VITEK VTC-TNB4RMA4 4 Megapixel Network Outdoor IR Bullet Camera User Guide
- June 10, 2024
- VITEK
Table of Contents
VITEK VTC-TNB4RMA4 4 Megapixel Network Outdoor IR Bullet Camera
The VTC-TNB4RMA4 is a professional-grade IP bullet camera that provides advanced features for superior surveillance. It comes with a motorized lens and advanced A.I. technology that makes it ideal for use in surveillance systems that require high-quality imaging.
PRODUCT FEATURE
- 4 MegaPixel resolution
- Advanced A.I. technology
- Motorized lens
- Weather-resistant design
- Supports microSD card for local storage
- Easy LAN configuration
Components and Accessories
- Camera
- Rubber plug
- Allen Key
- Drill template
- Fixed Ring
- Mounting Base
- Network connector*
- Audio Input*
- Power connector*
- Micro SD card slot
- Reset button
- Sunshield
Please research local, state and federal laws regarding the implementation of
audio surveillance.
Please note that the complete user guide, software, tools, and updates are
available online. Scan the QR Code or visit:
http://www.vitekcctv.com/Downloads.
Installation
Before beginning installation, make sure that the wall or ceiling is strong enough to withstand 3 times the weight of the camera. The mounting steps are as follows:
- Attach the drill template to the place where you want toinstall the camera, then drill 3 screw holes and 1 cable hole (if routing the cables through the mounting base) according to the drill template
- Route the cables and connect the power & video cables, use the rubber plug to fill the gap of the mounting base, then secure the mounting base to the ceiling or wall with screws.
- Attach the weather-resistant cap to an ethernet patch cable. Connect the camera’s ethernet adapter. If not powering the camera with PoE, also connect the power cable to an approved 12VDC power supply.
- Loosen the nut from the weather-resistant network coupler, run ethernet cable through coupler, then attach an RJ-45 connector. Tighten the nut and coupler for a weather-resistant seal.
MicroSD Card Installation
To install a microSD card, remove the bottom of the cover from the camera, insert the card, and replace the cover (be sure it is even).
LAN Configuration
The camera can be accessed on the local network either using the IP-Tool or directly in a web browser.
Accessing the Camera Using the IP-Tool
-
Make sure the camera and PC are connected to the LAN.
-
Locate the IP-Tool installer at www.vitekcctv.com/Downloads/Software/Transcendent-IPTool_v2.0.2.zip,
then install on the PC. Open the installed application. -
Modify the IP address. The default IP address is 192.168.226.201. Click the information of the camera listed in the above table to show the network information on the right side. Modify the IP address and gateway of the camera and make sure its network address is in the same local network segment as the computer’s. Please modify the IP address of your device according to the practical situation.
- For example, if the IP address of your computer is 192.168.13.4, then change the IP address of the camera to 192.168.13.X. After modification, input the password of the administrator and click Modify button to modify the setting.
- The default admin password is 123456.
-
Double-click the IP address and then the system will pop up the web browser to connect IP-CAM. The IE browser will download the Active X control. After downloading, a login window will pop up as shown below:
The VTC-TNB4RMA4 is now ready for use in your surveillance system.
FEATURES
- 1/3” 4.0 Megapixel CMOS Image Sensor
- NDAA Compliant
- Up to 30fps live view @ 4 MegaPixel (2592×1520)
- 2.8~12mm Motorized Varifocal Lens
- Matrix IR (up to 165’ IR Range)
- True Wide Dynamic Range
- True Mechanical Day/Night function by ICR
- XD-DNR (3D & 2D-DNR) Noise Reduction
- Gen. IV Advanced Analytics: Regional Entrance / Exit Detection, Line Crossing, Target Counting [All by Human / Motor Vehicle Classification] Face Detection, Object Abandoned / Missing, Heat Map, Video Blur, Video Color Cast Detection, Abnormal Video
- H.265+/H.265/H.264+/H.264/MJPEG
- 1 Ch. Audio In*
- Remote Viewing via CMS, Internet Explorer, iOS & Android Apps
- ONVIF Compliant
- MicroSD Card Slot for Local Recording (256GB)
- IP67 Weather Resistance
- Wall Mount Included & Junction Boxes (VT-TJB08) Available (see pg. 9 for additional mounting options)
- 12VDC & PoE (Power over Ethernet) Operation
Please research local, state and federal laws regarding the implementation of audio surveillance.
PLEASE NOTE:
Complete User Guide, Software, Tools, and Updates are available online. Scan
the QR Code or visit: http://www.vitekcctv.com/Downloads
Components and Accessories
- Fixed Ring
- Mounting Base
- Network connector*
- Audio Input
- Power connector*
- Micro SD card slot
- Reset
- Sunshield
Connect the Weather Resistant Cap to an Ethernet patch cable. Connect the
cameras ethernet adaptor. If not powering the camera with PoE, also connect
the power Cable to an approved 12VDC Power supply
Weather Resistant Network Coupler
- Loosen the nut from the Weather Resistant Network Coupler,
- Run ethernet cable through coupler, then attach a RJ-45 connector.
- Tighten the nut and coupler for a weather resistant seal.
Installation
Before beginning installation, make sure that the wall or ceiling is strong
enough to withstand 3 times the weight of the camera. The mounting steps are
as follows:
MicroSD Card Installation: Remove the bottom of the cover from the camera,
insert card and replace the cover (be sure it is even).
