents
- Remotec
- Dimming Switch Module (Dual mode)
- SKU: ZDS-220NA
- Quickstart
- Important safety information
- What is Z-Wave?
- Product Description
- Prepare for Installation / Reset
- Inclusion/Exclusion
- Quick trouble shooting
- Association – one device controls an other device
- Configuration Parameters
- Technical Data
- Supported Command Classes
- Explanation of Z-Wave specific terms
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
Remotec
Dimming Switch Module (Dual mode)
SKU: ZDS-220NA
Quickstart
This is a
secure
Light Dimmer
for
U.S. / Canada / Mexico.
To run this device please connect it to your mains power supply.
Important safety information
Please read this manual carefully. Failure to follow the recommendations in
this manual may be dangerous or may violate the law.
The manufacturer, importer, distributor and seller shall not be liable for any
loss or damage resulting from failure to comply with the instructions in this
manual or any other material.
Use this equipment only for its intended purpose. Follow the disposal
instructions.
Do not dispose of electronic equipment or batteries in a fire or near open heat sources.
What is Z-Wave?
Z-Wave is the international wireless protocol for communication in the Smart
Home. This
device is suited for use in the region mentioned in the Quickstart section.
Z-Wave ensures a reliable communication by reconfirming every message ( two-
way
communication) and every mains powered node can act as a repeater for other
nodes
( meshed network ) in case the receiver is not in direct wireless range of
the
transmitter.
This device and every other certified Z-Wave device can be used together
with any other
certified Z-Wave device regardless of brand and origin as long as both are
suited for the
same frequency range.
If a device supports secure communication it will communicate with other
devices
secure as long as this device provides the same or a higher level of security.
Otherwise it will automatically turn into a lower level of security to
maintain
backward compatibility.
For more information about Z-Wave technology, devices, white papers etc.
please refer
to www.z-wave.info.
Product Description
ZDS-220 enabled product allows users to remotely control lighting, home appliance, and make home control easy with low installation and maintenance costs. You may begin with a few Z-Wave enabled devices as well as some of our products to build up a complete home automation system.The ZDS-220 is a Z-Wave enabled device and is fully compatible with any Z-Wave Plus enabled network. It can be configured as either a DIMMER or a SWITCH device. It allows remote Dimming or ON/OFF control of specified lamps. Each module is designed to act as a repeater, which will re-transmit a radio frequency (RF) signal by routing the signal around obstacles and radio dead spots to ensure that the signal is received at its intended destination.ZDS-220 is a security enabled Z-Wave plus device. A security Enabled Z-Wave Plus Controller must be used in order to fully utilize the product.
Prepare for Installation / Reset
Please read the user manual before installing the product.
In order to include (add) a Z-Wave device to a network it must be in factory
default
state. Please make sure to reset the device into factory default. You can do
this by
performing an Exclusion operation as described below in the manual. Every
Z-Wave
controller is able to perform this operation however it is recommended to use
the primary
controller of the previous network to make sure the very device is excluded
properly
from this network.
Safety Warning for Mains Powered Devices
ATTENTION: only authorized technicians under consideration of the country-
specific
installation guidelines/norms may do works with mains power. Prior to the
assembly of
the product, the voltage network has to be switched off and ensured against
re-switching.
Inclusion/Exclusion
On factory default the device does not belong to any Z-Wave network. The
device needs
to be added to an existing wireless network to communicate with the
devices of this network.
This process is called Inclusion.
Devices can also be removed from a network. This process is called
Exclusion.
Both processes are initiated by the primary controller of the Z-Wave network.
This
controller is turned into exclusion respective inclusion mode. Inclusion and
Exclusion is
then performed doing a special manual action right on the device.
Quick trouble shooting
Here are a few hints for network installation if things dont work as expected.
- Make sure a device is in factory reset state before including. In doubt exclude before include.
- If inclusion still fails, check if both devices use the same frequency.
- Remove all dead devices from associations. Otherwise you will see severe delays.
- Never use sleeping battery devices without a central controller.
- Dont poll FLIRS devices.
- Make sure to have enough mains powered device to benefit from the meshing
Association – one device controls an other device
Z-Wave devices control other Z-Wave devices. The relationship between one
device
controlling another device is called association. In order to control a
different
device, the controlling device needs to maintain a list of devices that will
receive
controlling commands. These lists are called association groups and they are
always
related to certain events (e.g. button pressed, sensor triggers, …). In case
the event happens all devices stored in the respective association group will
receive the same wireless command wireless command, typically a ‘Basic Set’
Command.
