WALI SWM202 Speaker Wall Mounts Instruction Manual

WALI SWM202 Speaker Wall Mounts

Product Information: Speaker Wall Mount

The Speaker Wall Mount comes in three models: SWM202, SWM402, and SWM602. Each model is available in white (SWM202-W, SWM402-W, and SWM602-W) and has a maximum weight capacity of the equipment and all attached hardware and components. The product is manufactured by Walielectric and comes with a metal wall plate, bolts, and screws for mounting.

Product Usage Instructions

1. Ensure that the supporting surface can safely support the combined load of the equipment and all attached hardware and . Use a stud finder to locate the edges of the studs.

2. Option A: Wood Stud Mounting

3. Mark the center of the two mounting holes on the wall plate. Make sure that the mounting holes are on the stud centerline.

4. Drill two 1/8 (3mm) dia. Holes 1 (25mm) deep. Attach the wall plate to the wall using two screws (part – E). Make sure that the wall plate is level.

5. Option B: Sold Brick and Concrete Wall Mounting

6. Use the metal wall plate as a template to mark two holes on the wall as shown in the figure.

7. Drill two 7/32 (5.5mm) dia. Holes 1.2 (30mm) deep. Insert a
   Concrete Anchor (Part- F ) into each of these holes. Attach the wall plate to the wall using two screws (Part- E), make sure that the wall plate is level.

8. Hand thread bolts into the threaded inserts on the back of your Speaker to determine which bolt to use. Attach Speaker to top bracket using Bolts B C D.

9. Assemble the Speaker with the top bracket onto the bracket set and wall plate securely.

10. Adjust the angle of the speaker as needed.

Speaker Wall Mount
SWM202 / SWM402 / SWM602 SWM202-W / SWM402-W/ SWM602-W

www.walielectric.com
support@walielectric.com
1-844-SATTLER (18447288537) WARNING!
If you do not understand these directions, or if you have any doubts about the safety of the installation, please call a qualified technician. Check carefully to make sure there are no missing or defective parts. Improper installation may cause damage or serious injury. Do not use this product for any purpose that is not explicitly specified in this manual. Do not exceed weight capacity. We cannot be liable for damage or injury caused by improper mounting, incorrect assembly or inappropriate use.

TIPOVER WARNING
SERIOUS OR FATAL CRUSHING INJURIES CAN OCCUR FROM TIPOVER.
TO HELP PREVENT TIPOVER:

• NEVER ALLOW CHILDREN TO CLIMB, STAND, HANG, OR PLAY ON ANY PART OF MONITOR OR STAND.
• USE TIPOVER RESTRAINT OR ANCHOR STAND TO WALL.

USE OF TIPOVER RESTRAINTS MAY ONLY REDUCE, BUT NOT ELIMINATE RISK OF TIP OVER. I

• SMALL PARTS- NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.

Supplied Parts List

INSTALLATION INSTRUCTIONS

• Step 1

  • Make sure that the supporting surface will safely support the combined load of the equipment and all attached hardware and components.
  • Tighten wood screws firmly but do not overtighten. Over tightening can damage the screws, greatly reducing their holding power
  • Make sure that mounting screws are anchored into the center of the studs. The use of an “edge to edge” stud finder is highly recommended.

• Step 2
  Option A : Wood Stud Mounting

  • Use a stud finder to locate the edges of  the studs. Using an edge-to-edge stud finder is highly recommended based ontheir edges and drew a vertical line down each stud’s center.

  • Place metal wall plate on the wall as a template. And mark the center of the two mounting holes. Make sure that the mounting holes are on the stud centerline.

  • Drill two 1/8″ (3mm) dia. Holes 1″ (25mm) deep. Secure it using two screws (part – ). Make sure that the wall plate is level as shown in the figure.
    Option B : Sold Brick and Concrete Wall Mounting

  • Use the metal wall plate as a template to mark two holes on the wall as shown in the figure.

  • Drill two 7/32″ (5.5mm) dia. Holes 1.2″ (30mm) deep. Insert a Concrete Anchor (Part- ) into each of these holes. Attach the wall plate to the wall using two screws (Part- ), make sure that the wall plate is level as shown in the figure.

• Step 3 Hand thread bolts into the threaded inserts on the back of your Speaker to determine which bolt to use. Attach Speaker to top bracket using Bolts B C D

• Step 4 Lastly, assemble the Speaker with the top bracket onto the bracket set and wall plate securely.

• Step 4
  Angle adjustments.

References

• TV mount, Monitor mount, Desk mount, TV Stand, Speaker mount,

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>