HALO FE08A40FDB LED Outdoor Entry Wall Lantern Sconce with Integrated Photocell Instruction Manual
- June 4, 2024
- HALO
Table of Contents
HALO FE08A40FDB LED Outdoor Entry Wall Lantern Sconce with Integrated
Photocell Instruction Manual
PACKAGING CONTENTS
A. Light fixture
B. Mounting bracket
C. (2) #6 and (2) #8 junction box screws (use the size that fits your junction box)
D. Screw
E. (3) Wire nuts
F. Photocell cap
ITEMS REQUIRED
(Purchase separately)
- Phillips screwdriver
- Weatherproof silicone caulk
IMPORTANT SAFETY INSTRUCTIONS
READ AND FOLLOW ALL SAFETY INSTRUCTIONS AND WARNINGS AND SAVE THESE INSTRUCTIONS:
- Heed all warnings, including below warnings AND those included on product.
- For outdoor use only.
- cULus LISTED for wet location.
- Your fixture is prewired and preassembled for easy installation.
WARNING
- Risk of fire/electric shock. If not qualified, consult an electrician.
- Disconnect power at fuse or circuit breaker before installing or servicing.
CAUTION
- Connect fixture to a 120 volt, 60 Hz power source. Any other connection voids the warranty
- Fixture should be installed by persons with experience in household wiring or by a qualified electrician. The electrical system, and the method of electrically connecting the fixture to it, must be in accordance with the National Electrical Code and local building codes.
- Fixture designed for wall mount to a recessed junction box only. Install fixture to junction box marked for use in wet locations.
NOTE: This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Under Part 15 of the FCC Rules, any changes or modifications to the fixture described in this instruction sheet that are not expressly approved by the manufacturer could void the user’s authority to operate the equipment.
FOR BEST RESULTS
- Install wall sconce 7-10 feet above the ground.
- Do not mount fixture close to reflective surfaces such as windows, white walls, white surfaces and water.
- When installing two fixtures on one switch, make sure the switch is rated for at least a 1A inductive load.
MOUNTING YOUR FIXTURE
NOTE: Do not mount within 2 feet of a highly reflective exterior inside corner (Fig. 1).
- Turn off the power at the main fuse/breaker box.
- Attach mounting bracket (B) to junction box with two screws (C) provided (Fig. 2).
WIRING YOUR FIXTURE
-
Connect the black fixture wire to the black supply wire (hot) using wire connector (E) (Fig. 3).
-
Connect the white fixture wire to the white supply wire (neutral) using wire connector (E) (Fig. 3).
-
Connect the copper ground fixture wire to an appropriate supply ground or a grounded junction box.
NOTE: Be careful to connect the wires correctly.
Make sure no bare strands of wire extend from the wire connector (E) provided or other approved wire connectors (not provided). -
Attach fixture to the J-Box by securing it with screw (D). (Fig. 4)
-
Add silicone caulk around fixture to help maintain a weather-resistant seal.
ADJUSTING THE LUMEN OUTPUT
- FE12 series of the product features Lumen selectable option. Choose between three preset Lumen outputs ( 700lm ,900lm and 1200lm) during or after installation. (Fig. 5)
- These Lumen settings can be selected using the Lumen button provided on the housing.
USING PHOTOCELL OPTION
Unscrew the Photocell Cap(F) to activate the photocell sensor (Fig 6)
TROUBLESHOOTING
| Problem | Cause | Solution |
|---|---|---|
| Light does not come on. | No power to the fixture | • Check if circuit breaker |
tripped. • Confirm wall switch is ON.
Fixture is sensing daylight.| • Cover photo control. Unit will switch on
immediately.
Wiring to the unit is loose.| TURN OFF POWER BEFORE CONTINUING.
• Confirm wiring is properly secured.
Light cycles on and off continuously| Light sensor is sensing reflected
light.| • Relocate light fixture where it no longer cycles on and off.
