VITEK VTD-TND8RFA4-2 Transcendent Series Fixed IP Vandal Dome Camera User Guide

VITEK VTD-TND8RFA4-2 Transcendent Series Fixed IP Vandal Dome Camera

Product Information

The VTD-TND8RFA4-2 Transcendent Series 8 MegaPixel [4K] Gen. IV Advanced A.I. Fixed IP Vandal Dome Camera is a weather-resistant dome camera that provides high-quality video surveillance. It features an Ethernet connector, audio input connector, alarm input/output, power connector, reset button, and micro SD card slot. The camera also comes with a weather-resistant cap, drill template, rubber plug, and Allen key.

Features

• 8 Megapixel [4K] resolution
• Advanced A.I. technology
• Weather-resistant dome camera
• Ethernet connector
• Audio input connector
• Alarm input/output
• Power connector
• Reset button
• Micro SD card slot

Cable Connections

To connect the camera to the network, first connect the weather-resistant cap to an Ethernet patch cable, then connect the camera’s Ethernet adapter. If not powering the camera with PoE, also connect the power cable to an approved 12VDC power supply. The alarm input/output can be connected to a sensor or alarm using the provided cables.

Installation

Before beginning installation, make sure that the wall or ceiling is strong enough to withstand 3 times the weight of the camera.
Follow these steps to install the camera:

1. Attach the drill template to the place where you want to install the camera, then drill the screw holes and 1 cable hole according to the drill template.
2. If necessary, rotate the trim ring counterclockwise to remove it.
3. Loosen the screws to open the lower dome and then loosen the lock screw to remove the mounting base.
4. Route the cables and connect the power & video cables, use the rubber plug to fill the gap of the mounting base, then secure the mounting base to the ceiling or wall with screws.
5. Before adjusting the three-axis camera mount, preview the camera on a monitor, then adjust as necessary to achieve the optimum viewing angle.
6. Install the lower dome on the camera with the included screws, then put the trim ring back on the lower dome and rotate clockwise until it locks.

LAN Configuration

To access the camera on the local network, use the IP-Tool or directly in a web browser. Follow these steps to access the camera using the IP-Tool:

1. Make sure the camera and PC are connected to the LAN.
2. Locate the IP-Tool installer at www.vitekcctv.com/Downloads/Software/Transcendent-IPTool_v2.0.2.zip, then install on the PC. Open the installed application.
3. Modify the IP address. The default IP address is 192.168.226.201. Click the information of the camera listed in the above table to show the network information on the right side. Modify the IP address and gateway of the camera and make sure its network address is in the same local network segment as the computer’s.
   For more detailed instructions, please refer to the Complete User Guide, Software, Tools, and Updates available online at
   http://www.vitekcctv.com/Downloads.

FEATURES

• 1/2.8” 8.0 Megapixel [4K] CMOS Image Sensor
• NDAA Compliant
• Up to 30fps live view @ 8 MegaPixel (3840×2160)
• 2.8mm Fixed Iris Lens
• Matrix IR (up to 100’ IR Range)
• True Wide Dynamic Range
• True Mechanical Day/Night function by ICR
• XD-DNR (3D & 2D-DNR) Noise Reduction
• Gen. IV Advanced Analytics: Intrusion Detection, Line Crossing, Target Counting [All by Human / Motor Vehicle Classification], Face Detection, Video Blur, Video Color Cast Detection, Abnormal Video
• H.265+ / H.265 / H.264+ / H.264 / MJPEG
• 1 Ch. Audio In + Built-in Mic*
• 1 Ch. Alarm In + 1 Ch. Alarm Out
• ONVIF Compliant
• MicroSD Card Slot for Local Recording (256GB)
• IP67 Weather Resistance + IK10 Impact Rating
• Optional Junction Box (VT-TJB03A), Wall Mount (VT-TWMT3), Pendant / Ceiling Mount (VT-TPDM-1 [reqs. VT-TJB03A]) and In-Ceiling Semi Flush Mount (VT-TFMT-S) Available (see pg. 9 for additional mounting options)
• 12VDC & PoE (Power over Ethernet) Operation
• Available in Ivory or Charcoal Grey (VTD-TND8RFA4B-2)
  *Please research local, state and federal laws regarding the implementation of audio surveillance.

Components and Accessories

Overview

1. Ethernet connector
2. Audio input connector
3. Alarm input/output
4. Power connector
5. Reset
6. Micro SD Card Slot

Cable Connections

First connect the Weather Resistant Cap to an Ethernet patch cable, then connect the cameras ethernet adaptor. If not powering the camera with PoE, also connect the power Cable to an approved 12VDC Power Supply.

Connecting Alarm Input/Output

Weather Resistant Network Coupler

1. Loosen the nut from the Weather Resistant Network Coupler.
2. Run ethernet cable through coupler, then attach a RJ-45 connector.
3. Tighten the nut and coupler for a weather resistant seal.

Installation

Before beginning installation, make sure that the wall or ceiling is strong enough to withstand 3 times the weight of the camera. The mounting steps are as follows:

1. Attach the drill template to the place where you want to install the camera, then drill the screw holes and 1 cable hole according to the drill template.

2. Loosen the screws to open the lower dome and then loosen the lock screw to remove the mounting base.

3. Route the cables and connect the power & video cables, use the rubber plug to fill the gap of the mounting base, then secure the mounting base to the ceiling or wall with screws.

