peerless-AV SR598-HUB2 SmartMount Flat Panel Cart Instruction Manual
- June 10, 2024
- Peerless-AV
Table of Contents
peerless-AV SR598-HUB2 SmartMount Flat Panel Cart
Product Information
- Model: SR598-HUB2
- Maximum Weight Capacity: 300 lb (136 kg)
- Height: 85 in (215 cm)
- Manufacturer Date: 2021-11-15
- Manual #: 009-9159-1
The SR598-HUB2 is a product designed for lifting and positioning equipment. It has a maximum weight capacity of 300 lb (136 kg) and a height of 85 in (215 cm). The product should only be used by following the instructions and warnings provided in the user manual.
Product Usage Instructions
- Read and understand all instructions and warnings provided in the user manual before beginning to install the product.
- Always use an assistant or mechanical lifting equipment to lift and position the equipment being used with the product.
- Ensure that all screws are firmly tightened, but not overtightened, by turning them until they make contact and then tightening another half turn.
- Do not attempt to repair or service any parts of the mounting system, as there are no user-serviceable parts.
- Use caution when operating the product to prevent finger pinching or other injuries.
- Do not exceed the maximum weight capacity of the product.
Refer to the parts list included in the user manual for information on specific parts and quantities.
WARNING
- Do not begin to install the product until you have read and understood the instructions and warnings contained in this user guide.
- Always use an assistant or mechanical lifting equipment to safely lift and position equipment.
- This product must be installed onto flat, hard, level surface to prevent tipping.
- Use with heavier displays may result in instability causing tip over resulting in death or serious injury.
- The cart or stand is not affixed or secured to the floor, and may therefore tip over and/or fall if screen and/or stand is shaken or hit.
- This product is intended for indoor use only.
- Use of this product outdoors could lead to product failure or personal injury. Screws must be tightly secured.
- Do not overtighten screws or damage can occur and the product may fail.
- Never exceed the Maximum Load Capacity.
- Be careful not to pinch your fingers when operating the mount.
- Death or serious injury may occur when children climb on audio and/or video equipment furniture.
- A remote control or toys placed on the furnishing may encourage a child to climb on the furnishing and as a result the furnishing may tip over on to the child.
- Relocating audio and/or video equipment to furniture not specifically designed to support audio and/or video equipment may result in death or serious injury due to the furnishing collapsing or overturning onto a child. For support please call customer care at 1-800-865-2112.
Symbols
- WARNING
- Skip to step.
- Screws must get at least three full turns and fit snug.
- Do not overtighten screws.
Tools Needed for Assembly
The mounting system has no user-serviceable parts.
To properly tighten screws: Tighten until the screw head makes contact, then
tighten another 1/2 turn. Do not overtighten screws.
Parts List
Parts (Before beginning, make sure you have all parts shown below).
| Parts List | SR598-HUB2 Part # | |
|---|---|---|
| Description | Qty | |
| A | base | 1 |
| B | caster (non locking) | 2 |
| C | caster (locking) | 2 |
| D | vertical column | 2 |
| E | 3/8″-16 x 1.5″ long bolts | 8 |
| F | split washer | 8 |
| G | bracket | 2 |
| H | 5/16-18 socket screw | 8 |
| I | nut bar | 4 |
| J | M6/M8 washer | 12 |
| K | retaining washer | 8 |
| L | adjustment bracket | 2 |
| M | knob | 2 |
| N | column cover | 2 |
| O | horizontal display adaptor | 1 |
| P | vertical adaptor bracket | 2 |
| Q | M6 x 12mm socket pin screw (not used) | 4 |
| R | M6 x 25mm socket pin screw (not used) | 4 |
| S | M8 x 12mm socket pin screw (not used) | 4 |
| T | M8 x 25mm socket pin screw (not used) | 4 |
| U | washer (not used) | 8 |
| V | .25″ height spacer (not used) | 8 |
| W | 3/16″ allen wrench | 1 |
| X | 7/32″ allen wrench | 1 |
| Y | 4mm allen wrench | 1 |
| Z | 7/32″ hex power bit | 1 |
| AA | base foot | 4 |
| BB | M5 x 13mm self-tapping | 8 |
| CC | 4mm security driver | 1 |
| DD | M8 x 16mm | 8 |
| EE | 5mm allen wrench (not used) | 1 |
| FF | M8 x 50mm (not used) | 4 |
| GG | 10mm spacer | 4 |
| HH | M8 x 65mm screw | 4 |
| II | M8 lock washer | 4 |
| JJ | 6mm allen wrench | 1 |
INSTALLATION
Hand tighten
Lock wheels.
Do not tighten.
Top view.
- Tighten, minimum 30 in. • lb (3 N.M.).
Height adjustment.
- Tighten, minimum 30 in. • lb (3 N.M.).
- To prevent damage or injury, never adjust with display attached.
Tighten.
Tilt adjustment.
- Tighten, minimum 30 in. • lb (3 N.M.).
- To prevent damage or injury, do not loosen top screw.
Center adaptor brackets vertically on back of screen.
Cable management.
Warranty
Peerless-AV
2300 White Oak Circle
Aurora, IL 60502
Email: tech@peerlessmounts.com
Ph: 800-865-2112
Fax: 800-359-6500
www.peerless-av.com
© 2021, Peerless Industries, Inc.
Peerless-AV Europe
Unit 3 Watford Interchange,
Colonial Way, Watford, Herts,
WD24 4WP, United Kingdom
Customer Care
44 (0) 1923 200 100
www.peerless-av.com
© 2021, Peerless Industries, Inc.
Peerless-AV América Latina
Av. de las Industrias 413
Parque Industrial Escobedo
General Escobedo N.L., México 66062
Servicio al Cliente
01-800-849-65-77
www.peerless-av.com
© 2021, Peerless Industries, Inc.
© 2021 Microsoft. Microsoft, the Microsoft logo, Microsoft Surface, Surface,
and the Microsoft Surface logo are trademarks of the Microsoft group of
companies. All other trademarks are the property of their respective owners.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>