Light stays on.| Light sensor is in a shaded area.| • Shine a flashlight into
the light sensor. If the light turns off, the fixture is mounted in an area
that does not allow enough light to enter the light sensor.
Light sensor is faulty.| • Contact Customer Service
Fixture does not respond to motion. (FE10 Series only)| Motion Sensor field of
vision is blocked| Relocate the fixture where the sensor field of vision is no
longer blocked
Motion sensor is faulty.| Contact Customer Service.
5-YEAR LIMITED WARRANTY
THE FOLLOWING WARRANTY IS EXCLUSIVE AND IN LIEU OF ALL OTHER WARRANTIES,
WHETHER EXPRESS, IMPLIED OR STATUTORY INCLUDING, BUT NOT LIMITED TO, ANY
WARRANTY OF MERCHANTABILITY OR FITNESS FOR ANY PARTICULAR PURPOSE.
Cooper Lighting Solutions warrants to customers that, for a period of five
years from the date of purchase, Cooper Lighting Solutions products will be
free from defects in materials and workmanship. The obligation of Cooper
Lighting Solutions under this warranty is expressly limited to the provision
of replacement products. This warranty is extended only to the original
purchaser of the product. A purchaser’s receipt or other proof of date of
original purchase acceptable to Cooper Lighting Solutions is required before
warranty performance shall be rendered.This warranty does not apply to Cooper
Lighting Solutions products that have been altered or repaired, that have been
subjected to neglect, abuse, misuse or accident (including shipping damages).
This warranty does not apply to products not manufactured by Cooper Lighting
Solutions which have been supplied, installed, and/or used in conjunction with
Cooper Lighting Solutions products. Damage to the product caused by
replacement bulbs or corrosion or discoloration of brass components are not
covered by this warranty. LIMITATION OF LIABILITY: IN NO EVENT SHALL COOPER
LIGHTING SOLUTIONS BE LIABLE FOR SPECIAL, INDIRECT, INCIDENTAL, OR
CONSEQUENTIAL DAMAGES (REGARDLESS OF THE FORM OF ACTION, WHETHER IN CONTRACT,
STRICT LIABILITY, OR IN TORT INCLUDING NEGLIGENCE), NOR FOR LOST PROFITS; NOR
SHALL THE LIABILITY OF COOPER LIGHTING SOLUTIONS FOR ANY CLAIMS OR DAMAGE
ARISING OUT OF OR CONNECTED WITH THESE TERMS OR THE MANUFACTURE, SALE,
DELIVERY, USE, MAINTENANCE, REPAIR OR MODIFICATION OF COOPER LIGHTING
PRODUCTS, OR SUPPLY OF ANY REPLACEMENT PARTS THEREFORE, EXCEED THE PURCHASE
PRICE OF COOPER LIGHTING SOLUTIONS PRODUCTS GIVING RISE TO A CLAIM. NO LABOR
CHARGES WILL BE ACCEPTED TO REMOVE OR INSTALL FIXTURES.
To obtain warranty service, please contact Cooper Lighting Solutions at 1-800-334-6871, press option 2 for Customer Service, or via e-mail ConsumerProducts@Cooperlighting.com and include the following information:
- Name, address and telephone number
- Date and place of purchase
- Catalog and quantity purchase
- Detailed description of problem
All returned products must be accompanied by a Return Goods Authorization
Number issued by the Company and must be returned freight prepaid. Any product
received without a Return Goods Authorization Number from the Company will be
refused. Cooper Lighting Solutions is not responsible for merchandise damaged
in transit. Repaired or replaced products shall be subject to the terms of
this warranty and are inspected when packed. Evident or concealed damage that
is made in transit should be reported at once to the carrier making the
delivery and a claim filed with them.
Reproductions of this document without prior written approval of Cooper
Lighting Solutions are strictly prohibited.
For assistance, call 1-800-334-6871 or
e-mail us at
ConsumerProducts@Cooperlighting.com
Printed in China
1121 Highway 74 South, Peachtree City, GA 30269
www.CooperLighting.com
© 2022 Cooper Lighting Solutions
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>