VITEK VTC-TNB8RMA4B Motorized IP Bullet Camera User Guide

VITEK VTC-TNB8RMA4B Motorized IP Bullet Camera

Product Information

• The Vitek VTC-TNB8RMA4 Transcendent Series 8 MegaPixel [4K] Gen. IV Advanced A.I. Motorized IP Bullet Camera is a high-quality surveillance camera designed for indoor or outdoor use. With advanced features like A.I. technology and motorized zoom, this camera is ideal for monitoring large areas with high precision.
• Please note that it is important to research local, state, and federal laws regarding the implementation of audio surveillance before using this camera.
• The camera comes with a hex wrench and anchors for installation, as well as a weather-resistant security cap and network coupler for protection against the elements.
• Complete user guides, software, tools, and updates are available online at http://www.vitekcctv.com/Downloads.

Product Usage Instructions

Step 1: Connect the Water Resistant Cap to an Ethernet patch cable, then connect the camera’s Ethernet adaptor. If not powering the camera with PoE, also connect the power cable to an approved 12VDC power supply.

Step 2: Connect the alarm input/output according to the provided diagram.

Step 3: To ensure weather resistance, follow the instructions for attaching the Weather Resistant Network Coupler.

Step 4: Before installation, ensure that the wall or ceiling is strong enough to withstand 3 times the weight of the camera. Use the provided drill template to drill 4 screw holes and 1 cable hole (if you want to route the cables through the mounting base). Route the cables and connect the power & video cables, use the rubber plug to fill the gap of the mounting base, then secure the mounting base to the ceiling or wall with screws.

Step 5: Loosen the mount lock to adjust the Pan and Tilt of the camera, then tighten the mount lock to secure the viewing angle adjustments.

Step 6: Open the cover of the camera and insert a MicroSD card. Re- install the cover evenly.

Step 7: To access the camera on the local network, use the IP-Tool installer available at
http://www.vitekcctv.com/Downloads/Software/Transcendent- IPTool_v2.0.2.zip. Modify the IP address and gateway of the camera to ensure it is in the same local network segment as the computer’s, and input the password of the administrator to modify the setting.

FEATURES

• 1/2.8” 8.0 Megapixel [4K] CMOS Image Sensor
• NDAA Compliant
• Up to 30fps live view @ 8 MegaPixel (3840×2160)
• 2.8~12mm Motorized Varifocal Lens
• Matrix IR (up to 230’ IR Range)
• True Wide Dynamic Range
• True Mechanical Day/Night function by ICR
• XD-DNR (3D & 2D-DNR) Noise Reduction
• Gen. IV Advanced Analytics: Abnormal Video, Face Detection, Regional Intrusion Detection, Regional Entrance / Exiting Detection, Line Crossing, Target Counting Detection
• Smart H.265 / H.265+ / H.265 / Smart H.264 / H.264+ / H.264 / MJPEG
• 1 Ch. Audio In + 1 Ch. Audio Out*
• 1 Ch. Alarm In + 1 Ch. Alarm Out
• CVBS Out
• Remote Viewing via CMS, Internet Explorer, iOS & Android Apps
• ONVIF Compliant
• MicroSD Card Slot for Local Recording (256GB)
• IP67 Weather Resistance
• Wall Mount Included, Optional Junction Box VT-TJB01 Available (see pg. 9 for additional mounting options)
• 12VDC & PoE (Power over Ethernet) Operation
• Please research local, state, and federal laws regarding the implementation of audio surveillance.

PLEASE NOTE:

• Complete User Guide, Software, Tools, and Updates are available online. Scan the QR Code or visit: http://www.vitekcctv.com/Downloads

Components and Accessories

Overview

1. Ethernet Connector
2. Audio Input (MIC)
3. Audio Output (HP)
4. CVBS Video Output
5. Alarm Input/Output
6. Power Connector
7. Micro SD card Slot
8. DC IN & CVBS Interface
9. Zoom –
10. Zoom + Reset

Network Cable & Power Connections
First, connect the Water Resistant Cap to an Ethernet patch cable, then connect the camera’s ethernet adaptor. If not powering the camera with PoE, also connect the power cable to an approved 12VDC power supply.

Connecting Alarm Input/Output Alarm Input

Weather Resistant Network Coupler

1. Loosen the nut from the Weather Resistant Network Coupler,
2. Run the ethernet cable through the coupler, then attach an RJ-45 connector.
3. Tighten the nut and coupler for a weather-resistant seal.

Installation

Before beginning installation, make sure that the wall or ceiling is strong enough to withstand 3 times the weight of the camera. The mounting steps are as follows:

1. Attach the drill template to the place where you want to install the camera, then drill 4 screw holes and 1 cable hole (if you want to route the cables through the mounting base) according to the drill template
2. Route the cables and connect the power & video cables, use the rubber plug to fill the gap of the mounting base. then secure the mounting base to the ceiling or wall with screws.
3. Loosen the mount lock to adjust the Pan and Tilt of the camera, then tighten the mount lock to secure the viewing angle adjustments.
4. 4. Open the cover of the camera as shown in the following figure, then insert a MicroSD card. Insert MicroSD
5. Re-install the cover back on the camera and close it with screws. Be sure to re-install the cover evenly.

