peerless-AV SF680P-HUB2 Flat TV Wall Mount Installation Guide
- June 10, 2024
- Peerless-AV
Table of Contents
SF680P-HUB2 Flat TV Wall Mount
Installation Guide
SF680P-HUB2 Flat TV Wall Mount
| 85″ (215 cm)| | 350 lb (159 kg)
---|---|---|---
WARNING
This product is designed to be installed on wood stud, solid concrete or
cinder block walls. Hardware is included for wood stud, solid concrete and
cinder block installation. Before installing make sure the supporting surface
will support the combined load of the equipment and hardware. Screws must be
tightly secured. Do not overtighten screws or damage can occur and product may
fail. Never exceed the Maximum Load Capacity. Always use an assistant or
mechanical lifting equipment to safely lift and position equipment. This
product is intended for indoor use only. Use of this product outdoors could
lead to product failure or personal injury. Be careful not to pinch fingers
when operating the mount. For support please call customer care at
1-800-865-2112.
Symbols
| WARNING
---|---
| Do not overtighten screws.
| Listen
| Skip to step.
| Display center.
| Screws must get at least three full turns and fit snug.
Tools Needed for Assembly
To properly tighten screws: Tighten
until screw head makes contact, then tighten another 1/2 turn. Do not
overtighten screws.
Parts
(Before beginning, make sure you have all parts shown below).
Parts List
Description| Qty| SF680P-HUB2
Part #
---|---|---
A wall plate| 1| 096-SG1588
B adaptor bracket| 2| 096-SG1582
C 4mm allen wrench| 1| 560-1145
D 8mm concrete anchor| 6| 590-0320
E #14 x 2.5″ wood screw| 6| 5S1-015-C03
F M6 x 12mm (not used)| 4| 520-1128
G M6 x 25mm (not used)| 4| 520-1208
H M8 x 12mm (not used)| 4| 520-9571
I M8 x 25mm (not used)| 4| 520-1031
J M6/M8 washer (not used)| 8| 540-9406
K .25″ height spacer (not used)| 8| 600-1215
L M10 x 15mm (not used)| 4| 520-1305
M M8 x 50mm (not used)| 4| 521-1009
N 10mm spacer| 4| 10004495
O M8 x 65mm screw| 4| 10004807
P M8 lock washer| 4| 10004497
Q 6mm allen wrench| 1| 560-9716
Wood stud wall.
Concrete/Cinder block.
1a.
WARNING
When installing Peerless wall mounts on a wood stud wall covered with gypsum
board (drywall), verify that the wood studs are a minimum of 2″ x 4″ nominal
size. Do not install over gypsum board thicker than 5/8″.
Use stud finder to locate and mark stud center lines.
Level wall plate. Mark mounting holes
on stud center lines. Wall plate must be centered on middle stud as shown.
Drill mounting holes into
supporting surface (2.5″ (64mm) minimum depth required).
Mounting hole must center on stud.
Level
wallplate. Mark mounting holes on stud center lines. Wallplate must be
centered on middle stud as shown.
Drill mounting holes into
supporting surface (2.5″ (64mm) minimum depth required).
Mounting hole must center on stud.
Level wallplate. Install using wood
screws provided.
Maximum 80 in. • lb (9 N.M.).
1b.
WARNING
When installing Peerless wall mounts on a concrete wall, the wall must be at
least 8″ thick with a minimum compressive strength of 2000 psi. When
installing Peerless wall mounts on a cinder block wall, the cinder blocks must
meet ASTM C-90 specifications and have a minimum nominal width of 8″. Do not
drill into mortar joints! Be sure to mount in a solid part of the block,
generally 1″ (25 mm) minimum from the side of the block. It is suggested that
a standard electric drill on slow setting is used to drill the hole instead of
a hammer drill to avoid breaking out the back of the hole when entering a void
or cavity. Never attach concrete expansion anchors to concrete or cinder block
covered with plaster, drywall or other finishing material.
Level wallplate. Mark mounting holes.
Drill mounting holes into supporting surface (2.5″ (64mm) minimum
depth required).
Do not drill into mortar joints.
Insert anchor flush to concrete.
Level wallplate. Install using concrete
anchors and wood screws provided.
Maximum 80 in. • lb (9 N.M.).
2. Center adaptor brackets vertically on back of screen.
Height adjustment: Tighten or loosen.
7.
WARNING
Do not bump screen while adapter brackets are disengaged, or screen may fall.
Kickstand is for maintenance only.
Optional: Cable management.
Re-engage the display.
Optional: Remove display.
Caution: If removing quick-release
string, allen wrench required to remove display.
Optional
Warranty
Peerless-AV
2300 White Oak Circle
Aurora, IL 60502
Email: tech@peerlessmounts.com
Ph: 800-865-2112
Fax: 800-359-6500
www.peerless-av.com
© 2021, Peerless Industries, Inc.| Peerless-AV Europe
Unit 3 Watford Interchange,
Colonial Way, Watford, Herts,
WD24 4WP, United Kingdom
Customer Care
44 (0) 1923 200 100
www.peerless-av.com
© 2021, Peerless Industries, Inc.| Peerless-AV América Latina
Av. de las Industrias 413
Parque Industrial Escobedo
General Escobedo N.L., México 66062
Servicio al Cliente
01-800-849-65-77
www.peerless-av.com
© 2021, Peerless Industries, Inc.
© 2021 Microsoft. Microsoft, the Microsoft logo, Microsoft Surface, Surface, and the Microsoft Surface logo are trademarks of the Microsoft group of companies. All other trademarks are the property of their respective owners.
2021-11-15 #:204-9131-1
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>