- Attach the drill template to the place where you want to install the camera, then drill 3 screw holes and 1 cable hole (if routing the cables through the mounting base) according to the drill template
- Route the cables and connect the power & video cables, use the rubber plug to fill the gap of the mounting base, then secure the mounting base to the ceiling or wall with screws
- Loosen the mount lock to adjust the pan and tilt, then tighten the mount lock to secure the viewing angle adjustments.
- Carefully remove the protective film from the lens to complete the installation
LAN Configuration
The camera can be accessed on the local network either using the IP-Tool or directly in a web browser
Accessing the Camera Using the IP-Tool
-
Make sure the camera and PC are connected to the LAN.
-
Locate the IP-Tool installer at www.vitekcctv.com/Downloads/Software/
Transcendent-IPTool_v2.0.2.zip, then install on the PC. Open the installed application.
-
Modify the IP address. The default IP address is 192.168.226.201. Click the information of the camera listed in the above table to show the network information on the right side. Modify the IP address and gateway of the camera and make sure its network address is in the same local network segment as the computer’s. Please modify the IP address of your device according to the practical situation For example, the IP address of your computer is 192.168.13.4. So the IP address of the camera shall be changed to 192.168.13.X. After modification, please input the password of the administrator and click “Modify” button to modify the setting.
Default admin password: “123456″. -
Double-click the IP address and then the system will pop up the web browser to connect IP-CAM . IE browser will download the Active X control. After downloading, a login window will pop up as shown below:
Input the user name and password to log in. Default user name: admin / Default password: 123456.
Directly Access Through a Web Browser
The default network settings are as shown below:
- IP address: 192.168.226.201 HTTP: 80
- Subnet Mask: 255.255.255.0 Data Port: 9008
- Gateway: 192.168.226.1
You may use the above default settings when you log in the camera for the first time.
-
Manually set the IP address of the PC. The network segment should be the same as the default settings of IP-CAM. Open the network and share center. Click “Local Area Connection” to pop up the following window.
Select “Properties” and then select Internet protocol according to the actual situation (for example IPV4). Next, click the “Properties” button to set the network of the PC.
-
Open the IE Browser and input the default address of IP-CAM and confirm. The IE browser will download Active X control.
-
After downloading Active X control, the login dialog box will pop up.
-
Input the default username and password and then enter to view.
WAN Configuration
Access the camera by the router or virtual server for example.
- Make sure the camera is connected to the LAN; Then log into the camera via LAN and go to the System CongfigNetwork ConfigPort menu to set up the port number.
- Enter System ConfigNetwork Config>IP Address menu to modify the IP address.
- Go to the router’s management interface through IE browser to forward the IP address and port of IP-CAM in the “Virtual Server”.
- Open the web browser and input its WAN IP and HTTP port to access the IP-CAM
- For additional setup, features and functions, please scan the QR code on the front page of this quick guide and download the complete manual.
Please research local, state and federal laws regarding the implementation of audio surveillance.
OPTIONAL ACCESSORIES AND RELATED PRODUCTS FOR VTC-TNB4RMA4
VT-TJB08
Optional Junction Box
VT-TPLMT
Transcendent Universal Pole Mount (reqs. VT-TJB08)
VT-TCNMT
Transcendent Universal Corner Mount (reqs. VT-TJB08)
A Standalone Solution with Analytic Support and NDAA Compliance!
- 8MP (4K) HDMI Output
- H.265S / H.265+ / H.265 / H.264 Video Compression
- Analytic Support Including Basic Face Detection, License Plate Recognition, and More!
- Available in 4, 8, and 16 Channels
- Up to 24TB Depending on Model (12TB per HDD)
- PoE Support on ALL Models
Also, Consider Vitek NDAA Compliant Wireless Access Points to Reduce Costly
Cable Installation!
VT-WAP1150 and VT-WAP2150 High Speed 5.8GHz DIP AP / CPE Wireless Bridge w/
8MB Storage, 64MB RAM, 150MBps transmission, and Point-to-Multi-Point (P2MP)
Topology
With high speed transmission of 150Mbps and a wireless range of 3000ft. (VT-
WAP1150) and 1.25 miles (VT-WAP2150), these products eliminate the need for
expensive and troublesome longdistance cables in areas where CCTV monitoring
and rigorous surveillance take place. These small, lightweight and durable
units are easy to install and easy to use with an innovative and
straightforward 10-button plug-and-play dip switch that facilitates the
creation of a robust wireless network without a computer. Set-up can be simply
configured for point-to-point or point-to-multipoint topology depending on the
application, with up to 128 IP group configurations!
LIMITED PRODUCT WARRANTY
- VITEK products carry a three (3) year limited warranty. VITEK warrants to the purchaser that products manufactured by VITEK are free of any rightful claim of infringement or the like, and when used in the manner intended, will be free of defects in materials and workmanship for a period of three (3) years, or as otherwise stated above, from the date of purchase by the end user. This warranty is non-transferable and extends only to the original buyer or end-user customer of a VITEK Authorized Reseller.
- The product must have been used only for its intended purpose, and not been subjected to damage by misuse, willful or accidental damage, caused by excessive voltage or lightning.
- The product must not have been tampered with in any way or the guarantee will be considered null and void. This guarantee does not affect your statutory rights.
- Contact your local VITEK Reseller should servicing become necessary. VITEK makes no warranty or guarantees whatsoever with respect to products sold or purchased through unauthorized sales channels. Warranty support is available only if the product is purchased through a VITEK Authorized Reseller.
28492 CONSTELLATION ROAD VALENCIA, CA 91355
WWW.VITEKCCTV.COM
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>