peerless-AV DS-LEDUNV610-4X4 Seamless Kitted Universal Installation Guide
- June 1, 2024
- Peerless-AV
Table of Contents
peerless-AV DS-LEDUNV610-4X4 Seamless Kitted Universal
Specifications
- Product Name: SEAMLESS Kitted Universal Series
- Model Number: 146-9082-2
- Date: 2024-03-04
Product Information
The SEAMLESS Kitted Universal Series is a versatile mounting solution designed
for a variety of display models. The kit includes a latch assembly, horizontal
extrusion, wall plate, depth adjustment bracket, connector plate, and various
screws and washers for assembly.
Parts List
- A latch assembly
- 4′ horizontal extrusion
- Wall plate
- Depth adjustment bracket
- Connector plate
- Various screws and washers
Tools Needed for Assembly
- 5/32 (4mm) Allen wrench
- 3/8 (10mm) wrench
- 5mm, 6mm, 8mm wrenches
Step 1: Parts Check
Before starting the assembly, ensure you have all the parts listed in the
parts list included with your model.
Step 2: Screw Tightening
To properly tighten screws, follow these steps:
- Tighten until screw head makes contact with the surface.
- Then tighten another 1/2 turn.
- Do not overtighten screws.
WARNING
This product is designed to be installed on plywood walls. Hardware is
included for plywood installation. This product is designed to be installed on
flat, unobstructed, vertical walls. Do not install on curved or angled
walls. Before installing make sure the supporting surface will support the
combined load of the equipment and hardware. Screws must be tightly secured.
Do not overtighten screws or damage can occur and product may fail. Never
exceed the Maximum Load Capacity. Always use an assistant or mechanical
lifting equipment to safely lift and position equipment. This product is
intended for indoor use only. Use of this product outdoors could lead to
product failure or personal injury. Be careful not to pinch fingers when
operating the mount. For support please call customer care at
1-800-865-2112.
Tools Needed for Assembly.
Parts (Before beginning, make sure you have all parts shown below). *Refer to
parts list included with your model. 
Parts List
| Description| Qty.
N| spacer| 2
O| 3mm allen wrench| 1
P| wall plate shim| 10
Q| 4mm allen wrench| 1
R| spacer extension| 2
S| M5 flat head screw| 8
T| 1/4″ flat washer| 8
See the table and drawing below for the dimensions that will locate the mount on the wall.
Compa�ble Display
| Bo�om of the video wall to the
top of the first wall plate.
Dimension A
| Side of video wall to
center of first wall plate Dimension B
| Center to center
wall plates. Dimension C
| System Depth Range.
Dimension D
---|---|---|---|---
Absen Acclaim Plus/Pro/V3| 345.24| 305| 610| 120.65-137.67
Absen KL II| 395.74| 320| 640| 136.40-153.67
Absen NX| 582.74| 240| 480| 115.06-132.08
AOTO CVE| 360.25| 300| 600| 108.71-125.98
Barco XT| 382.17| 305| 610| 142.75-159.76
Chris�e CSII| 368.24| 300| 600| 108.71-125.98
Chris�e CSIII| 368.24| 300| 600| 100.58-117.86
Fabulux T Series| 515.24| 250| 500| 103.88-121.16
INFiLED WP| 365.49| 300| 600| 101.34-118.36
INFiLED WT| 365.49| 300| 600| 101.34-118.36
Jupiter ZavusXP0.7| 290.73| 240| 480| 99.57-116.58
Jupiter ZavusXP0.9-1.2| 348.23| 300| 600| 99.57-116.58
Just Video Walls| 361.9| 300| 600| 110.74-127.76
Leyard GF| 504.74| 320| 640| 145.54-162.56
LG LSAC| 700.68| 300| 600| 122.68-139.70
LG LSBB| 384.45| 300| 600| 127.25-144.27
LG LSBE| 380.37| 300| 600| 143.51-160.53
LG LSBF| 715.72| 300| 600| 143.51-160.53
LG LSCA-GK2 (500×500)| 532.79| 250| 500| 136.65-153.67
LG LSCA-GK (500×1000)| 1032.79| 250| 500| 136.65-153.67
LG LSCB| 365.49| 300| 600| 101.09-118.11
Linsn MA640| 505.74| 320| 640| 128.52-145.79
Linsn N169S| 382.74| 300| 600| 117.60-134.87
MAXHUB M27| 378.87| 320| 640| 102.61-119.63
Philips 27BDL6000| 382.74| 304| 608| 130.55-147.57
Philips 28HDL5000| 538.69| 250| 500| 113.54-130.81
Philips 44HDL5000| 1038.69| 250| 500| 113.54-130.81
Planar 27″ DLP| 380.94| 302.4| 604.8| 116.58-133.86
Planar 36″ DLP| 721.14| 302.4| 604.8| 116.58-133.86
QST PH| 365.49| 300| 600| 108.20-125.47
Samsung IEC| 373.24| 300| 600| 109.73-127
Sharp NEC E Series| 379.49| 300| 600| 100.58-117.60
Sharp NEC FA, FC, FE| 378.74| 304| 608| 120.65-137.67
SNA VST| 480.74| 200| 400| 117.60-134.62