LAN Configuration

The camera can be accessed on the local network either using the IP Tool or directly in a web browser.

Accessing the Camera Using the IP-Tool

1. Make sure the camera and PC are connected to the LAN.
2. Locate the IP-Tool installer at www.vitekcctv.com/Downloads/Soft-ware/Transcendent-IPTool_v2.0.2.zip, then install it on the PC. Open the installed application.
3. Modify the IP address. The default IP address is 192.168.226.201. Click the information on the camera listed in the above table to show the network information on the right side. Modify the IP address and gateway of the camera and make sure its network address is in the same local network segment as the computers. Please modify the IP address of your device according to the practical situation.
   • For example, the IP address of your computer is 192.168.13.4. So the IP address of the camera shall be changed to 192.168.13.X. After modification, please input the password of the administrator and click the “Modify” button to modify the setting.
   • Default admin password: “123456″.
4. Double-click the IP address and then the system will pop up the web browser to connect IP-CAM. IE browser will download the Active X control. After downloading, a login window will pop up as shown below:

• Input the user name and password to log in.
• Default user name: admin / Default password: 123456.

Directly Access Through a Web Browser

• The default network settings are as shown below:
• IP address: 192.168.226.201 HTTP: 80
• Subnet Mask: 255.255.255.0 Data Port: 9008
• Gateway: 192.168.226.1
• You may use the above default settings when you log in the camera for the first time.

1. Manually set the IP address of the PC. The network segment should be the same as the default settings of IP-CAM. Open the network and share center. Click “Local Area Connection” to pop up the following window.
   • Select “Properties” and then select Internet protocol according to the actual situation (for example: IPV4). Next, click “Properties” button to set the network of the PC.
2. Open the IE Browser and input the default address of IP-CAM and confirm. The IE browser will download Active X control.
3. After downloading Active X control, the login dialog box will pop up.
4. Input the default username and password and then enter to view.

WAN Configuration

Access the camera by the router or virtual server for example.

1. Make sure the camera is connected to the LAN; Then log into the camera via LAN and go to the System Congfig→Network Config→Port menu to set up the port number.
2. Enter the System Config→Network Config→IP Address menu to modify the IP address.
3. Go to the router’s management interface through the IE browser to forward the IP address and port of IP-CAM in the “Virtual Server”.
4. Open the web browser and input its WAN IP and HTTP port to access the IP-CAM.
5. For additional setup, features and functions, please scan the QR code on the front page of this quick guide and download the complete manual.

Please research local, state, and federal laws regarding the implementation of audio surveillance.

OPTIONAL ACCESSORIES AND RELATED PRODUCTS FOR VTC-TNB8RMA4

Transcendent

A Standalone Solution with Analytic Support and NDAA Compliance!

• 8MP (4K) HDMI Output
• H.265S / H.265+ / H.265 / H.264 Video Compression
• Analytic Support Including Basic Face Detection, License Plate Recognition, and More!
• Available in 4, 8, and 16 Channels
• Up to 24TB Depending on Model (12TB per HDD)
• PoE Support on ALL Models

Also, Consider Vitek NDAA Compliant Wireless

• Access Points to Reduce Costly Cable Installation!
• VT-WAP1150 and VT-WAP2150 High Speed 5.8GHz DIP AP / CPE Wireless Bridge w/ 8MB Storage, 64MB RAM, 150MBps transmission, and Point-to-Multi-Point (P2MP) Topology
• With the high-speed transmission of 150Mbps and a wireless range of 3000ft. (VT-WAP1150) and 1.25 miles (VT-WAP2150), these products eliminate the need for expensive and troublesome long-distance cables in areas where CCTV monitoring and rigorous surveillance take place. These small, lightweight, and durable units are easy to install and easy to use with an innovative and straightforward 10-button plug-and-play dip switch that facilitates the creation of a robust wireless network without a computer. Set-up can be simply configured for point-to-point or point-to-multipoint topology depending on the application, with up to 128 IP group configurations!

LIMITED PRODUCT WARRANTY

• VITEK products carry a three (3) year limited warranty. VITEK warrants to the purchaser that products manufactured by VITEK are free of any rightful claim of infringement or the like, and when used in the manner intended, will be free of defects in materials and workmanship for a period of three (3) years, or as otherwise stated above, from the date of purchase by the end user. This warranty is nontransferable and extends only to the original buyer or end user customer of a VITEK Authorized Reseller.
• The product must have been used only for its intended purpose, and not been subjected to damage by misuse, willful or accidental damage, caused by excessive voltage or lightning.
• The product must not have been tampered with in any way or the guarantee will be considered null and void.
• This guarantee does not affect your statutory rights.
• Contact your local VITEK Reseller should servicing become necessary.
• VITEK makes no warranty or guarantee whatsoever with respect to products sold or purchased through unauthorized sales channels. Warranty support is available only if product is purchased through a VITEK Authorized Reseller.
• 28492 CONSTELLATION ROAD VALENCIA, CA 91355WWW.VITEKCCTV.COM

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>