Association Groups:
Group NumberMaximum NodesDescription
1| 1| Association group_1 (max. 1 node) is default to associate with the
primary controller (Gateway/Hub/Controller) for ZDS-210 Status change report,
refer to below for report details:ZDS-210 will trigger AUTO report function if
the Dimmer or Switch status had been changed.Device Reset Locally
Notification(Only report when the ZDS-210 Dimming Switch Module has been
triggered the RESET TO DEFAULT)
---|---|---
2| 4| Dimmer mode: After receiving a dimming command from a local switch or
gateway (e.g. 50%), the ZDS-220 will automatically send out a related basic
set command (e.g. 50%) to its associated group. Switch mode: After receiving a
basic set command from a local switch or gateway, On (0xFF) or Off (0x00), the
ZDS-220 will automatically send out a related basic set command, On (0xFF) or
Off (0x00) to its associated group. (Max. 4 node ID’s can be assigned to this
association group)
Configuration Parameters
Z-Wave products are supposed to work out of the box after inclusion, however
certain configuration can adapt the function better to user needs or unlock
further
enhanced features.
IMPORTANT: Controllers may only allow configuring
signed values. In order to set values in the range 128 … 255 the value sent in
the application shall be the desired value minus 256. For example: To set a
parameter to 200 it may be needed to set a value of 200 minus 256 = minus
56.
In case of a two byte value the same logic applies: Values greater than 32768
may
needed to be given as negative values too.
Parameter 13: Double Click Option
Double Click option(set to max. brightness)0 (0x00) – Double click function
disabled1 (0x01) – Double click function enabled
Size: 1 Byte, Default Value: 1
SettingDescription
0 | Disable |
---|---|
1 | Enable |
Parameter 17: Time to move the Dimmer from 0% to max. dimming values
Time to move the Dimmer from 0% to max. dimming values.(The ZDS-220 will
implement the dimming duration if received this parameter value from
controller/gateway.Otherwise,the ZDS-220 will implement the local parameter
value)Dimmer Mode:From 0 to 5 secondsStep size = 1 second
Size: 1 Byte, Default Value: 3
SettingDescription
0 – 5 | Seconds |
---|
Parameter 18: Maximum Dimmer level control
Maximum Dimmer level control
Size: 1 Byte, Default Value: 99
SettingDescription
2 – 99 | Dimmer Level |
---|
Parameter 19: Minimum Dimmer level control
Minimum Dimmer level controlAC Motors:Parameter no. 18 max. = 99% Parameter
no. 19 min. >= 60%Fluorescent Lamps, Fluorescent Tubes, Non-dimmable LEDs:
Parameter no. 18 max. = 99% Parameter no. 19 min. = 98%Notes: 1) The maximum
level must not be lower than the minimum level. 2) Parameter no. 17 MUST be
set to 0]
Size: 1 Byte, Default Value: 13
SettingDescription
1 – 98 | Dimmer Level |
---|
Parameter 5: Switch returns to the last position saved before power
failure
Switch returns to the last position saved before power failure0 (0x00) –
Switch does not save the state after power failure, device returns to
u0022offu0022 position1 (0x01) – Switch saves its state before power failure
Size: 1 Byte, Default Value: 1
SettingDescription
0 | Not save |
---|---|
1 | Save |
Technical Data
Hardware Platform | ZM5202 |
---|---|
Device Type | Light Dimmer Switch |
Network Operation | Always On Slave |
Firmware Version | HW: 1 FW: 0.32 |
Z-Wave Version | 6.71.01 |
Certification ID | ZC10-19086723 |
Z-Wave Product Id | 0x5254.0x8200.0x8131 |
Color | White |
Electric Load Type | Dimmable LEDFluorescentIncandescent |
Firmware Updatable | Updatable by Consumer by RF |
Security V2 | S2_UNAUTHENTICATED |
Frequency | XXfrequency |
Maximum transmission power | XXantenna |
Supported Command Classes
- Association Grp Info V2
- Association V2
- Basic V2
- Configuration
- Device Reset Locally
- Firmware Update Md V4
- Manufacturer Specific V2
- Powerlevel
- Scene Activation
- Scene Actuator Conf
- Security
- Security 2
- Supervision
- Switch Multilevel V4
- Transport Service V2
- Version V2
- Zwaveplus Info V2
Explanation of Z-Wave specific terms
-
Controller — is a Z-Wave device with capabilities to manage the network.
Controllers are typically Gateways,Remote Controls or battery operated wall controllers. -
Slave — is a Z-Wave device without capabilities to manage the network.
Slaves can be sensors, actuators and even remote controls. -
Primary Controller — is the central organizer of the network. It must be
a controller. There can be only one primary controller in a Z-Wave network. -
Inclusion — is the process of adding new Z-Wave devices into a network.
-
Exclusion — is the process of removing Z-Wave devices from the network.
-
Association — is a control relationship between a controlling device and
a controlled device. -
Wakeup Notification — is a special wireless message issued by a Z-Wave
device to announces that is able to communicate. -
Node Information Frame — is a special wireless message issued by a
Z-Wave device to announce its capabilities and functions.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>