4. Before adjusting the three-axis camera mount, preview the  camera on a monitor, then adjust as necessary achieve the optimum viewing angle.

5. Install the lower dome on the camera with the included screws, then put the trim ring back on the lower dome and rotate clockwise until it locks

LAN Configuration

The camera can be accessed on the local network either using the IP-Tool or directly in a web browser

Accessing the Camera Using the IP-Tool

1. Make sure the camera and PC are connected to the LAN.
2. Locate the IP-Tool installer at www.vitekcctv.com/Downloads/Software/Transcendent-IPTool_v2.0.2.zip, then install on the PC. Open the installed application.

3. Modify the IP address. The default IP address is 192.168.226.201. Click the information of the camera listed in the above table to show the network information on the right side. Modify the IP address and gateway of the camera and make sure its network address is in the same local network segment as the computer’s. Please modify the IP address of your device according to the practical situation.
   For example, the IP address of your computer is 192.168.13.4. So the IP address of the camera shall be changed to 192.168.13.X. After modification, please input the password of the administrator and click “Modify” button to modify the setting.
   ** Default admin password: “123456″.

4. Double-click the IP address and then the system will pop up the web browser to connect IP-CAM . IE browser will download the Active X control. After downloading, a login window will pop up as shown below.

Input the user name and password to log in.
Default user name: admin / Default password: 123456

Directly Access Through a Web Browser
The default network settings are as shown below: IP address: 192.168.226.201 HTTP: 80 Subnet Mask: 255.255.255.0 Data Port: 9008 Gateway: 192.168.226.1 You may use the above default settings when you log in the camera for the first time.

1. Manually set the IP address of the PC. The network segment should be the same as the default settings of IP-CAM. Open the network and share center. Click “Local Area Connection” to pop up the following window
   Select “Properties” and then select Internet protocol according to the actual situation (for example: IPV4). Next, click “Properties” button to set the network of the PC.

2. Open the IE Browser and input the default address of IP-CAM and confirm. The IE browser will download Active X control.
3. After downloading Active X control, the login dialog box will pop up.
4. Input the default username and password and then enter to view.

WAN Configuration

Access the camera by the router or virtual server for example.

1. Make sure the camera is connected to the LAN; Then log into the camera via LAN and go to System Congfig→Network Config→Port menu to set up the port number.
2. Enter System Config→Network Config →IP Address menu to modify the IP address.

3. Go to the router’s management interface through IE browser to .forward the IP address and port of IP-CAM in the “Virtual Server

4. Open the web browser and input its WAN IP and HTTP port to  access the IP-CAM.
5. For additional setup, features and functions, please scan the QR code on the front page of this quick guide and  download the complete manual

SPECIFICATION

OPTIONAL ACCESSORIES AND RELATED PRODUCTS FOR VTD-TND8RFA4-2

NEWLY UPDATED Transcendent NVRs

PRODUCT FEATURES

• 8MP (4K) HDMI Output

• H.265S / H.265+ / H.265 / H.264 Video Compression

• Analytic Support Including Basic Face Detection,
  License Plate Recognition, and More!

• Available in 4, 8, and 16 Channels

• Up to 24TB Depending on Model (12TB per HDD)

• PoE Support on ALL Models

CONNECTION INSTRUCTION

• Also Consider Vitek NDAA Compliant Wireless Access Points to Reduce Costly Cable Installation!
• VT-WAP1150 and VT-WAP2150 High Speed 5.8GHz DIP AP / CPE Wireless Bridge w/ 8MB Storage, 64MB RAM, 150MBps transmission, and Point-to-Multi-Point (P2MP) Topology

• With high speed transmission of 150Mbps and a wireless range of 3000ft. (VT-WAP1150) and 1.25 miles (VT-WAP2150) these products eliminate the need for expensive and troublesome longdistance cables in areas where CCTV monitoring and rigorous surveillance take place. These small, lightweight and durable units are easy to install and easy to use with an innovative and straightforward 10-button plug-and-play dip switch that facilitates the creation of a robust wireless network without a computer. Set-up can be simply configured for point-to-point or point-to-multipoint topology depending on the application, with up to 128 IP group configurations!

LIMITED PRODUCT WARRANTY

• VITEK products carry a three (3) year limited warranty. VITEK warrants to the purchaser that products manufactured by VITEK are free of any rightful claim of infringement or the like, and when used in the manner intended, will be free of defects in materials and workmanship for a period of three (3) years, or as otherwise stated above, from the date of purchase by the end user. This warranty is nontransferable and extends only to the original buyer or end user customer of a VITEK Authorized Reseller.
• The product must have been used only for its intended purpose, and not been subjected to damage by misuse, willful or accidental damage, caused by excessive voltage or lightning.
• The product must not have been tampered with in any way or the guarantee will be considered null and void.
• This guarantee does not affect your statutory rights.
• Contact your local VITEK Reseller should servicing become necessary.
• VITEK makes no warranty or guarantee whatsoever with respect to products sold or purchased through unauthorized sales channels.
• Warranty support is available only if product is purchased through a VITEK Authorized Reseller.

ABOUT COMPANY

• 28492 CONSTELLATION ROAD VALENCIA, CA 91355
• WWW.VITEKCCTV.COM

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>