MOEN BGCW10RV1618 Vessel Sink Bathroom Vanity Furniture and Cabinets Installation Guide
- June 10, 2024
- Moen
Table of Contents
INS12240B – 03/23
Installation Guide
Vessel
Sink
BGCW10RV1618
Image is for reference only
(Style varies by model)
Record Purchased Model Number:
(Save instruction sheet for future reference)
Register Online:
www.moen.com/product-registration
PLEASE CONTACT MOEN FIRST
For Installation Help, Missing or
Replacement Parts
(USA)
1-800-BUY-MOEN (1-800-289-6636)
WWW.MOEN.COM
(Canada)
1-800-465-6130
www.moen.ca
REQUIRED TOOLS
For safety and ease of sink replacement, see page 3 for required tools for
assembly.
Item List (Confi rm that all below items are inside the box)
A. Sink
B. Installation Guide
BEFORE YOU BEGIN
SAFETY INFORMATION
Please read and understand this entire manual before attempting to
assemble, operate or install the product.
CAUTION
Observe local plumbing and building codes.
PREPARATION
45 minutes
Tools Required for Assembly (not included): Faucet, drain, sealant and
adjustable wrench. If countertop cutout is required, you will also need a tape
measure, marking pencil, drill, drill bit and jigsaw.
Before beginning installation of product, make sure all parts are present.
Compare parts with items list on the previous page. If any part is missing or
damaged, do not attempt to assemble, install or operate the product.
Installing Your Product
Make sure there is enough space between the backsplash, faucet, fi xtures and
cabinets to install the new sink (A).
If making a cutout is necessary, trace
a 5-1/8″ (127mm) x 5-1/8″ (127mm) square and drill a clearance hole
approximately 1/4″ (6.4mm) to 1/2″ (12.7mm).
Following the perimeter line, cut the
opening for the sink (A) into the countertop.
Place your new sink (A) in desired
mounting position.
Check the fi t and alignment of the sink (A), making sure
to mark the sink’s location when the desired position has been found. Then
remove the sink and turn it upside down. Apply a generous amount of sealant
(not included) around the underside of the rim of the sink nearthe edge. Lower
sink in place, aligning with marks made earlier, and press down fi rmly.
Allow sealant to set before connecting supplies and drain (not
included).
Care and Maintenance
Clean with mild soap, warm water and a soft cloth. On tough stains, use a powdered detergent and a damp sponge or nylon scouring pad. Never use abrasive scouring powders, cleansers or pads because they will scratch, damage and dull the surface.
MOEN 5 YEAR LIMITED WARRANTY
Moen sinks have been manufactured under the highest standards of quality and
workmanship. Moen warrants to the original consumer purchaser the Moen sink
against defects in material and workmanship for a period of five (5) years
from date of purchase. Any defective sink or mounting fasteners will be
supplied FREE OF CHARGE for your replacement. We will not be responsible for
any product damage due to installation error, product abuse, or product
misuse, whether performed by a contractor, service company, or yourself.
Completion of the attached warranty card is not required in order to receive
warranty coverage. This warranty does not include incidentals such as labor
cost incurred for the installation of a replacement sink or consequential
damages. Some states do not allow the exclusion or limitations of incidental
or consequential damages, so the above limitation may not apply to you.
Moen Incorporated
25300 Al Moen Drive
North Olmsted, Ohio 44070-8022
U.S.A.
INS12240B – 03/23
©2023 Moen Incorporated
03/09/2023
INS12240B
500000562317
Released 00
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>