SNA VTII| 475.74| 200| 400| 144.78-162.05
Sony BC| 377.74| 304| 608| 120.14-137.16
Sony BHCH| 345.24| 305| 610| 140.21-157.22
Unilumin ULWIII| 378.24| 300| 600| 116.33-133.35
Unilumin Umini III| 378.24| 300| 600| 112.01-129.28
Unilumin Upanel II| 383.82| 305| 610| 139.70-156.72
Unilumin UPanelS| 381.53| 305| 610| 142.75-159.77
Unilumin UPanelSII| 383.82| 305| 610| 136.65-153.92
Unilumin Uslim II (500×250)| 290.69| 250| 500| 110.23-127.51
Unilumin Uslim II (500×500)| 499.9| 250| 500| 110.23-127.51
Unilumin Uslim II (500×1000)| 1040.74| 250| 500| 110.23-127.51
Unilumin UTWIII| 580.79| 240| 480| 99.82-116.84
-
Optional: connecting two horizontal extrusions.
-
Determine the required extrusion length with the following extrusion cut to length formula:
Video Wall Width – 0.25″ (6mm) = Extrusion Length
-
Now that the extrusions are cut to length, separate the extrusions and slide wall plates onto horizontal extrusions and tighten with the wall plate fully extended (one wall plate per display unless the display is >960mm wide, in which case there will be two wall plates per display).
WARNIN G
When installing Peerless wall mounts on a wood stud wall covered with plywood,
verify that the wood studs are a minimum of 2″ x 4″ nominal size and plywood
is a minimum Grade BC, 1/2″ (13mm) thick. Plywood may be covered by gypsum
board (drywall) up to 5/8″ thick.
Install the bottom row, first extrusion assembly, on the laser line per table
(step 1), dimension “A”. Install additional bottom row extrusions one at a
time using connector plates to join extrusions. Drill mounting holes and
install screws and washers with top edge of the wall plates on the laser line.
- Determine the height of the display being mounted and locate the same dimension on the front of the spacer. If the display height is above 540mm, add the spacer extension. If display height is not listed on the spacer, measure the display to set custom spacing.
Add the extension for displays taller than 540mm. Move the spacer bracket and clamp to the lower extension.
- Move spacer bracket and clamp to the desired display height. This may require adjusting the pins of spacer bracket.
- Optional: Remove and replace pins to align with correct display height.
- If the display height is not listed on the spacer, measure the display to set the spacing.
- Install remaining extrusions using the spacers. Clamp the upper spacer jaw assembly to an uninstalled extrusion assembly. Clamp the bottom spacer jaw assembly to the installed extrusion. Vertically align extrusions with a laser. Drill mounting holes into supporting surface and install wall plates to the wall.
- Loosen clamps and remove spacers.
- Repeat steps above to install the next extrusion.
- Engage and secure connecter plate to mounted extrusions. Secure wall plates to wall. Remove spacer when extrusions are fully secured.
- Set a laser level so that it is parallel to the mounting surface (wall). Measure to the face of the extrusion so that all points of the extrusion are the same distance from the laser line, creating one flat plane across the face of the mount. Tighten screws.
- Double check using a straight edge to span three extrusions. Adjust low and high spots as needed.
- Hook display cabinets onto horizontal extrusion, adjust height to level and join cabinets together using connecting system. Adjust plumb, close latch, then run cables one at a time starting from left to right.
- Hook display cabinets onto horizontal extrusion, adjust height to level and join cabinets together using connecting system. Close latch, then run cables one at a time starting from left to right.
- To remove, start from the top right. Open latch assemblies, disconnect cables, separate cabinets and remove displays one at a time.
www.peerless-av.com/warranty • www .peerless-av.com • www.peerless- av.com/patents
- Peerless-AV
- 2300 White Oak Circle
- Aurora, IL 60502, USA
info@peerless-av.com
800-865-2112
630-375-5100
© 2024 Peerless Industries, Inc. Peerless-AV® is a registered trademark of Peerless Industries, Inc. All rights reserved. Other parties’ marks are the property of their respective owners.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>